• 한국세라믹학회지
• /
• 제49권6호
• /
• pp.620-624
• /
• 2012

The role of moisture remaining inside the deposition chamber during the formation of the cubic boron nitride (c-BN) phase in BN film was investigated. BN films were deposited by an unbalanced magnetron sputtering (UBM) method. Single-crystal (001) Si wafers were used as substrates. A hexagonal boron nitride (h-BN) target was used as a sputter target which was connected to a 13.56 MHz radiofrequency electric power source at 400 W. The substrate was biased at -60 V using a 200 kHz high-frequency power supply. The deposition pressure was 0.27 Pa with a flow of Ar 18 sccm - $N_2$ 2 sccm mixed gas. The inside of the deposition chamber was maintained at a moisture level of 65% during the initial stage. The effects of the evacuation time, duration time of heating the substrate holder at $250^{\circ}C$ as well as the plasma treatment on the inside chamber wall on the formation of c-BN were studied. The effects of heating as well as the plasma treatment very effectively eliminated the moisture adsorbed on the chamber wall. A pre-deposition condition for the stable and repeatable deposition of c-BN is suggested.

• 한국안전학회지
• /
• 제34권1호
• /
• pp.40-44
• /
• 2019

Experimental studies have been carried out to investigate characteristics of gas explosion using a multi layered water gel barrier in a vented explosion chamber. The chamber is consisted of 1600 mm in length, with a square cross-section of $100{\times}100mm^2$. The gel concentration of inner layer of MLWGB ranged from 10% to 90% with intervals of 10% by weight of gel. Displacement of the MLWGB was photographed with a measured using a high-speed video camera, and pressure development was measured using a data acquisition system. It was found that MLWGBs with 10 ~ 20% inner layer concentrations were ruptured during the explosions. As the concentrations of inner layer increased from 30% to 90%, the barriers were not ruptured. As the gel concentrations of the inner layer increased, the displacement increased toward the chamber exit and the pressure decreased for the ruptured barriers. It was found that the pressure attenuation obtained from the MLWGB was higher than that of the single water gel barrier. For the cases of non-ruptured barriers, the pressure inside the chamber less increased with increasing gel concentrations of the inner layer. It was also found that the displacement moved back into the chamber for non-ruptured MLWGBs, and it was sensitive to the gel concentrations.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1354-1359
• /
• 2007

This paper discusses the acoustic performance of simple expansion chamber using computational fluid dynamics(CFD). The CFD model consists of an axisymmetric grid with a single period sinusoid of acceptable amplitude and duration imposed at the inlet boundary condition. The time history of the static pressure is recorded at two points, one in the inlet pipe and one point in outlet pipe. The time history of the static pressure is converted to the frequency domain using Fourier Transform and the transmission loss (TL) of the muffler is obtained from the ratio of the static pressure at the inlet and outlet pipe. The transmission loss of CFD result is compared with that of the computational acoustic analysis using the boundary element method (BEM). There are some differences in two results due to the pressure drop according to the inlet and outlet pipe length. Therefore, the effects of the pressure drop to the transmission loss have to be considered.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.445-450
• /
• 2011

금속분말을 연소시키기 위한 스월 연소기 설계의 기초단계로써 단일 접선 공급유로를 갖는 스월 혼합챔버를 제작하고 Paticle Image Velocimetry(PIV)를 사용하여 스월 혼합챔버의 내부 유동장 측정실험을 수행하였다. 상온의 공기를 작동유체로 사용하였으며 접선 공급유량이 증가하는 경우의 스월 혼합 챔버 내 축방향 및 접선방향 성분 속도를 획득하였다. 측정된 유동장을 바탕으로 스월유동과 역압력 구배로 인해 발생하는 외부 유입유동간의 혼합특성을 평가 하였다.

• 대한기계학회논문집
• /
• 제18권9호
• /
• pp.2423-2430
• /
• 1994

Several factors of the efficient combustion process are shape of combustion chamber, position of spark plug, turbulence flow and so on. the shape of combustion chamber and position of spark plug are constrained to geometrically, and then it could not make a change the shape easily. But the turlence flow in combustion chamber have a great influence on combustion phenomena, and which is much easier to control relatively. And since characteristics of turbulence flow would be very important to the stability of combustion and performances, This study is also essential to future engine-low emission and lean burn engine. This paper shows that the visualization of the turbulence flow of single cylinder engine by using 2way, $45^{\circ}$ inclined and 2 channel hot wire probe through the park plug hole. We also study the characteristics of turbulence flow by means of ensemble averaged mean velocity, turvulence intensity and integral length scale.

