• Journal of Navigation and Port Research
• /
• v.28 no.6
• /
• pp.503-507
• /
• 2004

We prepared EM wave absorbers by using recycled Sr ferrite for GHz frequency, and investigated the effects of carbon additions and preparation temperatures on their EM wave absorption properties. A Sr ferrite EM wave absorber with the ratio of Sr ferrite: silicon rubber: carbon = 80 : 13.6: 6.4 wt% prepared at 7$0^{\circ}C$ showed -24 dB at 9.4 GHz and -23 dB at 5.5 GHz for 2 mm and 3 mm thickness, respectively.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.4
• /
• pp.387-394
• /
• 2017

This paper develops a pump system for patient with chronic pain or cancer. The pump module is consists of two micro-valve and membrane. The micro-valve is operated by a solenoid. With two solenoid valves which are connected via a drug transport line, the inlet and outlet are completely blocked. A silicon rubber membrane located between the two valves makes the flow-rate constant without any backflow. This pump module can control the flow-rate of drugs by controlling the time that the valves are opened and closed. The reservoir consists of a drug chamber and a gas chamber. As the gas chamber encloses the drug chamber, propellant gas which is injected into the gas chamber pressurizes the drug chamber regardless of volume of the drug chamber. To design the pump module, analysis a constant efficiency test, and accuracy test for the pump module were conducted.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03b
• /
• pp.29-29
• /
• 2010

Surface contamination and leakage current have caused operating problems. A flashover in a substation may result in destruction of an insulator or many others electrical equipment. Engineering plastics have good characteristic (light weight, good productivity and little of void) as compare with epoxy or porcelain insulators. Outdoor insulator must have resistance to contamination. However, it isn't suited to outdoor insulator because it is not hydrophobic. RTV(Room temperature vulcanizing) has a good property of hydrophobic and micro-filler. nano-filler have characteristics of obstructing exothermic reaction. In order to reduce the incidence of insulator flashover and damage, the silicon rubber contained with micro, nano-filler coating on surface of engineering plastics. In this paper, it compares tracking resistance, leakage current of the engineering plastic coated RTV with that of non-coated engineering plastic. And filled-composites performed much better than non-filled composites.

• Fashion & Textile Research Journal
• /
• v.16 no.3
• /
• pp.434-445
• /
• 2014

The meaning of this research is to make recognition for necessity of ergonomic fashion design research. And the purpose is to provide the guidelines for ergonomic fashion product development. For this, literature research and analysis of empirical illustration of product design indicating ergonomics characteristic are implemented. Among the body-conscious active sportswear, cycle wear, swim suit, and skin scuba wet suit were selected and analyzed. Then they were explained according to the ergonomics characteristics arranged previously. Lastly, the features of ergonomic fashion design were arranged by composition elements of the clothing such as pattern, sewing, material and detail. The characteristics of ergonomic design derived from literature and advanced researches are efficiency, usability, functionality and safety. Through research and analysis, the characteristics of ergonomic fashion design are as followings. In pattern, it is related to the 3D structure division pattern, the reduction pattern design, the closing & opening part design for easy detachment, the receipt and the changeable design. In sewing, it is related to the use of latest sewing techniques and the finish using silicon or rubber band. In material, it is related to the use of high performance fabrics and the proper arrangement of these. In detail, it is related to the convenient detail, the storage detail, the adjustable detail, and the body protection detail.

• Journal of KSNVE
• /
• v.9 no.6
• /
• pp.1247-1258
• /
• 1999

This paper presents vibration control of a CD-ROM(compact disc-read only memory) drive feeding system consisting of a new type of CD-ROM mount using an electro-rheologocal(ER) fluid. Chemically treated starch particles and silicon oil are used for EF fluid, and its field-dependent yield stresses are experimentally distilled under both the shear and the flow modes. On the basis of the yield stress, an appropriate size of ER CD-ROM mount adapted to conventional feeding system is designed and manufactured. Vibration isolation performance of the proposed mount is evaluated in the frequency domain and compared with that of conventional rubber mount. The ER CD-ROM mount is then installed to the drive feeding system and the system equation of motion is derived. The skyhook controller is then incorporated with the fuzzy technique to improve the performance of ER CD-ROM mount. A set of fuzzy parameters and control rules are obtained from a relation between vertical displacement and pitching motion of the feedng system. Followingthe formulation of the fuzzy-skyhook controller, computer simulation is undertaken in order to evaluate vibration suppression of the CD-ROM drive feeding system subjected to various excitations.

