• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제50권5호
• /
• pp.238-245
• /
• 2001

During an AC motor's start-up accelerating period, a large amount of current is required to reach to the rating speed. This is called in-rush current. This peak in-rush current can be more than about several times the operating or steady-state current in the full load rating of the motor. In-rush current is present in both and electronic ballasts. The main area of concern is the tripping of circuit breaker and fuses which can affect electrical system components From this, we can see that the electrical power controllers will be rather concerned, since they have to supply the actual current necessary to start the motor. This paper presents a new method to reducing in-rush current and energy saving of the single-phase induction motor used in air-conditioner. It can be obtained that proposed system is low cost and small size as compared with other controller. Experiments are focused on a capacitor starting single-phase induction motor. The optimal power saving and in-rush current limiting by phase angle control are verified by experimental results. Also, auxiliary winding was controlled by electronic starting switch.

• 전기학회논문지P
• /
• 제60권4호
• /
• pp.220-226
• /
• 2011

This paper proposes a straightforward method of analyzing the operation characteristics for the capacitor run single-phase induction motor from the traditional equivalent circuit based on the revolving field theory. The proposed method consists of five procedures as follows: mechanical loss segregation, iron loss segregation and calculation of the equivalent circuit parameters, recalculation of parameters of the main winding side, calculation of the auxiliary winding magnetizing reactance and effective turn ratio, and analyzing the operation characteristics for this motor. When the characteristics are analyzed, the segregated mechanical and iron losses are considered as a loss resistance across input terminals of the equivalent circuit for the analysis. The validity of the proposed method is verified from the comparison between the computed results and the experimental ones for the operation characteristics.

• 조명전기설비학회논문지
• /
• 제18권4호
• /
• pp.97-103
• /
• 2004

단상 유도전동기의 기동전류는 정격전류의 3-6배로 전등의 명멸, TV 화면의 산란, 전동기의 절연 열화, 옥내배선의 순간적인 열화 등을 발생시켜 전력손실, 가전제품의 효율저하 및 수명을 단축시키고 있다. 이러한 문제점을 개선하기 위해 본 논문에서는 트라이액과 교류변류기를 사용하여 기동전류를 3.7(%) 감소시키는 방법을 제안하였으며, 또한 반도체 소자를 사용함으로써 수명은 반영구적임을 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.912-915
• /
• 1993

In this paper, the speed of single phase induction motor driven by full bridge inverter is controlled by a PID controller under condition of disturbance load and setpoint changes, and the current characteristics of the system is investigated to look for the good properties of A.C. motor torque through the results of experiment. From the experimental result, it is confirmed that the speed of single phase induction motor driven by full bridge series inverter can be smoothly controlled by an analog PID controller.

• 전기학회논문지P
• /
• 제53권2호
• /
• pp.58-64
• /
• 2004

Most of the loads in industrial power distribution systems are balanced and connected to three power systems. However, in the user power distribution systems, most of the loads are single & three phase and unbalanced, generating voltage unbalance. Voltage unbalance is a condition in a polyphase system in which the rms values of the line-to-line voltages or the phase angles between consecutive line-to-line voltages, are not all equal. Slight voltage unbalance generates a disproportionately high current unbalance at the motor stator winding. This paper presents a scheme on operation states of a three-phase induction motor under unbalanced voltages. The three-phase voltages applied to the stator winding of the studied induction motor are controlled by respectively adjusting the magnitude and phase angle of each phase. The voltage unbalanced factor(VUF) of the three-phase source voltages can then be varied to examine the different values of VUF on machine's operation characteristics.

