• Journal of Electrical Engineering and Technology
• /
• v.11 no.3
• /
• pp.670-674
• /
• 2016

The control performance of hybrid PWM inverter using a phase current measurement is presented in this paper. The hybrid PWM technique consists of space vector pulse width modulation (SVPWM) and six-step voltage control operation. The SVPWM is performed to reduce the harmonic components in the low speed region, and the six-step modulation is applied to increase the maximum speed of the IPMSM in the high speed region. Therefore, it is possible to obtain a great performance in both the low speed range and high speed range. However, the six-step modulation cannot be completely implemented, since the inverter that includes the lag-shunt sensing method has an immeasurable current region. In this paper, a quasi-six-step modulation using a modified voltage vector is proposed. The validity and usefulness of the proposed PWM technique is verified by MATLAB/Simulink and experimental results.

• 한국연소학회:학술대회논문집
• /
• 2012.04a
• /
• pp.195-196
• /
• 2012

This paper describes combustion tuning methodology of double-swirl gas turbine combustor using six sigma tools. This methodology is consist of five steps-Define, Identify, Design, Optimize and Verify (DIDOV). First, the NOx reduction target was defined in the step design; second, the current status of the plant was diagnosed in the step of identify; third, the vital few control parameters to achieve the defined target were determined by analyzing the correlation between the control parameters and NOx emissions in the step of design; fourth, the optimum condition was derived from one of the six sigma tools in the step of optimize; finally, the optimum condition was verified by applying the condition to the gas turbine combustor in the step of verify. As a result of the suggested method, averaged NOx emissions were reduced by more than 70% and the standard deviation was improved by more than 60%. Thus, this methodology can be attributed to the efficient reduction of NOx emission with saving combustion tuning time.

• Journal of Power Electronics
• /
• v.11 no.4
• /
• pp.449-455
• /
• 2011

Electric drive vehicles (EDV) have received much attention recently because of their environmental and energy benefits. In an EDV, the motor drive system directly influences the performance of the propulsion system. However, the available DC voltage is limited, which limits the maximum speed of the motors. At high speeds, the inverter voltage increases if the square wave (SW) voltage (six-step operation) is used. Although conventional direct torque control (DTC) has several advantages, it cannot work in the six-step mode required in high-speed applications. In this paper, a single-mode seamless DTC for AC motors is proposed. In this scheme, the trajectory of the reference flux changes continuously between circular and hexagonal paths. Therefore, the armature voltage changes smoothly from a high-frequency switching pattern to a square wave pattern without torque discontinuity. In addition, because multi-mode controllers are not used, implementation is more straightforward. Simulation results show the voltage pattern changes smoothly when the motor speed changes, and consequently, torque control without torque discontinuity is possible in the field weakening area even with a six-step voltage pattern.

• The Journal of Korea Robotics Society
• /
• v.2 no.1
• /
• pp.55-63
• /
• 2007

Mobile robots traveling on rough terrain need several algorithms to overcome obstacles. In this paper, we propose the step-type obstacle traversal algorithm to adapt the mobile robot with six arms and wheels to travel on rough terrain. Obstacle traversal is composed of two different stages: planning and control. In planning stage, the required joint torque of each arm as well as the interference between the wheels and the arms are analyzed to guarantee traversing obstacles. Control stage includes such steps as checking distance to obstacle, determining the height and length of obstacle, performing arm motion according to sensed torque data, and evaluating safety at every instance. The proposed algorithm is designed and implemented for CALEB 1 six legged robot developed in the laboratory and verified by simulation and experiment in outdoor environment.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.49-52
• /
• 1987

In this work, the characteristics of a six step inverter fed brushless DC motor are analyzed and the control of amplitude of inverter input voltage and phase shift of a six step inverter is discussed. The effects of the motor performance, efficiency and power factor, are studied.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.72-81
• /
• 2018

