• 전기전자학회논문지
• /
• 제16권2호
• /
• pp.127-130
• /
• 2012

In this paper, we reported on a single balanced monolithic diode mixer using Marchand balun for millimeter-wave applications. The single balanced monolithic mixer was fabricated using drain-source-connected pseudomorphic high electron mobility transistor (PHEMT) diodes considering the PHEMT MMIC full process. The average conversion loss is 16 dB in the RF frequency range of 81~86 GHz at LO frequency of 75 GHz with LO power of 10 dBm. The RF-to-LO isolation characteristics are greater than -30 dB and the total chip size is $1.0mm{\times}1.35mm$.

• Journal of Power Electronics
• /
• 제10권4호
• /
• pp.365-373
• /
• 2010

This paper proposes a hybrid single carrier sinusoidal modulation suitable for multiphase multilevel inverters. Multiphase multilevel inverters are controlled by hybrid modulation to provide multiphase variable voltage and a variable frequency supply. The proposed modulation combines the benefits of fundamental frequency modulation and single carrier sinusoidal modulation (SC-SPWM) strategies. The main characteristics of hybrid modulation are a reduction in switching losses and improved harmonic performance. The proposed algorithm can be applied to cascaded multilevel inverter topologies. It has low computational complexity and it is suitable for hardware implementations. SC-SPWM and its base modulation design are implemented on a TMS320F2407 digital signal processor (DSP). A Complex Programmable Logic Device realizes the hybrid PWM algorithm and it is integrated with a DSP processor for hybrid SC-SPWM generation. The feasibility of this hybrid modulation is verified by spectral analysis, power loss analysis, simulation and experimental results.

• Composites Research
• /
• 제32권1호
• /
• pp.78-84
• /
• 2019

본 연구에서는 동적기계분석장치(dynamic mechanical analysis, DMA)와 시간-온도 중첩법(time-temperature superposition, TTS)을 이용하여 탄소섬유/에폭시 복합재의 장기 성능을 예측하고자 하였다. 이를 위해 단일 진동수 시험, 다중 진동수 시험, 크리프 TTS 시험을 수행하였다. 단일 진동수(single-frequency) 시험과 다중 진동수(multi-frequency) 시험에서는 $-30^{\circ}C$에서 $240^{\circ}C$까지 $2^{\circ}C/min$로 온도를 상승시키면서 $20{\mu}m$ 진폭의 사인(sine) 파형의 하중을 가하였으며 다중 진동수 시험에 적용된 진동수는 0.316, 1, 3.16, 10, 31.6 Hz이다. 크리프 TTS 시험에서는 $-30^{\circ}C$에서 $230^{\circ}C$까지 $10^{\circ}C$마다 15 MPa의 응력을 10분 동안 가하였다. 단일 진동수 시험을 통해 유리전이온도를 구하였으며 다중 진동수 시험을 통해 진동수 별 유리전이온도에서 활성화 에너지와 온도 별 저장탄성계수 선도를 구하였다. 또한 아레니우스 식(Arrhenius equation)을 통해 얻은 이동 인자를 적용하여 기준 온도에 대한 마스터 선도를 얻었다. 또한 크리프 TTS 시험을 통해서는 크리프 컴플라이언스 선도를 구하고 직접 이동 기법을 이용하여 구한 이동 인자를 적용하여 기준 온도에 대한 마스터 선도도 얻었다. 이와 같은 과정을 통해 얻은 마스터 선도를 이용하면 주어진 환경 조건에 대한 탄소섬유강화 복합재의 장기 성능을 예측할 수 있다.

• 대한전자공학회논문지SD
• /
• 제42권5호
• /
• pp.9-14
• /
• 2005

본 논문은 순수한 고주파 (radio-frequency: rf) 모드의 반사형과 투과형 고주파 단일전자 트랜지스터 (RF-SET) 동작의 새로운 시뮬레이션 기법을 소개한다. 이 기법은 RF-SET 회로를 주파수 영역에서 self-consistent 방법으로 키리히호프 법칙에 기반한 미분 방정식의 해를 구한다. 또한, 이 기법은 정상상태와 시변 단일전자 트랜지스터 전류 모델들 두 가지를 포함한다. 순수한 rf 모드 반사형 RF-SET의 반사파와 순수한 rf 모드 투과형 RF-SET의 투과파를 계산한다. 정상상태 단일전자 트랜지스터 전류 모델을 포함한 RF-SET 계산의 정확성은 [참고문헌 2]에서 소개된 방법으로 확인한다. GHz 이상의 고주파에서 시변 단일전자 트랜지스터 전류 모델을 포함한 RF-SET 계산 결과는 정상상태 단일전자 트랜지스터 전류 모델을 포함해서 RF-SET를 계산한 결과들과 상당한 차이가 있음을 확인했다. GHz 이상 고주파에서 RF-SET 동작 분석은 정확한 시변 단일전자 트랜지스터의 전류 모델이 요구된다.

