• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.252-252
• /
• 2009

In this work, the nanocrystalline ZnO/polycrystalline (poly) aluminum nitride (AlN)/Si structure was fabricated for humidity sensor applications based on surface acoustic wave (SAW). In this structure, the ZnO film was used as sensing material layer. These ZnO and AlN(0002) were deposited by so-gel process and a pulse reactive magnetron sputtering, respectively. These experimental results showed that the obtained SAW velocity on AlN film was about 5128 m/s at $h/\lambda$=0.0125 (h and $\lambda$ is thickness and wavelength, respectively). For ZnO sensing layers coated on AlN, films have hexagonal wurtzite structure and nanometer particle size. The crystalline size of ZnO films annealed at 400, 500, and 600 $^{\circ}C$ is 10.2, 29.1, and 38 nm, respectively. Surface of the film exhibits spongy which can adsorb steam in the air. The best quality of the ZnO film was obtained with annealing temperature at 500 $^{\circ}Cis$. The change in frequency response (127.9~127.85 MHz) of the SAW humidity sensor based on ZnO/AlN structure was measured along the change in humidity (41~69%). The structural properties of thin films wereinvestigated by XRD and SEM.

• Transactions on Electrical and Electronic Materials
• /
• 제15권6호
• /
• pp.291-296
• /
• 2014

In recent years, researchers have extensively investigated polymers filled with inorganic nanoparticles because these materials present improved physical properties relative to those of conventional unfilled polymers. Oxides, silica in particular, are the most commonly used inorganic particles because they possess good properties and can be fabricated at a low cost. However, oxides are hydrophilic in nature, and this leads to the presence of water at the interface between the nanoparticles and the polymer matrix. Due to the predominance of particle-matrix interfaces in nanocomposites, the presence of water at the interlayer region can be problematic. Moreover, the hydrophobic nature of most polymers, particularly for polyolefins such as polyethylene, may make it difficult to remove this interfacial water. In this paper, as-received and moistened samples of agglomerated nanosilica/polyethylene were dried using an isothermal treatment at $60^{\circ}C$, and the efficacy of this treatment was studied using dielectric spectroscopy. The Maxwell-Wagner-Sillars relaxation peaks were observed to shift to lower frequencies by three decades, and this was linked to a modification of the water content, due to drying, at the interfaces between silica and polyethylene and at the interfaces within the nanosilica agglomerates. The evolution of the extracted retardation time is explained by the nanosilica hydrophily and the free volume introduced by the nanoparticles.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2000년도 제21회 KOSCO SYMPOSIUM 논문집
• /
• pp.217-228
• /
• 2000

Circulating Fluidized Bed Combustor(CFBC) has been used for the incineration of waste sewage sludge and for the power generation. In this study hydrodynamic characteristics of two phase flow have been studied in a riser section of CFBC. A lab-scale riser is designed and SiC (Geldart type B) is used for solid particles. Experiments are performed by controlling the fluidization parameters including superficial velocity and secondary air to primary air ratio for determination of solid holdup profiles in the riser. Superficial velocities of each fluidization regime are well agreed with results predicted by a theoretical model. The results show that the axial solid holdup distributions calculated by measuring differential static pressures in the riser are found to show a basic profile described by a simple exponential function. Our flow regime during experiments mainly belongs to fast fluidization regime for particle size of 300${\mu}m$. As the SA/PA ratio increases, solid holdup in the lower dense region of the riser increases.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 C
• /
• pp.879-881
• /
• 1999

Radical and ion densities in a CF4 plasma have been calculated as a function of input power density. 9as pressure and feed gas flow rate using simple 0 dimensional global model. Fluorine atom is found to be the most abundant neutral particle. Highly fragmented species such as CF and CF+ become dominant neutral and ionic radical at the high power condition. As the pressure increases. ion density increases but ionization rate decreases due to the decrease in electron temperature. The fractional dissociation of CF4 feed gas decreases with pressure after increasing at the low pressure range. Electron density and temperature are almost independent of flow rate within calculation conditions studied. The fractional dissociation of CF4 monotonically decreases with flow rate. which results in increase in CF3 and decrease in CF density. The calculation results show that the SiO2 etch selectivity improvement correlates to the increase in the relative density of fluorocarbon ion and neutral radicals which has high C/F ratio.