• 대한토목학회논문집
• /
• 제33권4호
• /
• pp.1455-1462
• /
• 2013

본 연구에서는 유공부 형상, 상대유수실 폭, 파형경사 등에 따른 유공케이슨의 소파특성을 2차원 및 3차원 실험을 통해 고찰하였다. 파랑이 직각으로 입사하는 경우, 유사한 유공율 조건에서 횡 slit이 종 slit에 비해 반사계수가 약간 작게 계측되었으나 그 차이는 크지 않았다. 그리고 파형경사가 큰 경우가 작은 경우에 비해 약간 낮은 반사계수를 보였다. 경사 입사파 조건에서도 유공율이 유사할 경우, 유공부 형상에 따른 제체 전면의 파고 차이는 거의 발생하지 않았다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제29회 추계학술대회논문집
• /
• pp.198-203
• /
• 2007

본 연구의 목표는 air core의 길이 조절이 가능한 스월인젝터의 음향학적인 감쇠기능을 통해 고주파 연소불안정을 억제하는 것이다. air core(길이, 형상, 부피)와 인젝터의 위치에 대한 음향학적인 감쇠 효과는 선행 연구를 통해 실험되었다. 이러한 결과들을 바탕으로 다중 인젝터들의 효과에 대한 연구를 진행하였다. 실험 결과로부터 각 모드의 배(anti-node)에 장착된 인젝터들의 수의 증가로 감쇠효과가 증가하는 것을 확인하였다. 또한 각 모드들의 배(anti-node)에 장착되어 동조된 인젝터들이 동시에 개별적인 모드 감쇠 성능을 보일 수 있음을 확인했다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권5호
• /
• pp.818-826
• /
• 2004

The spray-induced mixing characteristics and thermal decomposition of aqueous urea solution into ammonia have been studied to design optimum sizes and geometries of the mixing chamber in SCR(Selective Catalytic Reduction) system. The cold flow tests about the urea-injection nozzle were performed to clarify the parameters of spray mixing characteristics such as mean diameter and velocity of drops and spray width determined from the interactions between incoming air and injected drops. Discrete particle model in Fluent code was adopted to simulate spray-induced mixing process and the experimental results on the spray characteristics were used as input data of numerical calculations. The simulation results on the spray-induced mixing were verified by comparing the spray width extracted from the digital images with the simulated Particle tracks of injected drops. The single kinetic model was adopted to predict thermal decomposition of urea solution into ammonia and solved simultaneously along with the verified spray model. The hot air generator was designed to match the flow rate and temperature of the exhaust gas of the real engines The measured ammonia productions in the hot air generator were compared with the numerical predictions and the comparison results showed good agreements. Finally, we concluded that the design capabilities for sizing optimum mixing chamber were established.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.1371-1374
• /
• 1997

We had developed the on-line environmental monitoring system which has installed around Kori Nuclear Power Plants and will be taken the place of the existing system. The system consists of a main computer and 11 sets of radiation monitoring post equipments. Nal(Tl) scintillation detectro was adopted in addition to ion-chamber detector and implemented with DCU(Dose Conversion Unit) and SCA(Single Channel Analyzer). Compared with the existing system, it has revised feature in the radiation measurements which are detection of artificial radioactivity and 2-ways of the radiatiion detectors. The field test trsults show that the developed radiation detecting equipments can measure environmental radiation withn 5.0% of the theoretical value.

• 소음진동
• /
• 제9권4호
• /
• pp.738-746
• /
• 1999

The performance of muffler can be improved for a frequency range of interest by moving inlet and outlet locations. And optimal location of inlet and outlet can be determined to improve the acoustic performance. The optimum design using FEM, however, may take a very long time and be very hard to take inlet and outlet locations as design variables. In this paper, the acoustic performance of reactive type single expansion chamber muffler is predicted using higher order mode theory. The sensitivity analysis of transmission loss with respect to the location of inlet and outlet is suggested. And the acoustic power transmission coefficient for a frequency of interest is used as cost function. Optimum location of inlet and outlet is determined to minimize cost function by using SUMT algorithm.