• International journal of advanced smart convergence
• /
• v.9 no.1
• /
• pp.177-184
• /
• 2020

In this paper, we studied to direction of arrival (DoA) estimation to use DoA and optimum weight algorithms in coherent interference channels. The DoA algorithm have been considerable attention in signal processing with coherent signals and a limited number of snapshots in a noise and an interference environment. This paper is a proposed method for the desired signal estimation using MUSIC algorithm and adaptive beamforming to compare classical subspace techniques. Also, the proposed method is combined the updated weight value with LCMV beamforming algorithm in adaptive antenna array system for direction of arrival estimation of desired signal. The proposed algorithm can be used with combination to MUSIC algorithm, linearly constrained minimum variance beamforming (LCMV) and the weight value method to accurately desired signal estimation. Through simulation, we compare the proposed method with classical direction of in order to desired signals estimation. We show that the propose method has achieved good resolution performance better that classical direction arrival estimation algorithm. The simulation results show the effectiveness of the proposed method.

• The Journal of the Acoustical Society of Korea
• /
• v.25 no.2E
• /
• pp.36-42
• /
• 2006

In this paper, a novel post processing using Wiener filtering technique is proposed to p rm further interference reduction in FDICA. Using the proposed method, the target signal components are remained with little attenuation while the interference components are drastically suppressed. The results of experiments show that the proposed method achieves a reduction of the residual crosstalk. Compared to the NLMS method, the proposed method has slightly better separation performance in SIR, and even requires much less computational complexity.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.11
• /
• pp.874-882
• /
• 2003

The condition assessment of engineering systems has increased in importance because the manpower needed to operate and supervise various plants has been reduced. Especially, induction motors are at the core of most engineering processes, and there is an indispensable need to monitor their health and performance. So detection and diagnosis of motor faults is a base to improve efficiency of the industrial plant. In this paper, a model-based fault detection system is developed for induction motors, using steady state vibration signals. Early various fault detection systems using vibration signals are a trivial method and those methods are prone to have missed fault or false alarms. The suggested motor fault detection system was developed using a model-based reference value. The stationary signal had been extracted from the non-stationary signal using a data segmentation method. The signal processing method applied in this research is FFT. A reference model with spectra signal is developed and then the residuals of the vibration signal are generated. The ratio of RMS values of vibration residuals is proposed as a fault indicator for detecting faults. The developed fault detection system is tested on 800 hp motor and it is shown to be effective for detecting faults in the air-gap eccentricities and broken rotor bars. The suggested system is shown to be effective for reducing missed faults and false alarms. Moreover, the suggested system has advantages in the automation of fault detection algorithms in a random signal system, and the reference model is not complicated.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.20 no.6
• /
• pp.15-21
• /
• 2010

In the recent years, various researches about the signal processing have been presented to improve the performance of power analysis. Among these signal processing techniques, the research about the signal compression is not enough than a signal alignment and a noise reduction; even though that can reduce considerably the computation time for the power analysis. But, the existing compression method can sometimes reduce the performance of the power analysis because those are the unsophisticated method not considering the characteristic of the signal. In this paper, we propose the new PCA (principal component analysis)-based signal compression method, which can block the loss of the meaningful factor of the original signal as much as possible, considering the characteristic of the signal. Also, we prove the performance of our method by carrying out the experiment.

• Journal of the Institute of Convergence Signal Processing
• /
• v.6 no.3
• /
• pp.143-147
• /
• 2005

Monitoring and diagnosis of the operating machines are very important for safety operation and maintenance in the industrial fields. These machines are most rotating machines and the diagnosis of the machines has been researched for long time. We can easily see the faulted signal of the rotating machines from the changes of the signals in frequency. The Linear Predictive Coding(LPC) is introduced for signal analysis in frequency domain. In this paper, we propose fault detection and diagnosis method using the Linear Predictive Coding(LPC) and residual signal energy. We applied our method to the induction motors depending on various status of faulted condition and could obtain good results.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.4
• /
• pp.1437-1445
• /
• 2014