In this study, the sinusoidal-wave driving method, six-step driving method, and twelve-step driving method, which can be used in an inverter for permanent-magnet synchronous motors, were simulated, and the results were compared to review their operating performance. These driving methods were classified according to the electrical conduction angle and phase current of the motor. Conventionally, only the transition control technique between the sinusoidal-wave driving method and six-step driving method was studied for the efficiency of the inverter. In this paper, however, comparative analysis was focused on a variety of transition control applications to use the advantages of each driving method. For this purpose, computer simulations for these driving methods were carried out to obtain the motor torque, speed control characteristics, and THD of the motor phase currents. As a result, the sinusoidal-wave driving method showed the best performance in all respects. The six-step driving method has better speed control characteristics than the twelve-step driving method, and the twelve-step driving method has a lower THD of the motor phase currents than the six-step driving method.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.175-176
• /
• 2007

본 논문은 매입형 영구자석 동기 전동기의 준 식스스텝 운전(Quasi six-step operation)을 위한 약자속 제어에 대한 새로운 방법을 제안한다. 제안된 방법은 전향 경로(feedforward path)와 궤환 경로(feedback path)로 구성되고 전향 경로는 1차원 참조표로 구성되며 궤환 경로는 전류제어기 출력과 과변조에 의해 제한된 전압의 차이를 이용한다. 제안된 방법을 통해 약자속 제어와 안티 와인드업(anti-windup) 제어가 동시에 이루어질 수 있다. 또한 제한된 직류단 전압 조건에서 식스 스텝(six-step) 운전에서 낼 수 있는 전동기의 최대 토크에 가까이 출력 토크를 발생시키면서 전류 제어를 계속할 수 있는 준 식스 스텝 운전이 가능하다. 제안된 방법의 유효성을 컴퓨터 시뮬레이션과 실험의 결과를 통해 입증하였다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.1
• /
• pp.101-110
• /
• 2002

A method to control the inverter output voltage lineally in over modulation mode of the third harmonics injected PWM inverter is proposed. The third harmonics injected PWM has a extended linear region compared with the sine PWM. But it still has a maximum voltage about 90% compared with the six step inverter. Therefore, to control the output voltage linearly in over modulation mode, analyzing the relationship between the modulation index and the peak of the fundamental component of the modified reference voltage, we can settle the problem in over modulation mode without iteration. Then we can increase the maximum fundamental component of the third harmonics injected PWM inverter comparative to six-step inverter continuously in over modulation mode. The simulation results of the inverter-induction motor system shows the validity of this method and experimental results prove it.

• International Journal of Automotive Technology
• /
• v.6 no.6
• /
• pp.625-633
• /
• 2005

Vehicle drift was reduced using statistical six sigma tools. The study was performed through four steps: M (measure), A (analyze), I (improve), and C (control). Step M measured the main factors which were derived from a fishbone diagram. The measurement system capabilities were analyzed and improved before measurement. Step A analyzed critical problems by examining the process capability and control chart derived from the measured values. Step I analyzed the influence of the main factors on vehicle drift using DOE (design of experiment) to derive the CTQ (critical to quality). The tire conicity and toe angle difference proved to be CTQ. This information enabled the manufacturing process related with the CTQ to be improved. The respective toe angle tolerance for the adjustment process was obtained using the Monte Carlo simulation. Step C verified and controlled the improved results through hypothesis testing and Monte Carlo simulation.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.3
• /
• pp.158-164
• /
• 2000

In recent year, desire and request fer micro automation are growing rapidly covering the whole range of the industry. This has been caused mainly by request of more accurate manufacturing process due to a higher density of integrated circuits in semiconductor industry. This paper presents a six d.o.f fine motion stage using magnetic levitation technique, which is one of actuating techniques that have the potential for achieving such a micro motion. There is no limit in motion resolution theoretically that the magnetically levitated part over a fixed stator can realize. In addition, it Is possible to manipulate the position and the force of the moving part at the same time. Then, the magnetic levitation technique is chosen into the actuating method. However, we discuss issues of design, kinematics, dynamics, and control of the proposed system. And a few experimental results fur step input are given.