• 한국전기전자재료학회논문지
• /
• 제19권8호
• /
• pp.749-753
• /
• 2006

The $ZnGa_2O_4$ phosphor thick films were fabricated using a screen printing method on Si(100) substrates at various sintering temperatures. The XRD patterns show that the $ZnGa_2O_4$ thick films have a (311) main peak and a spinel structure with increasing sintering temperatures. The particle sizes of $ZnGa_2O_4$ phosphor were about 100 nm and the thickness of $ZnGa_2O_4$ thick film was $10{\mu}m$. The CL and PL properties of $ZnGa_2O_4$ showed main peak of 420nm and maximum intensity at the sintering temperature of $900^{\circ}C$. These results indicate that $ZnGa_2O_4$ phosphor thick films hold promise for displays such as plasma display panel and field emission display.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.55-63
• /
• 2001

Friction and wear properties of brake friction materials containing different metal fibers (Al, Cu or Steel fibers) were investigated using a pad-on-disk type friction tester. Two different materials(gray iron and Al-MMC)) were used for disks rubbing against the friction materials. Results from ambient temperature tests revealed that the friction material containing Cu fibers sliding against cast iron disk showed a distinct negative ${\mu}$-ν (friction coefficient vs. sliding velocity) relation implying possible stick-slip generation at low speed. The negative ${\mu}$-ν relation was not observed when the Cu-containing friction materials were rubbed against the. Al-MMC counter surface. As applied loads increased, friction materials showed higher friction coefficients comparatively. Friction materials slid against cast iron disks exhibited higher friction coefficients than Al-MMC disks during high temperature tests. On the other hand, high temperature test results suggested that copper fibers in the friction material improved fade resistance and the steel fibers were not compatible with Al-MMC disks showing severe material transfer and erratic friction behavior during sliding at elevated temperatures.

• 보존과학회지
• /
• 제22권
• /
• pp.43-60
• /
• 2008

본 연구는 19세기로 알려진 경기도 포천 길명리 가마터에서 선정한 흑유자기와 백자편을 중심으로 과학적 분석을 활용한 특성 자료를 제시해 보고자 한다. 과학적 분석은 미세구조 관찰과 색도와 비중 및 흡수율, 기공률 등을 포함한 물리적 특성, 태토와 유약의 조성에 대한 화학적 특성으로 구분하여 조사하였다. 분석 결과, 태토의 미세구조는 자화 정도에 따라 태토 표면의 입자 및 기공 등에서 차이를 보이며 유약은 백자보다 흑유자기가 유리질화가 잘된 양상으로 관찰된다. 색도와 비중 및 흡수율은 자기의 종류보다 각 도편의 자화 정도에 따른 미세구조에 따라 차이를 보인다. 화학적 조성 분석에서 태토는 백자보다 흑유자기가 $Fe_2O_3$와 $TiO_2$가 높은 편이고 유약은 백자보다 흑유자기가 $SiO_2$, $Al_2O_3$가 낮고 $Fe_2O_3$, $TiO_2$가 높게 함유하고 있는 특징이 있다. 특히, 흑유자기는 CaO와 재의 사용 여부를 말해주는 $P_2O_5$ 성분이 높다.

• Journal of Electrical Engineering and Technology
• /
• 제10권4호
• /
• pp.1621-1625
• /
• 2015

