• Journal of the Korean Vacuum Society
• /
• v.5 no.3
• /
• pp.239-244
• /
• 1996

We firstly report that formation of $SiO_2$ layer on Si surface can be effectively prevented by flowing the $Si_2H_6$ gas during the heating-up procedure for amorphous Si depositions. In this way, amorphously deposited Si layer onto crystalline Si substrates can be grown epitaxially during the post-deposition heat treatments. The suppression of surface $SiO_2$ can be explained in terms of adsorption of SiHx adspecies, instead of oxygen from residual gases in the reactors, to Si surfaces after desorption of hydrogen from H-passivated Si surfaces. Employing $Si_2H_6$ flowing and soild phase epitaxial growth, high-quality epitaxial Si layer can be obtained at low temperatures below $600^{\circ}C$ without conventional high temperature cleaning procedures.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.119-119
• /
• 2015

Ion beam sputtering has been widely used in Secondary Ion Mass Spectrometry (SIMS), X-ray Photoelectron Spectroscopy (XPS), and Auger Electron Spectroscopy (AES) for depth profile or surface cleaning. However, mainly due to severe matrix effects such as surface composition change from its original composition and damage of the surface generated by ion beam bombardment, conventional sputtering skills using mono-atomic primary ions with energy ranging from a few hundred to a thousand volts are not sufficient for the practical surface analysis of next-generation organic/inorganic device materials characterization. Therefore, minimization of the surface matrix effects caused by the ion beam sputtering is one of the key factors in surface analysis. In this work, the electronic structure of a $Ta_2O_5$ thin film on $SiO_2/Si$ (100) after Ar Gas Cluster Ion Beam (GCIB) sputtering was investigated using X-ray photoemission spectroscopy and compared with those obtained via mono-atomic Ar ion beam sputtering. The Ar ion sputtering had a great deal of influence on the electronic structure of the oxide thin film. Ar GCIB sputtering without sample rotation also affected the electronic structure of the oxide thin film. However, Ar GCIB sputtering during sample rotation did not exhibit any significant transition of the electronic structure of the $Ta_2O_5$ thin films. Our results showed that Ar GCIB can be useful for potential applications of oxide materials with sample rotation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.2
• /
• pp.111-117
• /
• 2008

We have studied surface roughness, contamination of impurity, bonding with some gas element, reflectance and zeta potential on masks to be generated or changed during photolithography/dry or wet etching process. Mask surface roughness was not changed after photolithography/dry etching process. But surface roughness was changed on some area under MoSi film of Cr/MoSi/Qz. There was not detected any impurity on mask surface after plasma dry etching process. Reflectance of mask was increased after variable plasma etching treatment, especially when mask was treated with plasma including $O_2$ gas. Blank mask was positively charged when the mask was treated with Cr plasma etching gas($Cl_2:250$ sccm/He:20 $sccm/O_2:29$ seem, source power:100 W/bias power:20 W, 300 sec). But this positive charge was changed to negative charge when the mask was treated with $CF_4$ gas for MoSi plasma etching, resulting better wet cleaning. There was appeared with negative charge on MoSi/Qz mask treated with Cr plasma etching process condition, and this mask was measured with more negative after SC-1 wet cleaning process, resulting better wet cleaning. This mask was charged with positive after treatment with $O_2$ plasma again, resulting bad wet cleaning condition.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.91-96
• /
• 2001

Ultrafine particles have been widely used in many high technology industrial areas. The spherical nonagglomerated and uniform nanometer-size $SiO_{2}$ particles are synthesized by the injection of TEOS vapor, ions and reaction gas in furnace. Ions were generated by Corona discharge electrode and these ions charge $SiO_{2}$ particles. As a result, spherical, nonagglomerated and ultrafine particles are generated in various conditions, it's morphology, charging portion and size distribution are examined by using TEM, ESP and SMPS. As the applied voltage of electrode changes from 0 kV to 5.0 kV, it is observed that the mean diameter of $SiO_{2}$ particle decreases from 94 nm to 42 nm.

