• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.318-321
• /
• 2002

This paper presents a proper condition to achieve high conversion efficiency using PC1D simulator on sri-crystalline Si solar cells. Various efficiency influencing parameters such as rear surface recombination velocity and minority carrier diffusion length in the base region, front surface recombination velocity, junction depth and doping concentration in the Emitter layer, BSF thickness and doping concentration were investigated. Optimized cell parameters were given as rear surface recombination of 1000 cm/s, minority carrier diffusion length in the base region 200 $\mu\textrm{m}$, front surface recombination velocity 100 cm/s, sheet resistivity of emitter layer 100 Ω/$\square$, BSF thickness 5 $\mu\textrm{m}$, doping concentration 5${\times}$10$\^$19/ cm$\^$-3/. Among the investigated variables, we learn that a diffusion length of base layer acts as a key factor to achieve conversion efficiency higher than 19 %.

• New & Renewable Energy
• /
• v.18 no.1
• /
• pp.29-34
• /
• 2022

The most prevalent cause of solar cell efficiency loss is reduced recombination at the metal electrode and silicon junction. To boost efficiency, a a SiO_X/poly-Si passivating interface is being developed. Poly-Si for passivating contact is formed by various deposition methods (sputtering, PECVD, LPCVD, HWCVD) where the ploy-Si characterization depends on the deposition method. The sputtering process forms a dense Si film at a low deposition rate of 2.6 nm/min and develops a low passivation characteristic of 690 mV. The PECVD process offers a deposition rate of 28 nm/min with satisfactory passivation characteristics. The LPCVD process is the slowest with a deposition rate of 1.4 nm/min, and can prevent blistering if deposited at high temperatures. The HWCVD process has the fastest deposition rate at 150 nm/min with excellent passivation characteristics. However, the uniformity of the deposited film decreases as the area increases. Also, the best passivation characteristics are obtained at high doping. Thus, it is necessary to optimize the doping process depending on the deposition method.

• Current Photovoltaic Research
• /
• v.1 no.1
• /
• pp.69-72
• /
• 2013

Combined nano- and micro-wires (CNMWs) Si arrays were prepared using PR patterning and silver-assisted electroless etching. A $POCl_3$ doping process was applied to the fabrication of CNMWs solar cells. KOH solution was used to remove bundles in CNMWs and the etching time was varied from 30 to 240 s. The lowest reflectance of 3.83% was obtained at KOH etching time of 30 s, but the highest carrier lifetime of $354{\mu}s$ was observed after the doping process at 60 s. At the same etching time, a $V_{oc}$ of 574 mV, $J_{sc}$ of $28.41mA/cm^2$, FF of 74.4%, and Eff. of 12.2% were achieved in the CNMWs solar cell. CNMWs solar cells have potential for higher efficiency by improving the post-process and surface-rear side structure.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1738-1740
• /
• 1999

This paper deals with a novel structure of poly-Si solar cell. A solar cell conversion efficiency was degraded by grain boundary effect in Polycrystalline silicon. To reduce grain boundary effect, we performed a preferential grain boundary etching, $POCl_3$ n-type emitter doping, and then ITO film growth on poly-Si. Among the various preferential etchants, Schimmel etch solution exhibited the best result having grain boundary etch depth about $10{\mu}m$. RF magnetron sputter grown ITO films showed a low resistivity of $10^{-4}\Omega-cm$ and high transmittance of 85%. With well fabricated poly-Si solar cells. we were able to achieve as high as 15% conversion efficiency at the input power of 20mW/$cm^2$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.129.2-129.2
• /
• 2011

본 연구에서는 a-Si:H/c-si 구조의 이종접합 태양전지의 p a-Si:H 에미터 층의 박막 조건에 따라 태양전지 특성을 연구하였다. p, n-layer는 PECVD (Plasma-enhanced chemical vapor deposition) i-layer는 HWCVD(Hot wire chemical vapor deposition), ITO는 RF 마그네트론 스퍼터링법으로 제작하였다. p-layer의 도핑 농도, 기판 증착 온도, 증착 높낮이에 따라 특성을 비교 분석 하였다. QSSPC로 minority carrier life time, 자외 가시선 분광분석 장치로 투과 반사도를, Ellipsometer로 흡수 계수, 두께, FTIR로 막의 구성요소 등의 변화를 조사하여 개선된 p a-Si:H의 특성이 이종접합 태양전지에서 효율향상에 영향을 주는지 Photo IV와 EQE를 통하여 조사하였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.702-705
• /
• 2011