• 전기학회논문지
• /
• 제56권4호
• /
• pp.693-698
• /
• 2007

In general the distributed winding method is applied for induction motor in order to have the sinusoidal flux distribution. Recently the concentrated winding method is the interested technique so as to lower the material cost portion of copper coil. In the concentrated winding induction motor the harmonic flux and the torque deterioration by it would be occurred. To restrain ill effect of harmonic flux distribution by concentrated winding, the skew of rotor conduction bar is very important design variable. This study is focused on the optimal design of rotor bar's skew and winding turns for concentrated winding induction motor. In this study, the control method of harmonic parasitic torque in concentrated winding induction motor is proposed and validated its practicality through the experiment. As a result of this study, large skew angle which was not conventional in distributed winding was favorable in the concentrated winding induction motor. The concentrated winding induction motor which is designed per the proposed method of this study can be manufactured more cost effectively than conventional distributed winding.

• 조명전기설비학회논문지
• /
• 제21권1호
• /
• pp.125-130
• /
• 2007

단상유도전동기는 상용화된 전원을 변환장치 없이 직접 사용할 수 있어 가전제품의 전 분야의 동력원으로 사용되고 있다. 이와 같은 단상유도전동기를 해석하고 효율적으로 운용하기 위해서는 내부 등가회로 정수의 정확한 산출이 요구된다. 순단상유도전동기의 해석에는 교차자계설에 의한 방법과 회전자계설에 의한 방법이 있다는 것은 주지의 사실이지만 기존의 이론이나 방법에서 전동기 내부 정수를 산정하기 위한 방법은 다소 복잡하다. 최근 컴퓨터나 마이크로 프로세서의 발전에 따라 수치적 해석법과 등가회로법을 결합한 회로정수의 산정법이 제안되고 그 계산 처리 속도 또한 빠르며 정확해 지고 있다. 이에 정수 측정 전용 프로그램을 구현하여 단상유도전동기의 실험 결과를 산출하여 실시험을 이용하여 구하는 방법을 제시하고자 한다. 본 논문에서는 단상유도전동기에서 개별적으로 측정이 불가능한 1차 및 2차 누설리액턴스를 무부하시험, 구속시험, 그리고 고정자 권선의 저항 측정시험을 디지털 계측기를 이용하여 정확히 측정하고 측정한 디지털 계측값을 구현된 회로정수 계산프로그램으로 계산후 산출하는 방법을 제시하고 시행하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.284-286
• /
• 1995

The most common for starting a single phase induction motor is to install a starting condenser and a centrifugal switch in series with the auxiliary winding. Though this method is simple, life of single phase induction motor is short because of malfunction of a starting condenser and a centrifugal switch and efficiency improvement has limitation. In this paper, the starting characteristics of SPIM is improved by voltage and phase control strategy of auxiliary winding in removing a starting condenser and a centrifugal switch. Finally, the excellent starting performance of SPIM is shown through simulation and experimental results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.19-21
• /
• 2008

The purpose of this paper is the optimal design of a single-phase LSPM(Line-Start Permanent Magnet Motor). A single-phase LSPM has a permanent magnet in the rotor that is same as induction motor. For that reason, magnet is operated by breaking torque in starting region and alignment torque in driving region. Therefore, we need the design process considering the trade-off relationship. In this paper, we propose the design process of a single-phase LSPM for a high starting torque and efficiency with equivalent circuit and FEM. And we use Taguchi Method for considering tolerance in manufacture. Finally, we compared the LSPM that is designed in this paper and conventional induction motor.

• Journal of Electrical Engineering and Technology
• /
• 제9권3호
• /
• pp.899-907
• /
• 2014

This paper deals with fault-tolerant control of five-phase induction motor (IM) drives under single-phase open. By exploiting a decoupled model for five-phase IM under fault, the indirect field-oriented control ensures that electromagnetic torque oscillations are reduced by particular magnitude ratio currents. The control techniques are developed by the third harmonic current injection, in order to improve electromagnetic torque density. Furthermore, Proportional Resonant (PR) regulator is adopted to realize excellent current tracking performance in the phase frame, compared with Proportional Integral (PI) and hysteresis regulators. The analysis and experimental results confirm the validity of fault-tolerant control under single-phase open.