• 한국환경과학회지
• /
• 제31권4호
• /
• pp.369-372
• /
• 2022

This study was conducted to determine the injury type and frequency of bearded dragons during single and group breeding according to stocking density, for 16 weeks. A total of 14 bearded dragons compromising three groups were selected for this study. Six and four bearded dragons bred in a cage of 45 cm × 45 cm × 45 cm were designed as group A and B, respectively. Group C was made of four partitions (20 cm × 20 cm × 20 cm) of equal size in the kennel, and the dragons, four in number, were reared alone. Injury type criteria were given 1 score each in 6 stages. Most of the injury types in group A were primary tail cutting, which was 1 point, depending on the score, except for 4 scores. The injury type of group A varied, that is 1, 2, 3, and 5 scores, and the pattern lasted for 2 to 9 weeks. After 10 weeks, the dragons showed no response to injury type, except 4 scores at 11 weeks and 2 scores at 14 weeks with a frequency of one, respectively. The representative injury types of the group B were primary tail cutting, which was 1 point, and the scores of the injury type from 2 to 11 weeks were the highest; the frequency of occurrence at 1 and 2 scores was 5 times and 3 times, respectively, and the frequency of occurrence at 3 scores was twice. In addition, 5 scores were found to have the lowest frequency of occurrence. Solitary breeding showed no response to the type of injury for 16 weeks. Consequently, single breeding with an appropriate stocking density did not affect stress, and it could be expected a positive aspect for pet welfare.

• 한국항행학회논문지
• /
• 제2권1호
• /
• pp.22-33
• /
• 1998

마그네트론을 이용하는 레이다에서 송신 주파수의 변화를 감지하여 안정된 중간주파수를 발생하기 위해서는 STALO(Stable Local Oscillator)로서 AFC(Automatic Frequency Control)에 의해 출력주파수를 조정할 수 있는 주파수 합성기(Frequency Synthesizer)가 이용된다. 본 논문에서는 8.4GHz~9.7GHz의 X-밴드 주파수 합성기를 단일 루우프 구조의 간접 주파수 합성방식으로 설계하고 제작하였다. 고속 디지털 PLL 칩에 의하여 위상비교를 하고, 저 위상잡음을 구현하기 위한 여파기를 설계하였다. 기준신호와 VCO, 주파수 분주기, 여파기 등의 특성에 따른 단일 루우프 주파수 합성기의 위상잡음 성능을 해석하고, 위상잡음이 최소가 되도록 설계하여 측정치와 비교하였다.

• 수산해양기술연구
• /
• 제41권3호
• /
• pp.207-212
• /
• 2005

Dual frequency acoustic pinger(AP) was manufactured to reduce study effect by long-term use of developed single frequency AP to prevent cetacean bycatch. Directivity characteristic of transducer was the omnidirectional pattern which showed less than ${\pm}3dB$ the change range of sensitivity on the beam pattern of right and left. Source power level(SPL) was 1384311pa with epoxy window before casing however after casing 1170B11Pa at sea. Dual frequency Af was tested to identify the avoidance behavior of bottlenose dolphin by its working. However the efficiency of dual frequency AP about the study effect was verified experiment repeatedly using single and dual frequency AP.

• International Journal of Fluid Machinery and Systems
• /
• 제9권1호
• /
• pp.1-16
• /
• 2016

Behaviors of surges appearing near the stall stagnation boundaries in various fashions in systems of a single-stage compressor and flow-path systems were studied analytically and were tried to put to order. Deep surges, which enclose the stall point in the pressure-mass flow plane, tend to have either near-resonant surge frequencies or subharmonic ones. The subharmonic surge is a multiple-loop one containing, for example, in a (1/2) subharmonic one, a deep surge loop and a mild surge loop, the latter of which does not enclose the stall point, staying only within the stalled zone. Both loops have nearly equal time periods, respectively, resulting in a (1/2) subharmonic surge frequency as a whole. The subharmonic surges are found to appear in a narrow zone neighboring the stall stagnation boundary. In other words, they tend to appear in the final stage of the stall stagnation process. It should be emphasized further that the stall stagnation initiates fundamentally at the situation where a volume-modified reduced resonant-surge frequency becomes coincident with that for the stagnation boundary conditions, where the reduced frequency is defined by the acoustical resonance frequency in the flow-path system, the delivery flow-path length and the compressor tip speed, modified by the sectional area ratio and the effect of the stalling pressure ratio. The real surge frequency turns from the resonant frequency to either near-resonant one or subharmonic one, and finally to stagnation condition, for the large-amplitude conditions, caused by the non-linear self-excitation mechanism of the surge.

• Smart Structures and Systems
• /
• 제6권5_6호
• /
• pp.661-673
• /
• 2010

This paper presents recent developments in an extremely compact, wireless impedance sensor node (the WID3, $\underline{W}$ireless $\underline{I}$mpedance $\underline{D}$evice) for use in high-frequency impedance-based structural health monitoring (SHM), sensor diagnostics and validation, and low-frequency (< ~1 kHz) vibration data acquisition. The WID3 is equipped with an impedance chip that can resolve measurements up to 100 kHz, a frequency range ideal for many SHM applications. An integrated set of multiplexers allows the end user to monitor seven piezoelectric sensors from a single sensor node. The WID3 combines on-board processing using a microcontroller, data storage using flash memory, wireless communications capabilities, and a series of internal and external triggering options into a single package to realize a truly comprehensive, self-contained wireless active-sensor node for SHM applications. Furthermore, we recently extended the capability of this device by implementing low-frequency analog-to-digital and digital-to-analog converters so that the same device can measure structural vibration data. The compact sensor node collects relatively low-frequency acceleration measurements to estimate natural frequencies and operational deflection shapes, as well as relatively high-frequency impedance measurements to detect structural damage. Experimental results with application to SHM, sensor diagnostics and low-frequency vibration data acquisition are presented.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.430-432
• /
• 2005

This paper presents a novel, single stage, isolated, three-phase switching rectifier capable of switching at high frequency. The circuit topology Provides zero-voltage switching for all switches, output voltage regulation, unity input power factor, all in a single power conversion stage. Operating principle and experimental results in the 48V/100A DC power supply of three-phase single stage method are presented.