Poly-Si wafers with resistivity of 1 [${\Omega}$-cm[ and thickness of 50 [${\mu}m$] were used as a starting material. Various efficiency influencing parameters such as rear surface recombination velocity and minority carrier diffusion length in the base region, front surface recombination velocity, junction depth and doping concentration in the Emitter layer, BSF thickness and doping concentration were investigated. Optimized cell parameters were given as rear surface recombination of 1000 [cm/sec], minority carrier diffusion length in the base region 50 [${\mu}m$], front surface recombination velocity 100 [cm/sec], sheet resistivity of emitter layer 100 [${\Omega}/{\Box}$], BSF thickness 0.5 [${\mu}m$], doping concentration $5{\times}10^{19}\;cm^{-3}$. Among the investigated variables, we learn that a diffusion length of base layer acts as a key factor to achieve conversion efficiency higher than 19.8 %. Further details of simulation parameters and their effects to cell characteristics are discussed in this paper.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.74.2-74.2
• /
• 2010

유리를 기판으로 하는 실리콘 박막태양전지의 경우 PIN 비정질 태양전지 뒤에 후면반사막으로 주로 Ga 또는 Al이 Doping된 후면반사막을 사용한다. 이 후면반사막의 경우 PIN층을 통과한 빛을 반사함으로써 빛의 효용성을 높이는 데 그 목적이 있다. 본 논문에서는 후면박사막으로 ZnO:Al을 사용하고 산소 부여량에 따른 투과도, 비저항 변화를 살펴보고 실제로 a-Si:H 박막태양전지를 제작하여 그 효과를 파악하였다. 이 때 산소 부여량이 많아질 경우 투과도는 높아지지만 비저항이 급격히 높아지는 문제가 있었으나 이 조건으로 a-Si:H 박막태양전지를 제작시에도 효율이 상승하였다.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.1
• /
• pp.65-69
• /
• 2017

This paper presents a Technology-CAD (TCAD) simulation of the characteristics of crystalline Si pillar array solar cells. The junction depth and the surface concentration of the solar cells were optimized to obtain the targeted sheet resistance of the emitter region. The diffusion model was determined by calibrating the emitter doping profile of the microscale silicon pillars. The dimension parameters determining the pillar shape, such as width, height, and spacing were varied within a simulation window from ${\sim}2{\mu}m$ to $5{\mu}m$. The simulation showed that increasing pillar width (or diameter) and spacing resulted in the decrease of current density due to surface area loss, light trapping loss, and high reflectance. Although increasing pillar height might improve the chances of light trapping, the recombination loss due to the increase in the carrier's transfer length canceled out the positive effect to the photo-generation component of the current. The silicon pillars were experimentally formed by photoresist patterning and electroless etching. The laboratory results of a fabricated Si pillar solar cell showed the efficiency and the fill factor to be close to the simulation results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.453-456
• /
• 1999

The Si-SiO$_2$interface trap and nitride bulk trap distribution of SONOSFET(polysilicon-oxide-nitride-oxide-semiconductor)NVSM(nonvolatile semiconductor memory) cell were investigated by single charge pumping method. The used device was fabricated by 0.35 7m standard logic fabrication including the ONO cell process. This ONO dielectric thickness is tunnel oxide 24 $\AA$, nitride 74 $\AA$, blocking oxide 25 $\AA$, respectively. Keeping the pulse base level in accumulation and pulsing the surface into inversion with increasing amplitudes, the charge pumping current flow from the single junction. Using the obtained I$_{cp}$-V$_{h}$ curve, the local V$_{t}$ distribution, doping concentration, lateral interface trap distribution and lateral memory trap distribution were extracted. The maximum N$_{it}$($\chi$) of 1.62$\times$10$^{19}$ /cm$^2$were determined.mined.d.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.193-193
• /
• 2013

실리콘 박막 태양전지는 광 흡수층에서 형성된 정공과 전자를 효과적으로 분리하기 위해 p형과 n형으로 도핑된 층을 형성하는 p-i-n구조를 갖게 된다. 이러한 도핑 층을 형성하기 위해 B2H6와 PH3와 같은 독성 가스를 사용하기 때문에, 공정 안정성과 환경적인 이슈가 대두된다. 또한 도핑은 추가적으로 실리콘 박막 태양전지의 안정화 효율을 지속적으로 저하시키는 요인이 된다. 이러한 문제점을 개선하기 위하여, 창층으로 MoO3, V2O5, WO3 등과 같이 높은 일함수를 갖는 전이금속 산화물을 사용하고, 광 흡수층으로 i-Si:H을, 후면 전극으로 낮은 일함수를 나타내는 LiF/Al을 사용하였다. 전이금속 산화물과 LiF/Al의 큰 일함수 차이에 의해서 흡수층인 i-Si:H 에서 생성된 캐리어들은 효과적으로 분리되고 수집이 된다. 금속 산화물은 스퍼터링 공정에 의하여 이루어졌으며, 스퍼터링 공정조건에 따라 산화도가 조절되며, 이러한 산화도에 따라 태양전지의 셀 특성이 결정된다. 도핑 층이 없는 새로운 형태의 실리콘 박막 태양전지는 기존 비정질 실리콘 박막 태양전지에 비해 높은 안정화 효율을 나타내며, 이는 도핑 층이 없기 때문에 기존 실리콘 박막 태양전지의 열화현상에 따른 효율저하가 발생하지 않는 장점을 지내고 있다.