• Journal of the Korean Solar Energy Society
• /
• v.39 no.1
• /
• pp.11-19
• /
• 2019

Spectroscopic ellipsometry is a powerful tool for analyzing optical properties of material. Ellipsometry measurement results is usually given by change of polarization state of probe light, so the measured result should be properly treated and transformed to meaningful parameters by transformation and modeling of the measurement result. In case of hydrogenated amorphous silicon, Tauc-Lorentz dispersion is usually used to model the measured ellipsometry spectrum. In this paper, modeling of spectroscopic ellipsometry result of hydrogenated amorphous silicon using Tauc-Lorentz dispersion is discussed.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.4
• /
• pp.101-104
• /
• 2018

An electric field was applied to a Mo conductive layer in the sandwiched structure of $glass/SiO_2/Mo/SiO_2/a-Si$ to induce Joule heating in order to generate the intense heat needed to carry out the crystallization of amorphous silicon. Polycrystalline silicon was produced via Joule heating through a solid state transformation. Blanket crystallization was accomplished within the range of millisecond, thus demonstrating the possibility of a new crystallization route for amorphous silicon films. The grain size of JIC poly-Si can be varied from few tens of nanometers to the one having the larger grain size exceeding that of excimer laser crystallized (ELC) poly-Si according to transmission electron microscopy. We report here the blanket crystallization of amorphous silicon films using the $2^{nd}$ generation glass substrate.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.4
• /
• pp.439-444
• /
• 2024

This study investigates the post-thermal treatment effects on the efficiency of silicon heterojunction solar cells, specifically examining the influence of annealing on p-type microcrystalline silicon oxide and ITO thin films. By assessing changes in carrier concentration, mobility, resistivity, transmittance, and optical bandgap, we identified conditions that optimize these properties. Results reveal that appropriate annealing significantly enhances the fill factor and current density, leading to a notable improvement in overall solar cell efficiency. This research advances our understanding of thermal processing in silicon-based photovoltaics and provides valuable insights into the optimization of production techniques to maximize the performance of solar cells.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.2
• /
• pp.56-59
• /
• 2001

Thin films of hydrogenated amorphous silicon (a-Si : H) of different compositions were deposited on Si(100) wafer and glass by RF plasma-enhanced chemical vapor deposition (PECVD). In the present work, we have investigated the effect of the If. power on the properties, such as optical band gap, transmittance and crystallinity, of crystalline silicon thin films. Raman data show that the material consists of an amorphous and crystalline phase for the co-presence of two peaks centered at 480 and 520cm$^{-1}$. X-ray spectra confirmed of crystallites with (111) orientation at 300w The transmittance of thin films was measured by UV-VIS spectrophotometer. In addition, Si-H chemical bondings were studied by Fourier Transform Infrared (FT-IR) spectroscopy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.366.1-366.1
• /
• 2014

The rare-earth oxides M2O3 (M=La, Pr, Gd) are good insulators due to their large band gap (3.9eV for Pr2O3, 5.6eV for Gd2O3), they have high dielectric constants (Gd2O3 K=16, La2O3 K=27, Pr2O3 K=26-30) and, compared to ZrO2 and HfO2, they have higher thermodynamic stability on silicon making them very attractive materials for high-K dielectric applications. Another attractive feature of some rare-earth oxides is their relatively close lattice match to that of silicon, offering the possibility of epitaxial growth and eliminating problems related to grain boundaries in polycrystalline films. Metal-organic chemical vapor deposition (MOCVD) has been preferred to PVD methods because of the possibility of large area deposition, good composition control and excellent conformal step coverage. Herein we report on the synthesis of rare-earth oxide complexes with designed alkoxide and aminoalkoxide ligand. These novel complexes have been characterized by means of FT-IR, elemental analysis, and thermogravimetric analysis (TGA).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1175-1180
• /
• 2003

Transformer Coupled Plasma Chemical Vapor Deposited (TCP-CVD) silicon nitride (SiNx) is widely used as a gate dielectric material for thin film transistors (TFT). This paper reports the SiNx films, grown by TCP-CVD at the low temperature (30$0^{\circ}C$). Experimental investigations were carried out for the optimization o(SiNx film as a function of $N_2$/SiH$_4$ flow ratio varying ,3 to 50 keeping rf power of 200 W, This paper presents the dielectric studies of SiNx gate in terms of deposition rate, hydrogen content, etch rate and leakage current density characteristics lot the thin film transistor applications. And also, this work investigated means to decrease the leakage current of SiNx film by employing $N_2$ plasma treatment. The insulator layers were prepared by two step process; the $N_2$ plasma treatment and then PECVD SiNx deposition with SiH$_4$, $N_2$gases.

