• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.242-243
• /
• 2007

Highly transparent conducting aluminum-doped zinc oxide (AZO) thin films were deposited on Corning glass substrate using an Nd:YAG pulsed laser deposition technology. AZO thin films deposited with 650nm thickness showed the best electrical properties of the electrical resistivity of $4.6{\times}10^{-4}[{\Omega}{\cdot}cm]$, a carrier concentration of $9.3{\times}10^{20}[cm^{-3}]$, and a carrier mobility of $31[cm^2/V{\cdot}s]$. Besides, the optical transmittance spectra in visible region (200-800nm) of AZO thin films show an high average transmittance over 90%.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.298-301
• /
• 1988

In this paper, we describes Faraday effect of BSO and ZnSe single crystals. By using intensity modulation, we detected. Faraday angle of light beam in these crystals and our current measurement system shows excellent linear characteristics by setting up circular core on a conductor.

• Resources Recycling
• /
• v.7 no.2
• /
• pp.39-45
• /
• 1998

We smelted thc pellets made by mixing the distilled carbon from wlISte Lires, LD converter dust and slag with reduction process in the revcrberatory furnace. Thc obtained results are as follows 1) The removal mte of zinc appears above 97% after T reducing the pellets at $1300^{\circ}C$ for Ihr and the zinc content in the residue are 0.1~D.2%. 2) Under the mixing condition of 500 g LD dust. 150-200 g LD slag and 30-50 g distilled carbon of waste lires the removal raho of zinc shows above 95%, while t the 50-60% Fe remains in the residue. 3) After smelting at $1350^{\circ}C$ for 3hrs, the recovery ratio of pig iron reduced from lhe p pellets containing 15-20% LD slag and 4.1-7.2% distilled carbon of waste tires appears in the range of 89.3-92%. 4) Tbe c chemical composition of the recovered pig iron is 1.7%C, O.05%P, 0.05%S and balance Fe. 5) Tbe recovered dust from the d dust collcctor alter finishing the reduction rcaction appears as a crude zinc oxide conLaining 60% zinc.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.27.2-27.2
• /
• 2010

In recent years, there is a strong requirement of low cost, stable microelectro mechanical systems (MEMS) for resonators, microswitches and sensors. Most of these devices consist of freely suspended microcantilevers, which are usually made by the etching of some sacrificial materials. Herein, we have attempted to use Si nanowires, inherited from the parent Si wafer, as a sacrificial material due to its porosity, low cost and ease of fabrication. Prior to the fabrication of the Si nanowires silver nanoparticles were continuously formed on the surface of Si wafer. Vertically aligned Si nanowires were fabricated from the parent Si wafers by aqueous chemical route at $50^{\circ}C$. Afterwards, the morphological and structural characteristics of the Si nanowires were investigated. The morphology of nanowires was strongly modulated by the resistivity of the parent wafer. The 3-step etching of nanowires in diluted KOH solution was carried out at room temperature in order to control the fast etching. A layer of $Si_3N_4$ (300 nm) was used for the selective fabrication of nanowires. Finally, a freely suspended bridge of zinc oxide (ZnO) was fabricated after the removal of nanowires from the parent wafer. At present, we believe that this technique may provide a platform for the inexpensive fabrication of futuristic MEMS.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.16.1-16.1
• /
• 2009

We have fabricated solution processed oxide semiconductor active layer for thin film transistors (TFTs). The oxide semiconductor layers were prepared by ink-jet printing the sol-gel precursor solution based on doped-ZnO. Inorganic ZnO-based thin films have drawn significant attention as an active channel layer for TFTs applications alternative to conventional Si-based materials and organic semiconducting materials, due to their wide energy band gap, optical transparency, high mobility, and better stability. However, in spite of such excellent device performances, the fabrication methods of ZnO related oxide active layer involve high cost vacuum processes such as sputtering and pulsed laser deposition. Herein we introduced the ink-jet printing technology to prepare the active layers of oxide semiconductor. Stable sol-gel precursor solutions were obtained by controlling the composition of precursor as well as solvents and stabilizers, and their influences on electrical performance of the transistors were demonstrated by measuring electrical parameters such as off-current, on-current, mobility, and threshold voltage. Microstructure and thermal behavior of the doped ZnO films were investigated by SEM, XRD, and TG/DTA. Furthermore, we studied the influence of the ink-jet printing conditions such as substrate temperature and surface treatment on the microstructure of the ink-jet printed active layers and electrical performance. The mobility value of the device with optimized condition was about 0.1-1.0 $cm^2/Vs$ and the on/off current ratio was about $10^6$. Our investigations demonstrate the feasibility of the ink-jet printed oxide TFTs toward successful application to cost-effective and mass-producible displays.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.11
• /
• pp.864-868
• /
• 2010