Power quality has always been a concern of power engineers. Certainly an argument can be successfully made that most parts of power engineering have the ultimate objective to improve power quality. AC motors were widely used in industrial and domestic applications. Generally, AC motors were of two types: Induction and Synchronous motors. In motor many parameters like different load cycling, switching, working in hot weather and unbalances creates harmonics which creates major reasons for temperature rise of the motors. Due to high peak value of voltage, harmonics can weaken insulation in cables, windings and capacitors and different electronic components. Higher value of harmonics increase the motor current and decrease the power factor which will reduce the life time of the motor and increase the overall rating of all electrical equipments. Harmonics reduction of all the motors in India will save more power. Coating of windings of the motor with nano fillers will reduce the amount of harmonics in the motor. Based on the previous project works, actions were taken to use the enamel filled with various nano fillers for the coating of the windings of the different AC motors. Ball mill method was used to convert the micro particles of Al₂O₃, SiO₂, TiO₂, ZrO₂ and ZnO into nano particles. SEM, TEM and XRD were used to augment the particle size of the powder. The synthesized nano powders were mixed with the enamel by using ultrasonic vibrator. Then the enamel mixed with the nano fillers was coated to the windings of the several AC motors. Harmonics were measured in terms of various indices like THD, VHD, CHD and DIN by using Harmonic analyzer. There are many other measures and indices to describe power quality, but none is applicable in all cases and in many instances, these indices may hide more than they show. Sometimes power quality indices were used as a basis of comparison and standardization. The efficiency of the motors was increased by 5 – 10 %. The thermal withstanding capacity of the motor was increased by 5º to 15º C. The harmonics of the motors were reduced by 10 – 50%.

• Composites Research
• /
• 제31권5호
• /
• pp.209-214
• /
• 2018

본 연구에서는 친환경적이고 공급이 안정적인 소재를 찾기 위하여, Bio waste인 쌀겨와 조개 껍질에서 활용하여 마이크로 사이즈의 미세 입자를 추출하고, 추출한 입자의 크기와 형상을 분석한 후 CFRP에 첨가하여 물성의 변화를 관찰하였다. 쌀겨와 탄화 쌀겨의 주요구성성분은 탄소, 산소, 규소로 이루어졌으며 탄화과정을 거치면서 탄소와 규소의 비율이 증가함을 확인하였고, 조개 껍질 분말에서는 탄소 산소와 칼슘이 검출되었으며 이는 조개 껍질의 주요구성물질인 탄산칼슘의 영향으로 보인다. 쌀겨 분말의 면적평균은 $6.19{\mu}m$ 체적평균은 $14.77{\mu}m$으로 FE-SEM을 통하여 막대형상의 입자가 관찰되며 이는 쌀겨가 가지고 있던 껍질부분의 주름이나 표면의 털이 남아있는 형상으로 보인다. 탄화쌀겨의 분말은 면적평균은 $1.55{\mu}m$ 체적평균은 $8.20{\mu}m$ 조개 껍질 분말은 면적평균은 $2.53{\mu}m$ 체적평균은 $5.79{\mu}m$로 분석되었으며 쌀겨분말의 경우 막대(Rod)형상의 입자들이 관찰되었고, 조개 껍질 분말의 경우 판상(Plate)의 형상을 가지는 것으로 관찰되었다. CFRP에 첨가하였을 경우 첨가량에 비례하여 물성의 하락이 관찰되었는데 그 폭이 쌀겨분말의 경우가 가장 컸으며, 조개 껍질 분말의 경우 물성하락을 거의 유발하지 않음을 확인하였다.

• 대한기계학회논문집B
• /
• 제35권10호
• /
• pp.997-1003
• /
• 2011

본 연구는 낮은 회 성분의 함량과 높은 발열량의 특성을 지닌 초청정 석탄의 탈휘발 반응율 특성을 연구하였다. 정적 상태에서의 탈휘발 반응율 특성을 얻기 위하여 TGA 장치를 $10^{\circ}C$/min으로 $950^{\circ}C$까지 승온시키며 Coats-Redfern 방법을 사용하여 결과를 도출하였고, 동적 상태에서는 DTF(Drop Tube Furnace) 반응로 온도를 각각 $500^{\circ}C$, $700^{\circ}C$, $900^{\circ}C$, $1100^{\circ}C$, $1300^{\circ}C$로 변화시켜서 실험을 수행하였으며 single step 방법을 통해 탈휘발 반응율 특성을 얻었다. 본 연구를 통해 도출한 초청정 석탄의 탈휘발 반응율 특성은 기존에 사용되어온 Wira(아역청탄)과 Yakurugol(역청탄)의 탈휘발 특성과 비교하였으며, 정적 동적 상태에서 초청정 석탄의 활성화 에너지가 다른 탄종들에 비해 작게 나타났다.