• Korean Journal of Materials Research
• /
• v.30 no.12
• /
• pp.660-665
• /
• 2020

Silicon heterojunction solar cells can achieve high conversion efficiency with a simple structure. In this study, we investigate the passivation characteristics of VOx thin films as a hole-selective contact layer using ALD (atomic layer deposition). Passivation characteristics improve with iVoc (implied open-circuit voltage) of 662 mV and minority carrier lifetime of 73.9 µs after post-deposition annealing (PDA) at 100 ℃. The improved values are mainly attributed to a decrease in carbon during the VOx thin film process after PDA. However, once it is annealed at temperatures above 250 ℃ the properties are rapidly degraded. X-ray photoelectron spectroscopy is used to analyze the chemical states of the VOx thin film. As the annealing temperature increases, it shows more formation of SiOx at the interface increases. The ratio of V5+ to V4+, which is the oxidation states of vanadium oxide thin films, are 6:4 for both as-deposition and annealing at 100 ℃, and 5:5 for annealing at 300 ℃. The lower the carbon content of the ALD VOx film and the higher the V5+ ratio, the better the passivation characteristics.

• Current Photovoltaic Research
• /
• v.12 no.2
• /
• pp.41-47
• /
• 2024

CIGS solar cells are thin film solar cells that have excellent light absorption coefficient and can be manufactured with high efficiency through the use of low materials. In Korea, they must pass KS certification for home and commercial installation. KS C 8562 is a standard for evaluating the durability of CIGS and thin film amorphous silicon solar modules and deals with contents such as light, temperature, humidity, and mechanical durability. Unlike general crystalline silicon solar modules, the CIGS solar module has a different behavior of output change through these environmental tests, so if it shows 90% or more of the rated output suggested by the manufacturer after the final test, it is judged to be a suitable product. In this paper, the output before and after individual tests was measured through the test method of KS C 8562 to observe the output change and to discover the vulnerabilities of the CIGS solar module when exposed to various environments. Through this, it was confirmed that humidity exposure was the most vulnerable and that it had output recovery characteristics for light (visible light and ultraviolet rays). This study attempted to present the output behavior characteristics and data of the CIGS module at the time when the high efficiency thin film photovoltaic module market is expected to be created in the future.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.9-13
• /
• 2019

In this study, a miniature thin film-patterned heater was fabricated on a silicon substrate using semiconductor process technology and the thermal characteristics of the applied voltage, power, and temperature of the thin film heater were measured and analyzed. The temperature of the thin film pattern heater increased with increasing power, but the temperature increase rate was gradual at high power intervals. The characteristics of the high temperature section of the platinum thin film-patterned heater were analyzed using the heat resistance model under atmospheric and vacuum conditions. The thermal resistance measured in a vacuum atmosphere was 0.79 [K/mW] higher than the heat resistance value 0.69 [K/mW] in air. The temperature of the thin film pattern heater can be maintained at a low power in a vacuum rather than in air, and these results are expected to be utilized in the structural design of a thin film-patterned heater element.

• Journal of the Korean institute of surface engineering
• /
• v.33 no.2
• /
• pp.77-86
• /
• 2000

In this study effects of La starting compounds and substrates on the densification of (P $b_{0.92}$L $a_{0.05}$)Ti $O_3$ thin films were investigated. After the heat treatment on platinized silicon at $650^{\circ}C$ for 30min thickness of PLT(i) thin films (from La-isopropoxide) shrank by 27%, while 33% reduction occurred for PLT (a) thin films (from La-acetate). These PLT(i) films showed less densified surface microstructure compared to the PLT (a) . Lower shrinkage of the films on platinized silicon than on bare silicon (41% and 40% for PLT (i) and PLT (a) respectively) is attributed to the earlier development of crystallinity in the film, which arrests film densification. In order to maximize sintering before crystallization, heat treatment at $400^{\circ}C$ for 3 hours followed by $650^{\circ}C$ for 30 min was attempted. This method increased the shrinkage of the PLT (i) and PLT (a) films two times and 1.5 times as much as that observed for the films heat treated at $650^{\circ}C$ for 30min, respectively. FTIR results indicated that first pyrolysis in the film is associated with the burning of acetate ligands. Condensation reaction between OHs was found to occur preferentially between $350^{\circ}C$ and $450^{\circ}C$, whereas majority of polycondensation between ROH-OH appears to occur until $300^{\circ}C$ and be completed below $450^{\circ}C$.EX>.