• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.565-570
• /
• 2001

Vehicle dynamics control (VDC) system requires more information on driving conditions compared with ABS and/or TCS. In order to develop the VDC system, tire slip angles, vehicle side-slip angle, and vehicle lateral velocity as well as road friction coefficient are needed. Since there are not any cheap and reliable sensors, recent researches on parameter estimation have given rise to a number of parameter estimation techniques. This paper presents new vehicle model to estimate vehicle's yaw rate. This model is improved from the conventional 2 degrees of freedom vehicle model, so-called bicycle model, taking nonlinear effects into account. These nonlinear effects are: (i) tyre nonlinearity; (ii) lateral load transfer during cornering; (iii) variable gear ratio with respect to vehicle velocity. Estimation results are validated with the experimental results.

• Journal of Power Electronics
• /
• 제10권6호
• /
• pp.724-732
• /
• 2010

This paper presents an effective rotor current controller for variable-speed stand-alone doubly fed induction generator (DFIG) systems feeding an unbalanced three-phase load. The proposed current controller is developed based on proportional plus two resonant regulators, which are tuned at the positive and negative slip frequencies and implemented in the rotor reference frame without decomposing the positive and negative sequence components of the measured rotor current. In addition, the behavior of the proposed controller is examined in terms of control performance and stability with respect to rotor speed variations, i.e., slip frequency variations. Simulations and experimental results are shown to validate the robustness and effectiveness of the proposed control method.

• International Journal of Aerospace System Engineering
• /
• 제7권2호
• /
• pp.1-5
• /
• 2020

When a rigid wedge is indented in to a semi-infinite block, the material is bulged up around the wedge that is generally called lip. The previous works in this filed considered the outer profile of the lip to be linear. But, present authors observed both experimentally and with the aid of finite element analysis that the profile of the lip is not always linear, and it depends on the angle of the wedge and friction parameters. So, in this work, attempts have been made to calculate hardness of indentation for different wedge angles and friction parameters. As hardness is intrinsic property of material, consideration of either linear or parabolic lip will not be affected much. A comparative study of hardness for linear and parabolic free surface profiles of the piled up material around the cone is analyzed in this work.

• Korean Journal of Geomatics
• /
• 제3권2호
• /
• pp.129-140
• /
• 2004

This paper addresses solutions th the challenges of carrier phase integer ambiguity resolution and cycle slip detection/identification, for maintaining high accuracy of an integrated GPS/Pseudolite/INS system. Such a hybrid positioning and navigation system is an augmentation of standard GPS/INS systems in localized areas. To achieve the goal of high accuracy, the carrier phase measurements with correctly estimated integer ambiguities must be utilized to update the system integration filter's states. The contribution presents an effective approach to increase the reliability and speed of integer ambiguity resolution through using pseudolite and INS measurements, with special emphasis on reducing the ambiguity search space. In addition, an algorithm which can effectively detect and correct the cycle slips is described as well. The algorithm utilizes additional position information provided by the INS, and applies a statistical technique known as th cumulative-sun (CUSUM) test that is very sensitive to abrupt changes of mean values. Results of simulation studies and field tests indicate that the algorithms are performed pretty well, so that the accuracy and performance of the integrated system can be maintained, even if cycle slips exist in the raw GPS measurements.

• Ocean Systems Engineering
• /
• 제1권4호
• /
• pp.263-283
• /
• 2011

The performance of a rig tie-down system on a TLP (Tension Leg Platform) is investigated for 10-year, 100-year, and 1000-year hurricane environments. The inertia loading on the derrick is obtained from the three-hour time histories of the platform motions and accelerations, and the dynamic wind forces as well as the time-dependent heel-induced gravitational forces are also applied. Then, the connection loads between the derrick and its substructure as well as the substructure and deck are obtained to assess the safety of the tie-down system. Both linear and nonlinear inertia loads on the derrick are included. The resultant external forces are subsequently used to calculate the loads on the tie-down clamps at every time step with the assumption of rigid derrick. The exact dynamic equations including nonlinear terms are used with all the linear and second-order wave forces considering that some dynamic contributions, such as rotational inertia, centripetal forces, and the nonlinear excitations, have not been accounted for in the conventional engineering practices. From the numerical simulations, it is seen that the contributions of the second-order sum-frequency (or springing) accelerations can be appreciable in certain hurricane conditions. Finally, the maximum reaction loads on the clamps are obtained and used to check the possibility of slip, shear, and tensile failure of the tie-down system for any given environment.

