• Korean Journal of Materials Research
• /
• v.20 no.4
• /
• pp.210-216
• /
• 2010

This paper investigates the dependence of a-Si:H/c-Si passivation and heterojunction solar cell performances on various cleaning processes of silicon wafers. It is observed that the passivation quality of a-Si:H thin-films on c-Si wafers depends highly on the initial H-termination properties of the wafer surface. The effective minority carrier lifetime (MCLT) of highly H-terminated wafer is beneficial for obtaining high quality passivation of a-Si:H/c-Si. The wafers passivated by p(n)-doped a-Si:H layers have low MCLT regardless of the initial H-termination quality. On the other hand, the MCLT of wafers incorporating intrinsic (i) a-Si:H as a passivation layer shows sensitive variation with initial cleaning and H-termination schemes. By applying the improved cleaning processes, we can obtain an MCLT of $100{\mu}sec$ after H-termination and above $600{\mu}sec$ after i a-Si:H thin film deposition. By adapting improved cleaning processes and by improving passivation and doped layers, we can fabricate a-Si:H/c-Si heterojunction solar cells with an active area conversion efficiency of 18.42%, which cells have an open circuit voltage of 0.670V, short circuit current of $37.31\;mA/cm^2$ and fill factor of 0.7374. These cells show more than 20% pseudo efficiency measured by Suns-$V_{oc}$ with an elimination of series resistance.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.430-430
• /
• 2012

The surface recombination velocity of the silicon solar cell could be reduced by passivation with insulating layers such as $SiO_2$, SiNx, $Al_2O_3$, a-Si. Especially, the aluminium oxide has advantages over other materials at rear surface, because negative fixed charge via Al vacancy has an additional back surface field effect (BSF). It can increase the lifetime of the hole carrier in p-type silicon. The aluminium oxide thin film layer is usually deposited by atomic layer deposition (ALD) technique, which is expensive and has low deposition rate. In this study, ICP-assisted reactive magnetron sputtering technique was adopted to overcome drawbacks of ALD technique. In addition, it has been known that by annealing aluminium oxide layer in nitrogen atmosphere, the negative fixed charge effect could be further improved. By using ICP-assisted reactive magnetron sputtering technique, oxygen to nitrogen ratio could be precisely controlled. Fabricated aluminium oxy-nitride (AlON) layer on silicon wafers were analyzed by x-ray photoelectron spectroscopy (XPS) to investigate the atomic concentration ratio and chemical states. The electrical properties of Al/($Al_2O_3$ or $SiO_2/Al_2O_3$)/Si (MIS) devices were characterized by the C-V measurement technique using HP 4284A. The detailed characteristics of the AlON passivation layer will be shown and discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.857-860
• /
• 2002

The material that is both conductive in electricity and transparent to the visible-ray is called transparent conducting thin film. It has many field of application such as solar cell, liquid crystal display, transparent electrical heater, selective optical filter, and a optical electric device. In this study, indium tin oxide (ITO ; Sn-doped $In_2O_3$) thin films were deposited on $SiO_2$/soda-lime glass plates by a dc magnetron sputtering technique. The crystallinity and electrical properties of the films were investigated by X-ray diffraction(XRD), atomic force microscopy (AFM) scanning and 4-point probe. The optical transmittance of ITO films in the range of 300-1000nm were measured with a spectrophotometer. As a result, we obtained polycrystalline structured ITO films with (222), (400), and (440) peak. Transmittance of all the films were higher than 90% in the visible range.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.386-386
• /
• 2009

TCO/p/i/n 구조의 비정질 실리콘 박막 태양전지의 제작에 있어서 TCO계면과 p층사이의 이종접합에서의 큰 밴드갭 차이는 p층으로부터의 정공 재결합을 통하여 효율 저하의 원인이 된다. 이러한 재결합은 넓은 밴드갭을 가진 물질을 완충층으로 삽입함으로써 개선되어 질 수 있다. 본 논문에서는 비정질 실리콘 보다 넓은 광학적 밴드갭을 가지는 a-SiOx 박막을 완충층으로 사용하여 TCO/P 계면에서의 재결합 감소에 대한 시뮬레이션을 수행하였다. a-SiOX 박막 내에 포함된 산소의 양에 따라 밴드갭을 조절하여 1.8eV~2.0eV 사이의 완충층을 삽입하여 박막태양전지의 개방전압, 단락전류, 효율 등에 끼치는 영향을 ASA 시뮬레이션을 통하여 알아보았다.

