• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.261-263
• /
• 2002

CMOS devices have scaled down to sub-50nm gate to achieve high performance and high integration density. Key challenges with the device scaling are non-scalable threshold voltage( $V^{th}$ ), high electric field, parasitic source/drain resistance, and $V^{th}$ variation by random dopant distribution. To solve scale-down problem of conventional structure, a new structure was proposed. In this paper, we have investigated double-gate MOSFET structure, which has the main-gate and the side-gates, to solve these problem.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.79-80
• /
• 2006

From a viewpoint of heat stress at high temperatures and contact thermal resistance, it is confirmed that the optimal structure is the skeleton structure using Cu substrate on the cooling side, which has excellent heat conductivity and the optimal installation method is to adopt a carbon sheet and a mica sheet to the high temperature side, where Si grease is applied to the low temperature side, under pressurized condition. The power of the developed modules indicated 0.5W in an $FeSi_2$ module and 3.8 W with a SiGe module at 823K, respectively.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.651-656
• /
• 2006

A performance analysis model has been developed for fin-tube type heat exchanger for $CO_2$ heat pump. The model uses the tube-by-tube method Because air-side thermal resistance has a great portion among total thermal resistances, it is important to understand air-side heat transfer characteristics. The air-side heat transfer correlation has been proposed from experiments using water. The developed model was confirmed by experimental results and can be used for the performance analysis of heat exchanger.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.5
• /
• pp.559-566
• /
• 2014

Plasma coatings have been conducted to improve the mechanical properties of thermal resistance, wear resistance, corrosion resistance and thermal shock with respect to Great-Bar which is used as a carrier device for ironstone sintering under $700^{\circ}C$. The surface coatings on the upper side of the Great-Bar exposed on extreme environments of high temperature, severe wear, corrosion and thermal shock extended the life time due to the barrier coating layer. $Al_2O_3$, $Cr_2O_3$, WC coatings were applied to Great-Bar and their mechanical and chemical properties are analyzed by several experimental tests such as thermal resistance, wear resistance, corrosion resistance and thermal shock resistance. It shows excellent advantages with respect to wear, thermal shock and corrosion.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.05a
• /
• pp.79-84
• /
• 2004

Initial hull form of 10 G/T and 40 knots class coastal patrol boat is newly developed. The resistance performances are experimentally and numerically investigated by model test at high speed circulating water channel(CWC) and CFD technique. The effect of a fin attached at hull side and initial trim are studied together. Wave patterns are observed to make clear the relation between the resistance performance and the wave characteristics. it can be found that the initial trim plays a role to increase the resistance performance above a certain velocity.

• Journal of the Korea Convergence Society
• /
• v.5 no.2
• /
• pp.19-23
• /
• 2014

In this study, the air resistance is studied by using flow analysis near automotive body due to the its shape. Flow velocities of airs entering into inlet plane are two kinds of 70 km/h and 100 km/h. Air resistance in case of high speed driving(100 km/h) becomes higher than regular speed driving(70 km/h) and the resistance in case of the car with wider cross section at front side becomes higher than narrower cross section. By using this analysis result, the shape of automotive body can be effectively designed in order to reduce the air resistance.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.04a
• /
• pp.151-154
• /
• 2007

To build up the green roofs, it must not adverse effect to durability and structural safety. That is conducted by safety system which consist of waterproofing to form basically, root barrier to protect the waterproofing. The reason why root barrier form is to protect the penetration force of root growth and the root could penetrate concrete surface, move inward so far. It may cause shorten the life span on concrete structure. For this problem, government constantly demand the solution to form the root barrier for waterproofing and concrete structure before the building is service. However, the technical action is not fully prepared. Therefore, in this study, we would like to suggest the workability and suitability of the copper plate to solve not only the side of waterproofing but also root barrier for green roof system and exhibit the mechanism for root penetration resistance and corrosion resistance.

• International Journal of Concrete Structures and Materials
• /
• v.11 no.1
• /
• pp.29-43
• /
• 2017

This study investigates the blast resistance of fiber-reinforced cementitious composite (FRCC) panels, with fiber volume fractions of 2%, subjected to contact explosions using an emulsion explosive. A number of FRCC panels with five different fiber mixtures (i.e., micro polyvinyl alcohol fiber, micro polyethylene fiber, macro hooked-end steel fiber, micro polyvinyl alcohol fiber with macro hooked-end steel fiber, and micro polyethylene fiber with macro hooked-end steel fiber) were fabricated and tested. In addition, the blast resistance of plain panels (i.e., non-fiber-reinforced high strength concrete, and non-fiber-reinforced cementitious composites) were examined for comparison with those of the FRCC panels. The resistance of the panels to spall failure improved with the addition of micro synthetic fibers and/or macro hooked-end steel fibers as compared to those of the plain panels. The fracture energy of the FRCC panels was significantly higher than that of the plain panels, which reduced the local damage experienced by the FRCCs. The cracks on the back side of the micro synthetic fiber-reinforced panel due to contact explosions were greatly controlled compared to the macro hooked-end steel fiber-reinforced panel. However, the blast resistance of the macro hooked-end steel fiber-reinforced panel was improved by hybrid with micro synthetic fibers.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.6
• /
• pp.193-195
• /
• 2009

This paper aims to develop a low gate source voltage ($V_{gs}$) N-LDMOS element that is fully operational at a CMOS Logic Gate voltage (3.3 or 5 V) realized using the 0.35 μm BCDMOS process. The basic structure of the N-LDMOS element presented here has a Low $V_{gs}$ LDMOS structure to which the thickness of a logic gate oxide is applied. Additional modification has been carried out in order to obtain features of an improved breakdown voltage and a specific on resistance ($R_{sp}$). A N-LDMOS element can be developed with improved features of breakdown voltage and specific on resistance, which is an important criterion for power elements by means of using a proper structure and appropriate process modification. In this paper, the structure has been made to withstand the excessive electrical field on the drain side by applying the double gate oxide structure to the channel area, to improve the specific on resistance in addition to providing a sufficient breakdown voltage margin. It is shown that the resulting modified N-LDMOS structure with the feature of the specific on resistance is improved by 31%, and so it is expected that optimized power efficiencies and the size-effectiveness can be obtained.

• Journal of Surface Science and Engineering
• /
• v.53 no.1
• /
• pp.29-35
• /
• 2020

In this study, five different specimen preparation methods were introduced and their advantages and disadvantages were presented. One of them, an epoxy mounting method has advantages of constant exposure area, ease of surface preparation without touching the specimen surface during polishing or cleaning, use of small amount of material and ease of specimen reuse by polishing or etching. However, in order to eliminate unexpected errors resulting from preferable reaction at the specimen/epoxy interface and contact resistance between the specimen and copper conducting line for electrical connection, it is recommended to cover the wall side of the specimen with porous anodic oxide films and to remain the contact resistance lower than 1 ohm. The increased contact resistance between the specimen and Cu conducting line appeared to result in increases of anodizing voltage and solution temperature during anodizing by which thickness and hardness of anodizing film on Al2024 alloy were drastically decreased and color of the films became more brightened.