In this paper a novel method for angular position determination using sensors with sin/cos output and without an excitation signal, is presented. The linearization of the sensor transfer characteristic and digitalization of the measurement results are performed simultaneously with a goal to increase the measurement resolution. This improvement is particularly important for low angular velocities, and can be used to increase the resolution of incremental Hall, magnetic and optical sensors. This method includes two phases of sin/cos signal linearization. In the first linearization phase the pseudo-linear signal is generated. The second linearization phase, executed by the two-stage piecewise linear ADC, is an additional linearization of the pseudo-linear signal. Based on the LabVIEW software simulations of the proposed method, the contribution of each processing phase to a final measurement error is examined. After the proposed method is applied within $2{\pi}$ [rad] range, the maximal nonlinearity is reduced from 0.3307 [rad] ($18.9447^{\circ}$) to $3{\cdot}10^{-4}$ [rad] ($0.0172^{\circ}$).

• Journal of the Korea Institute of Military Science and Technology
• /
• v.25 no.4
• /
• pp.347-354
• /
• 2022

The synthetic aperture radar(SAR) is an equipment that can acquire images in all weathers day and night based on radar signals. The on-board processor of satellite SAR generates transmission signal by digital signal processing, converts it into an analog signal and transmits to antenna. Until the transmission signal generated by on-board processor is output, the signal passes the transmission cables and analog devices. At this time, these hardware distort the signal and makes SAR performance worse. To improve the performance, pre-distortion technique is used. But, general pre-distortion using taylor series is not sufficient to compensate for the distortion. This paper suggests transmit signal design method with improved pre-distortion. This paper uses envelop sampling method and interpolation filter for frequency domain compensation. The proposed method accurately compensates the hardware distortion and reduces resource usage of FPGA. To analyze proposed method's performance, IRF characteristics are compared when the proposed method applies to signal with errors.

• Journal of Positioning, Navigation, and Timing
• /
• v.9 no.4
• /
• pp.337-345
• /
• 2020

In this paper, an efficient signal tracking method to simultaneously track both GPS L1 C/A and Galileo E1B CBOC(6,1,1/11) using a low cost GPU is proposed. In the existing method that each GNSS signal is processed within 1 ms, more than 2 ms processing time is required in GPU to process 4 ms CBOC signal. It means that real time operation is possible if only Galileo E1B CBOC signal is concerned. But when both GPS C/A and Galileo CBOC is required, it cannot process GPS C/A signal in real time. To process 1 ms GPS C/A and 4 ms Galileo CBOC signal in real time, 4 ms Galileo CBOC signal is divided into 4 by 1 ms signal block in the proposed method. Specially, a buffer that simultaneously manages 1 ms and 4 ms signals is designed. In addition, a module that accumulates the 1 ms correlation value of the Galileo CBOC by 4 ms and passes it to the PLL and DLL is implemented. The operation and performance are evaluated with real measurements in the GPU based SDR. The experimental results show that tracking of more than 16 satellites of GPS C/A and Galileo E1B is possible using the proposed method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.1
• /
• pp.20-27
• /
• 2010

In this paper, we presented a signal model of STAP and actual environment of clutter. The novel estimation method of clutter covariance matrix using median value is proposed to overcome serious performance degradation after NHD in nonhomogeneous clutter. Eigen value characteristic is improved through diagonal loading. Target detection ability and SINR loss of the proposed method though MSMI statistic is also compared with conventional method using average value. The simulation results, confirm the proposed method has better performance than others.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.30B no.12
• /
• pp.31-39
• /
• 1993

In the playback signal processing of a digital magnetic recording system, the major signal processing processes consist of pulse equalization. pulse detection, clock recovery, and data recovery. Equalizer which compensates interference occurrde between pulses recorded in high density on a magnetic media is realized by pulse slimming method, and pulse detection by a integrating detector. Clock recovery from the detector output was accomplished by using PLL. and data recovery to reduce noise effects was carried out by utilizing the three sampling clocks recovered in clock recovery process. In this paper these processes are implemented in hardware and its performance is evaluated by experimenting with a commercial DAT. It was found that the playback signal processor proposed is suitable to the practical high density magnetic recording system.