Among LTCC material for substrate, the crystallized anorthite system was mainly studied as high strength material. However, specific factors that have affected on strength of material were studied insufficiently on anorthite system. In this study, the composition of anorthite glass was Ca-Al-Si-Zn-O. The changes of phase and microstructure were observed with the amount and the particle size of glass and the sintering temperature. It was studied that the factors affected on the strength of material. Phases of anorthite and $ZnAl_2O_4$ were formed with the increase of sintering temperature. The $Al_2O_3$ phase was increased with $Al_2O_3$ amount, acted as filler, and the strength of material is increased with $Al_2O_3$ phase. But phases of anorthite and $ZnAl_2O_4$ didn't affect on the strength of material. In the case of 60 vol% glass amounts and below $3.2\;{\mu}m$ of glass particle size, the strength of material was decreased. It is thought that the decrease of strength was due to non-homogeneous mixing between glass powder and filler.

• Economic and Environmental Geology
• /
• v.42 no.3
• /
• pp.177-193
• /
• 2009

The Samgwang deposit consists of eight massive mesothermal quartz veins that filled NE and NW-striking fractures along fault zones in Precambrian granitic gneiss of the Gyeonggi massif. The mineralogy and paragenesis of the veins allow two separate discrete mineralization episodes(stage I=quartz and calcite stage, stage II-calcite stage) to be recognized, temporally separated by a major faulting event. The ore minerals are contained within quartz and calcite associated with fracturing and healing of veins that occurred during both mineralization episodes. The hydrothermal alteration of stage I is sericitization, chloritization, carbonitization, pyritization, silicification and argillization. Sericitic zone occurs near and at quartz vein and include mainly sericite, quartz, and minor illite, carbonates and chlorite. Chloritic zone occurs far from quartz vein and is composed of mainly chlorite, quartz and minor sericite, carbonates and epidote. Fe/(Fe+Mg) ratios of sericite and chlorite range 0.45 to 0.50(0.48$\pm$0.02) and 0.74 to 0.81(0.77$\pm$0.03), and belong to muscovite-petzite series and brunsvigite, respectiveIy. Calculated $Al_{IV}$-FE/(FE+Mg) diagrams of sericite and chlorite suggest that this can be a reliable indicator of alteration temperature in Au-Ag deposits. Calculated activities of chlorite end member are $a3(Fe_5Al_2Si_3O_{10}(OH)_6$=0.0275${\sim}$0.0413, $a2(Mg_5Al_2Si_3O_{10}(OH)_6$=1.18E-10${\sim}$7.79E-7, $a1(Mg_6Si_4O_{10}(OH)_6$=4.92E-10${\sim}$9.29E-7. It suggest that chlorite from the Samgwang deposit is iron-rich chlorite formed due to decreasing temperature from high temperature(T>450$^{\circ}C$). Calculated ${\alpha}Na^+$, ${\alpha}K^+$, ${\alpha}Ca^{2+}$, ${\alpha}Mg^{2+}$ and pH values during wallrock alteration are 0.0476($400^{\circ}C$), 0.0863($350^{\circ}C$), 0.0154($400^{\circ}C$), 0.0231($350^{\circ}C$), 2.42E-11($400^{\circ}C$), 7.07E-10($350^{\circ}C$), 1.59E-12($400^{\circ}C$), 1.77E-11($350^{\circ}C$), 5.4${\sim}$6.4($400^{\circ}C$), 5.3${\sim}$5.7($350^{\circ}C$)respectively. Gain elements(enrichment elements) during wallrock alteration are $TiO_2$, $Fe_2O_3(T)$,CaO, MnO, MgO, As, Ag, Cu, Zn, Ni, Co, W, V, Br, Cs, Rb, Sc, Bi, Nb, Sb, Se, Sn and Lu. Elements(Ag, As, Zn, Sc, Sb, Rb, S, $CO_2$) represents a potential tools for exploration in mesothermal and epithermal gold-silver deposits.