• 제어로봇시스템학회논문지
• /
• 제16권12호
• /
• pp.1212-1219
• /
• 2010

The most important thing in the container terminal is to handle the cargo effectively in the limited time. To achieve this object, many strategies have been introduced and applied to. If we consider the technical trends and environment of the automated container terminal, it is necessary that the systems for cargo handling are equipped with more intelligent control technologies. To cope with this tendency, from the middle of the 1990's, the automated RMGC (Rail-Mounted Gantry Crane) and RTGC (Rubber-Tired Gantry Crane) have been developed and widely used to handle containers in the yards. Recently, in these cranes, the many equipments like CCD cameras and sensors are mounted to cope with the automated terminal environment. If we want to obtain more efficient handling performance, the modelling, tracking control, anti-sway system design, skew motion suppressing and complicated motion control problems must be considered in the control system design and application process. Considering these problems, in this paper, the system modelling with the tire slip and a tracking control approach are proposed. Especially, we design the tracking control system based on the 2DOF servosystem design approach to cope with undesirable disturbance input. The experiment results show the desirable performance and usefulness of the designed control system.

• 전력전자학회논문지
• /
• 제10권3호
• /
• pp.233-240
• /
• 2005

본 논문은 현재까지 전적으로 수입에 의존하던 국내 교류 전동차용 추진제어장치(Converter/Inverter)를 대용량 IPM 스위칭 소자를 적용하여 개발된 시스템을 제안한다. 컨버터의 용량을 향상시키기 위해 2대의 PWM 컨버터를 병렬 운전하고 병렬 운전 시 각각의 컨버터 스위칭 각을 다르게 제어하여 고조파 함유를 줄였으며 DC-Link 단의 Beatless 제어를 수행하였다. VVVF 인버터 제어의 경우, 저속의 운전영역에서는 순시 토크 제어가 가능한 백터제어를 적용하고, 고속 운전 영역에서는 슬립 주파수제어를 적용하는 백터 제어와 스칼라 제어의 병용 제어기법을 제시하였다. 제시된 추진제어장치는 4대의 210kW 유도전동기를 이용하여 철도차량용 추진제어장치에 적용되는 관련 규격의 각종 시험을 통해 그 성능을 검증하였다.

• 전력전자학회논문지
• /
• 제12권3호
• /
• pp.248-257
• /
• 2007

본 논문은 사람의 근육에서 발생하는 근전위 신호를 사용하여 2 자유도를 갖는 전동의수를 구동하기 위한 제어시스템을 제안한다. 근전위 신호를 측정하기 위한 표면 근전위 센서는 근전위 신호의 출력 특성을 이용하여 근전위 센서의 입력부와 회로부를 설계한다. 제어시스템은 전동의수를 구동하기 위하여 두 개의 제어기와 전동의수의 파지력을 측정하기 위한 파지력 센서와 파지한 물체의 미끌림을 감지하기 위한 미끌림 센서로 구성되어 있다. 가상의 근전위 신호를 이용한 실험과 정상인의 실험을 통하여 제안된 제어시스템의 신뢰성을 검증하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1986년도 하계학술대회논문집
• /
• pp.20-23
• /
• 1986

• 한국전산구조공학회논문집
• /
• 제21권6호
• /
• pp.607-613
• /
• 2008

광섬유의 클래딩 부분을 별도의 고정구에 직접 부착하는 방식으로 고정하여, 변형발생 시 광케이블을 구성하는 재료들 사이에서 발생하는 미끄러짐(Slip)현상을 방지하고, 외력에 의해 발생하는 변형을 정확하게 측정이 가능하도록 함과 기존 광섬유격자센서가 자체적으로 압축변형의 측정이 곤란한 점을 개선하기 위해 미리 긴장(Pre-Strain)상태를 유지하기 위하여 두 개의 접점사이를 볼트와 너트로 조절하여 프리스트레인 가변이 가능하도록 하여 인장/압축변형 측정을 가능하게 한 광섬유격자센서 패키지를 사용하는 지하구조물 변위 모니터링시스템이 본 연구에 의해 개발되었다. 이러한 광섬유격자센서 패키지는 콘크리트 라이닝구조물에 콘크리트의 불균일성을 극복하고 대표성을 가지기 위해 1미터 게이지 길이를 갖도록 하여 모니터링시스템에 적용되었으며, 대구 지하철 지하구조물에 현재 운영 중인 이 시스템은 한국전력 공동구 설치공사가 진행되면서 구조물에 미치는 영향을 판단하기 위한 모니터링시스템으로 적용되었다.