• Journal of Advanced Marine Engineering and Technology
• /
• 제31권8호
• /
• pp.975-982
• /
• 2007

The single-phase switched reluctance motor(SRM) drive requires DC source which is generally supplied through a rectifier connected with a commercial source. The rectifier is consist of a diode full bridge and a filter circuit. Usually the filter circuit uses capacitor with large value capacitance to reduce ripple component of DC power. Although the peak torque ripple of SRM is small, the short charge and discharge current of the filter capacitor draws the low power factor and system efficiency. A modified single phase SRM drive system is presented in this paper, which includes drive circuit realizing reduction of torque ripple and improvement of power factor. In the proposed drive circuit, one switching part and diode which can separate the output of AC/DC rectifier from the filter capacitor is added. Also, a upper switch of drive circuit is exchanged a diode in order to reduce power switching device. Therefore the number of power switch device is not changed, two diodes are only added in the SRM drive. To verify the proposed system, some simulation and experimental results are presented.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.123-125
• /
• 2001

Salient pole rotor type single phase SRM(switched reluctance motor) uses the magnetic fluxes of radial and axial direction at the same time. Therefore the output power per unit volumn is very high and shaft length can be shorter than any other types of SRM with same output. Also, It can be manufactured with low cost thanks to simple structure and driving circuit. We already designed and manufactured prototype using the dynamic output equation of general rotating machine but the effect by salient pole structure was not considered. The most optimal design parameters for salient pole rotor type single phase SRM will be selected by comparing and analyzing the results from 3D FEM analysis, experimental values of the torque versus speed characteristics. and the nux linkage of prototype. Results for the former 3D FEM analysis and torque vs. speed characteristics were already obtained. Finally, we will measure the nux linkage of salient pole rotor type single phase SRM.

• 산업기술연구
• /
• 제25권A호
• /
• pp.157-162
• /
• 2005

In this study, the fabrication of PZT films was performed from a multilayer structure comprising $TiO_2$, $ZrO_2$ and PbO thin films prepared by rapid themal chemical vapor deposition(RTMOCVD). $TiO_2$, $ZrO_2$ and PbO are the component layers of oxide multilayer system for a single phase PZT thin film. The composition control of PZT thin film was done by the thickness control of individual component layer. The composition ratio of Pb:Ti:Zr with thickness were 1:0.94:0.55. Occurrence of a single-phase of PZT was initiated at around $550^{\circ}C$ and almost completed at $750^{\circ}C$ under the fixed time of 1hr. As the concentration of Pb increased, the roughness and crystallization in the film increased. From the as result of using XPS and TEM, the single phase formation through annealing is evident. The electrical properites of the prepared PZT thin film(Zr/Ti=40/60, 300 nm) on a Pt-coated substrate were as follow: dielectric constant ${\varepsilon}_r=475$, coercive field Ec=320 kV/cm, and remanant polarization $P_r=11{\mu}C/cm^2$ at an applied voltage of 18 V.

• Journal of Electrical Engineering and Technology
• /
• 제13권5호
• /
• pp.1978-1985
• /
• 2018

In this paper, a novel single-phase hybrid switched reluctance motor (HSRM) is proposed for hammer breaker application. The hammer breaker requires only unidirectional rotation and high-speed operation. To satisfy the requirements and eliminate torque dead-zone, the rotor of the proposed 4/4 poles SRM is designed with wider pole arc and non-uniform air-gap. This motor has a simple structure and produces low torque ripple. Permanent magnets (PMs) are mounted on the inner stator at a certain position which enables it to park the rotor for self-start and create positive cogging torque in the torque dead-zone. Compared with conventional single-phase switched reluctance motor, HSRM has an increased torque density and relatively low torque ripple. To verify effectiveness, finite element method (FEM) is employed to analyze the performance of the proposed structure. Then, the proposed motor is compared with the existing motor drive system for the same application. The proposed HSRM is easy to manufacture along with competitive performance.

• 조명전기설비학회논문지
• /
• 제29권8호
• /
• pp.90-97
• /
• 2015

This paper discusses to the capability improvement of the 1/4 HP compressor. And, for efficiency improvement of the single phase induction motor, this paper has proposed a casting method to improving the fill factor of the rotor of the single phase induction motor. First, by using FEM, it was analyzed the magnetic flux distribution and the fill factor to the SPIM rotor by the conventional method and the proposed method. And, based on the FEM analysis results, SPIMs are manufactured by the each casting process. Through experiments using dynamometer, they were compared and measured to their efficiencies. In addition, through experiments using Calorimeter, we have analyzed the refrigerating capacity of the compressor of which they were applied. Based on the results of the previous two experiments, they are to verify the validity of the proposed method.