• Korean Journal of Materials Research
• /
• v.29 no.5
• /
• pp.322-327
• /
• 2019

Hole carrier selective MoOx film is obtained by atomic layer deposition(ALD) using molybdenum hexacarbonyl[$Mo(CO)_6$] as precursor and ozone($O_3$) oxidant. The growth rate is about 0.036 nm/cycle at 200 g/Nm of ozone concentration and the thickness of interfacial oxide is about 2 nm. The measured band gap and work function of the MoOx film grown by ALD are 3.25 eV and 8 eV, respectively. X-ray photoelectron spectroscopy(XPS) result shows that the $Mo^{6+}$ state is dominant in the MoOx thin film. In the case of ALD-MoOx grown on Si wafer, the ozone concentration does not affect the passivation performance in the as-deposited state. But, the implied open-circuit voltage increases from $576^{\circ}C$ to $620^{\circ}C$ at 250 g/Nm after post-deposition annealing at $350^{\circ}C$ in a forming gas ambient. Instead of using a p-type amorphous silicon layer, high work function MoOx films as hole selective contact are applied for heterojunction silicon solar cells and the best efficiency yet recorded (21 %) is obtained.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.49-52
• /
• 2009

Practical building integrated photovoltaic system built by Kolon E&C has been monitored and evaluated with respect to power generation, which was installed in Deokpyeong Eco Service Area in Deokpyeong, Gyeonggi, Korea. The amorphous silicon transparent PV module in this BIPV system has 44Wp in power output per unit module and 10% of transmittance with the unit dimension with $980mm{\times}950mm$. The BIPV system was applied as the skylight in the main entrance of the building. This study provided the database for the practical application of the transparent thin-film PV module for BIPV system through 11 month monitoring as well as various statistical analyses such as monthly power output and insolation. Average monthly power output of the system was 52.9kWh/kWp/month which is a 60% of power output of the previously reported data obtained under $30^{\circ}$of an inclined PV module facing south(azimuth=0). This lower power output can be explained by the installation condition of the building facing east, west and south, which was resulted from the influence of azimuth.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.91-91
• /
• 2011

박막태양전지의 높은 효율개선을 위해 TCO층과 p-layer 사이에 buffer layer를 넣어 Voc와 FF를 개선하는 연구가 진행되고 있다. 이에 buffer layer의 활성화 정도를 높이기 위해 p-layer을 최적화 시키고자한다. 이 실험에서 a-Si:B에 N2O를 도핑시켜 Bandgap Energy 2.0 eV, Activation Energy 0.4 eV인 a-SiOx:B 막을 제작하여 buffer layer로 사용하였고 이 buffer layer에 의한 cell의 효율 향상을 최적화 하기위해 ASA simulation을 이용해 p-layer의 Bandgap Energy와 Activation Energy를 가변 하여 보았다. 실험결과 p-layer의 Bandgap Energy 1.95 eV에서 buffer layer와 p-layer사이에서의 barrier가 최소가 됨을 확인 할 수 있었고 Actication Energy 0.5 eV에서 가장 높은 Voc를 가짐을 알 수 있었다. 본 연구를 통해 p-layer의 Bandgap Energy 1.95 eV, Activation Energy 0.5 eV에서 buffer layer를 활성화시키기 위한 p-layer의 최적화 조건을 구현해 볼 수 있었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.366-366
• /
• 2010

Simulation Program (AFORS-HET 2.4.1) was used, include the basic structure of crystalline silicon thin film as above, below Intrinsic a-Si:H films bonded symmetrical structure (Symmetrical structure) were used. Efficiency with variation of the concentration was grown by the a-Si p-type with increasing concentrations of Na, efficiency with increasing a-Si n-type of Nd Concentrations was not changed, was decreased rapidly when concentrations were decreased. Efficiency was increased when c-Si n-type of Nd concentration was increased, otherwise efficiency was decreased when concentration was decreased.

• Electronics and Telecommunications Trends
• /
• v.27 no.1
• /
• pp.38-50
• /
• 2012

박막 태양전지 기술은 현재 가장 큰 시장점유율을 보이고 있는 결정질 Si 태양전지와 비교되는 차세대 태양전지 기술로서 큰 관심을 받고 있다. 결정질 Si 태양전지의 효율보다 높은 효율로서, 훨씬 저가로 생산할 수 있는 수준을 목표로 하여 다양한 종류의 박막 태양전지들이 개발되고 있는데, 본고에서는 그 중에서 가장 많이 연구개발되고 있는 세 종류의 박막 태양전지, 즉, 화합물 반도체 박막 태양전지 중 가장 대표적인 CIGS(Cu(InGa)Se2) 태양전지, 지구상에 가장 풍부한 무기 소재인 Si를 기반으로 하는 비정질 Si 박막 태양전지, 그리고 유기물 기반 태양전지 중 가장 높은 효율을 나타내는 DSSC에 대해서 중점적으로 기술하였다.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.4
• /
• pp.111-115
• /
• 2015

To improve the efficiency of the Si solar cell, high minority carrier life time is required. Therefore, the passivation technology is important to eliminate point defects on the silicon surface, causing the loss of minority carrier recombination. PECVD or post-annealing of thermally-grown $SiO_2$ is commonly used to form the passivation layer, but a high-temperature process and low thermal stability is a critical factor of low minority carrier lifetime. In this study, atomic layer deposition was used to grow the $Al_2O_3$ passivation layer at low temperature process. $Al_2O_3$ was selected as a passivation layer which has a low surface recombination velocity because of the fixed charge density. For the high charge density, an improved minority carrier lifetime, and a low surface recombination, nitrogen was doped in the $Al_2O_3$ thin film and the improvement of passivation was studied.