• Journal of the Korean Ceramic Society
• /
• v.26 no.6
• /
• pp.829-835
• /
• 1989

Devitrifing solder glasses in a specific group of glass ceramic materials are extensively used in hermetically sealing alumina electronics packages. Preferred frit glass compositions of this study consist of 37~40wt% PbO, 35~40wt% ZnO, 18~20wt% B2O3, 1~3wt% SiO2, 0~6wt% TiO2. The coated frit glasses crystallize during firing and form a strong hermetic seal. DTA and X-ray diffraction were used to characterize crystallization of the glass frit. Frit seal containing 2wt% TiO2 has crystallization temperature of 550~57$0^{\circ}C$ with surface nucleation. Frit seal containing 6wt% TiO2 has crystallization temperature of 515~5$25^{\circ}C$ with bulk nucleation, and the main crystalline phase was perovskite lead titanate having minus expansion coefficient. The average activation energy for the crystallization calculated from Ozawa equation was 65$\pm$10kcal/mol.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.157-157
• /
• 2009

$BaTiO_3$를 기본조성으로 하는 PTC 써미스터는 Curie 온도이상에서 저항이 급격히 상승하는 반도성 전자세라믹스로서 degaussing 소자, 정온 발열체, 온도센서, 전류 제한 소자 등 상업적으로 폭넓게 사용되고 있다. 본 소자는 소결온도, 소결 및 열처리 분위기, 불순물, 첨가제 등의 제조공정상의 인자들과 기공률, 결정립 크기 등이 복합적으로 작용하여 PTCR 특성이 크게 영향을 받기 때문에 제조하기에 무척 까다로운 소자로 알려져 있다. 특히 과전류 보호 소자용으로 사용하기 위해서는 상온 비저항을 크게 낮추어야 하며 이에 대한 연구가 계속 진행되고 있다. 따라서 본 연구에서는 SiO2을 0.5~10 at%로 달리한 조성으로 환원 분위기에서 소결하고 공기 중에서 재산화 처리하여 재료의 PTC 특성에 어떠한 영향을 미치는지 분석하였다. 소정의 조성을 선택하여 $1180^{\circ}C{\sim}1240^{\circ}C$에서 2시간 동안 환원분위기에서 소결하고, $800^{\circ}C$에서 1 시간 공기 중에서 재산화 처리한 후 R-T 특성을 측정하여 SiO2 함량에 따른 PTC 특성을 분석하였다. 그 결과 SiO2의 함량이 증가할수록 상온 저항은 낮아지다가 3.0 at% 이상으로 첨가할 경우 급격히 상승하는 경향을 나타내었다. 특히 SiO2를 1.0~3.0 at% 일 때 우수한 PTC 특성을 가졌다. $1180^{\circ}C$에서는 소결 밀도가 낮아 상온 비저항이 크게 높았지만, $1200^{\circ}C{\sim}1220^{\circ}C$에서는 정상 입성장이 나타나면서 일반적인 PTC 특성을 가졌지만, $1240^{\circ}C$ 이상에서는 공정 액상이 형성되어 비정상 입성장이 일어나 상온 비저항이 크게 낮아졌다. 한편 점핑비-log(Rmax/Rmin)는 SiO2 함량이 증가할수록 높아지다가 3.0 at% 이상에서는 낮아짐을 확인하였다.

• Restorative Dentistry and Endodontics
• /
• v.33 no.4
• /
• pp.369-376
• /
• 2008

The aim of this study was to compare the compositions and cytotoxicity of white ProRoot MTA (white mineral trioxide aggregate) and 3 kinds of Portland cements. The elements, simple oxides and phase compositions of white MTA (WMTA), gray Portland cement (GPC), white Portland cement (WPC) and fast setting cement (FSC) were measured by inductively coupled plasma atomic emission spectrometry (ICP-AES), X-ray fluorescence spectrometry (XRF) and X-ray diffractometry (XRD). Agar diffusion test was carried out to evaluate the cytotoxicity of WMTA and 3 kinds of Portland cements. The results showed that WMTA and WPC contained far less magnesium (Mg), iron (Fe), manganese (Mn), and zinc (Zn) than GPC and FSC. FSC contained far more aluminum oxide ($Al_2O_3$) than WMTA, GPC, and WPC. WMTA, GPC, WPC and FSC were composed of main phases. such as tricalcicium silicate ($3CaO{\cdot}SiO_2$), dicalcium silicate ($2CaO{\cdot}SiO_2$), tricalcium aluminate ($3CaO{\cdot}Al_2O_3$), and tetracalcium aluminoferrite ($4CaO{\cdot}Al_2O_3{\cdot}Fe_2O_3$). The significance of the differences in cellular response between WMTA, GPC, WPC and FSC was statistically analyzed by Kruskal-Wallis Exact test with Bonferroni' s correction. The result showed no statistically significant difference (p > 0.05). WMTA, GPC, WPC and FSC showed similar compositions. However there were notable differences in the content of minor elements. such as aluminum (Al), magnesium, iron, manganese, and zinc. These differences might influence the physical properties of cements.