• Proceedings of the SAREK Conference
• /
• 2005.11a
• /
• pp.323-328
• /
• 2005

The objective of this study is to analyze the cooling performance of an air- cooling system for telecommunication equipment. Temperature variation and capacity were measured in an actual unit for telecommunication equipment. In addition, the cooling performance was measured by installing a silicon rubber heater as a heat source in a cabinet. The standard thermal load for telecommunication equipment was approximately 293 W, and the maximum temperature of the heated surface was $64.5^{\circ}C$. The average and maximum temperatures of the heated surface were proportional to the inlet air temperature. When the heat load increased from 293 W to 400 W, the maximum temperature of the heated surface was higher than $64.5^{\circ}C$ even though the inlet air temperature decreased from 25 to $11^{\circ}C$.

• Journal of Powder Materials
• /
• v.25 no.5
• /
• pp.375-378
• /
• 2018

Conductive and dielectric SiC are fabricated using electroless plating of Ni-Fe films on SiC chopped fibers to obtain lightweight and high-strength microwave absorbers. The electroless plating of Ni-Fe films is achieved using a two-step process of surface sensitizing and metal plating. The complex permeability and permittivity are measured for the composite specimens with the metalized SiC chopped fibers dispersed in a silicone rubber matrix. The original non-coated SiC fibers exhibit considerable dielectric losses. The complex permeability spectrum does not change significantly with the Ni-Fe coating. Moreover, dielectric constant is sensitively increased with Ni-Fe coating, owing to the increase of the space charge polarization. The improvements in absorption capability (lower reflection loss and small matching thickness) are evident with Ni-Fe coating on SiC fibers. For the composite SiC fibers coated with Ni-Fe thin films, a -35 dB reflection loss is predicted at 7.6 GHz with a matching thickness of 4 mm.

• Journal of Aerospace System Engineering
• /
• v.11 no.6
• /
• pp.34-41
• /
• 2017

As an alternative of the existing honeycomb shock absorbing device, the new approach on shock absorbing design using the extrusion of hyper-viscoelastic material such as silicon rubber is studied in this paper. The strain energy and stress-strain characteristic of viscoelastic material at extrusion process through the metered orifice has a similarity with the honeycomb core for maximizing shock absorbing capability. And in order to evaluate the design feasibility of this device and to understand the shock absorbing mechanism of energy transformation, finite element analysis and quasi-static compression test of the multi-stage extrusion shock absorber are examined in this paper.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.779-782
• /
• 2000

Silicone rubbers are first silicone polymers and has named silicone from existence of Si-O bond similar to Keton. Silicon in organic compound has been called silicone, and linear or network polymers. Silicone rubbers have been used as an power insulator because they are well weather proof, ozone proof and have excellent electric characteristics, thermal stability, cold resistance and low surface energy. Especially, it is known that they have very excellent characteristics at 200[$^{\circ}C$]. For this study, we made silicone rubbers as specimens and we measured dielectric loss tangent due to applied voltage at temperature range 25[$^{\circ}C$] to 180[$^{\circ}C$] and frequency range 20[Hz] to 1${\times}$10$\^$6/[Hz] to examine dielectric properties. We measured dielectric loss tangent to study the insulation performance of silicone rubbers.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1998.10a
• /
• pp.63-65
• /
• 1998

1. Introduction : Atmospheric discharge of VOC-contaminated streams in chemical plants and air streams from chemical processes poses a serious environmental problem and entails large financial losses. Such emissions may be reduced by i) adsorption process, ii) absorption process and iii) incineration process. These processes only forbids the air pollutions. Throughout the recent decade, another technique-membrane process has emerged. The separation and recovery of organic vapors by membrane process may have great economic potential. Most of the published research works on the separation of organic vapors from air were performed using silicon rubber membranes. However, it is very difficult to fabricate very thin membranes with less than 1 $u m thickness. Plasma polymerization could be a good technique to generate a thin polymer film. The objective of this work is to find out the optimum condition of plasma polymerization for producing VOC separation membrane. For the objective, composite membranes are prepared through plasma polymerization of hexamethyldisiloxane onto porous substrates under different conditions. The membrane is then subjected to the permeation of permanent gases and VOCs to find the correlations between the physical properties of the penetrant and permeability and selectivity.