• 한국산학기술학회논문지
• /
• 제11권7호
• /
• pp.2570-2578
• /
• 2010

본 논문에서는 임계전류도통모드로 동작하는 디지털제어 단상 역률개선(PFC; power-factor correction) 컨버터를 제안한다. 제안한 컨버터는 PFC를 위하여 DC-DC 부스트 컨버터 구조를 이용하며 인덕터전류를 임계도통모드로 동작시킨다. 또한 제안한 컨버터는 마이컴을 이용하여 디지털적으로 제어되기 때문에 제어회로는 간단해지고 컨버터는 더욱 효과적으로 동작한다. 본 논문에서는 먼저 제안한 컨버터의 동작원리를 설명하고 회로를 해석한다. 그리고 본 논문은 제안한 컨버터의 구현방법을 소프트웨어와 회로설계 부분으로 구분하여 구체적인 설계예와 함께 설명한다. 또한 설계된 회로파라미터에 의한 프로토타입 컨버터의 실험결과로 제안한 컨버터가 단상 PFC 컨버터로써 좋은 동작 특성을 가지고 있음을 보인다.

• 전력전자학회논문지
• /
• 제12권4호
• /
• pp.346-353
• /
• 2007

본 논문은 단상풀브릿지 구조를 갖는 계통연계형 전압형 PWM 인버터를 위한 필터설계를 목적으로 한다. 단상풀브릿지 전압형 PWM 인버터의 교류출력단 전압과 계통전압의 관계를 분석하여 필터인덕터에 순시적으로 인가되는 전압의 특징적인 관계를 정성적 및 정량적으로 파악하였다. 교류출력단 전압의 분석을 기초로 하여 필터인덕터에 흐르는 스위칭리플전류의 크기를 정량적으로 구하였다. 이러한 분석을 기초로 하여 계통주입전류의 기본파성분에 대한 리플전류의 비율을 평가함수로 하는 필터인덕터의 설계법을 제시하였다. 제안된 설계방법을 시뮬레이션 및 실험을 통하여 검증하였다.

• 전력전자학회논문지
• /
• 제17권5호
• /
• pp.409-415
• /
• 2012

This paper presents a new software-based on-line dead-time compensation technique for a single-phase grid-connected photovoltaic (PV) inverter system. To prevent a short circuit in the inverter arms, a switching delay time must be inserted in the pulse width modulation (PWM) signals. This causes the dead-time effect, which degrades the system performance around zero-crossing point of the output current. To reduce the dead-time effect around the zero-crossing point of grid current, a harmonic mitigation of grid current is used as an additional part of the synchronous frame current control scheme. This additional task mitigates the harmonic components caused by the dead-time from the grid current. Simulation and experimental results are shown to verify the effectiveness of the proposed dead-time compensation method in the single-phase grid-connected inverter system.

• 전력전자학회논문지
• /
• 제17권5호
• /
• pp.377-387
• /
• 2012

A single-phase grid-connected PV system is known as suitable for housing of less than 3 kW. The DC link voltage in a single-phase PV system has necessarily twice component of fundamental wave. It makes high THD in the grid current. According to the problem, power quality is lower. Many engineers have studied about this problem. The most simple method is to use low pass filter on DC link voltage control. However it is affected by DC link voltage control bandwidth. If cutoff frequency is reduced to increase the performance of low pass filter, it also lowers DC link voltage control bandwidth. Second method is using band stop filter, it works good on steady state but not good on transient state. This paper proposes the new method for removing ripple voltage to get an exact current reference. It improves the responses on steady state and transient state. The performance was verified through computer simulation using MATLAB and actual experiments.

• 전력전자학회논문지
• /
• 제26권3호
• /
• pp.176-182
• /
• 2021

This research proposes a high-frequency circuit that can accurately predict the differential mode noise of single-phase inverters at the circuit design stage. Proposed single-phase inverter high frequency circuit in the work is a form in which harmonic impedance components are added to the basic single-phase inverter circuit configuration. For accurate noise prediction, parasitic components present in each part of the differential noise path were extracted. Impedance was extracted using a network analyzer and Q3D in the measurement range of 150 kHz to 30 MHz. A high-frequency circuit model was completed by applying the measured values. Simulations and experiments were conducted to confirm the validity of the high-frequency circuit. As a result, we were able to predict the resonance point of the differential mode voltage extracted as an experimental value with a high-frequency circuit model within an approximately 10% error. Through this outcome, we could verify that differential mode noise can be accurately predicted using the proposed model of the high-frequency circuit without a separate test bench for noise measurement.