• Journal of the Korean Vacuum Society
• /
• v.5 no.3
• /
• pp.223-228
• /
• 1996

$SiO_2$ insulator layers on InSb have been prepared by remote PECVD system a low temperature below $200^{\circ}C$. The effects of deposition pressure, temperature, and gas flow ratio on the physical and electrical characteristics of the $SiO_2$ were studied. The InSb MIS device using $SiO_2$ was fabricated and measured its current-voltage and capacitance-voltage characteritance-voltage charateristics at 77K. The films evaluated Auger electron spectroscopy showed that composition atoms were distributed uniformaly throughout the oxide film and the outdiffusion of substrate atoms into the oxide were few. The leakage current density of the MIS device was about 6.26nA/$\textrm{cm}^2$ at 0.75MV/cm , and the breakdown voltage was about 1MV/cm. The interface-stage density at mid-bandgap extracted from 1MHz C-V measurement was $54\times 10^{11}\textrm{cm}^2-2V^{-1}$.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.8
• /
• pp.63-70
• /
• 1992

Deposition properties and film characteristics of Remote PECVD silicon dioxide were investigated. Using $N_{2}O/SiH_{4}$, the effects of changing the process conditions` the pressure, the substrate temperature, and the gas mixing ration, on the film quality were observed. A comparison of film qualites of the Remote PECVD SiO$_2$ with that of a Direct PECVD SiO$_2$ was made. The experimental results show that the Remote PECVD SiO$_2$ has better electrical, physical, and annealing properties than the Direct PECVD oxide.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.298-301
• /
• 2000

We investigated the etch rate of SiO$_2$ in E-ICP, ICP system and the addition gas (O$_2$H$_2$) effect on SiO$_2$ etch characteristics. In all conditions, E-ICP shows higher etch rate than ICP. Small amount of O$_2$ addition increase F atom and O$\^$*/ concentration. at optimized condition (30％ O$_2$ in CF$_4$, 70Hz) E-ICP system shows highest etch rate (about 6000${\AA}$). H$_2$addition in CF$_4$ Plasma make abrupt decrease Si etch rate and moderate decrease SiO$_2$ etch rate.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.5
• /
• pp.669-673
• /
• 2002

Ni catalyst (Ni: 15 wt%) supported on precalcined SiO2 has been investigated in reforming reactions of methane to synthesis gas. The catalyst exhibited fairly good activity and stability in partial oxidation of methane (POM), whereas it deactivated in steam reforming of methane (SRM). Pulse reaction results of CH4, O2, and CH4/O2 revealed that Ni/SiO2 has high capability to dissociate methane. The results also revealed that both CH4 and O2 are activated on the surface of metallic Ni, and then surface carbon species react with adsorbed oxygen to produce CO and CO2 depending on the bond strength of the oxygen species on the catalyst surface.

• The Korean Journal of Ceramics
• /
• v.1 no.3
• /
• pp.147-151
• /
• 1995

Porous composite of $Al_2O_3$ and AIN based mullite and SiC can be prepared by alumium reaction synthesis and atmosphere controllied sintering in order to improve the durability of a gas filter body. The porous $Al_2O_3$-AIN-mullite, which has a strength of 168 kg/$\textrm{cm}^2$ and porosity of 51.59%, could be obtained by stmospheric firing at $1600^{\circ}C$ and the porous $Al_2O_3$-AIN-SiC with a porosity of 33% and strength of 977 kg/$\textrm{cm}^2$, could also be prepared. The average pore size has been changed from 0.2$\mu\textrm{m}$ in a reduction atmosphere and to 2$\mu\textrm{m}$ in an air atmosphere, respectively.

• Korean Journal of Materials Research
• /
• v.20 no.4
• /
• pp.223-227
• /
• 2010

Recently, one-dimensional semiconducting nanomaterials have attracted considerable interest for their potential as building blocks for fabricating various nanodevices. Among these semiconducting nanomaterials,, $SnO_2$ nanostructures including nanowires, nanorods, nanobelts, and nanotubes were successfully synthesized and their electrochemical properties were evaluated. Although $SnO_2$ nanowires and nanobelts exhibit fascinating gas sensing characteristics, there are still significant difficulties in using them for device applications. The crucial problem is the alignment of the nanowires. Each nanowire should be attached on each die using arduous e-beam or photolithography, which is quite an undesirable process in terms of mass production in the current semiconductor industry. In this study, a simple process for making sensitive $SnO_2$ nanowire-based gas sensors by using a standard semiconducting fabrication process was studied. The nanowires were aligned in-situ during nanowire synthesis by thermal CVD process and a nanowire network structure between the electrodes was obtained. The $SnO_2$ nanowire network was floated upon the Si substrate by separating an Au catalyst between the electrodes. As the electric current is transported along the networks of the nanowires, not along the surface layer on the substrate, the gas sensitivities could be maximized in this networked and floated structure. By varying the nanowire density and the distance between the electrodes, several types of nanowire network were fabricated. The $NO_2$ gas sensitivity was 30~200 when the $NO_2$ concentration was 5~20ppm. The response time was ca. 30~110 sec.