• Journal of the Korean institute of surface engineering
• /
• v.49 no.3
• /
• pp.245-251
• /
• 2016

Galvanizing method has been extensively used to the numerous constructional steels such as a guard rail of high way, various types of structural steel for ship building and various types of steels for the industrial fields etc.. However, the galvanized structures would be inevitably corroded rapidly with increasing exposed time because an acid rain due to environmental contamination has been much dropped more and more. Therefore, it has been made an effort to improve the corrosion resistance of the galvanizing film through various methods. In this study, comparison evaluation on the corrosion resistance of three types of the samples, that is, the hot dip galvanizing with pure zinc(GI), the hot dip galvanizing of alloy bath with zinc and aluminum(GL) and the pure zinc galvanizing steel immersed again to chromate treatment bath(Chro.)were investigated using electrochemical methods in 1% $H_2SO_4$ solution. The Chro. and GI samples exhibited the highest and lowest corrosion resistance respectively in 1% $H_2SO_4$ solution, however, the GI sample revealed the highest impedance at 0.01 Hz due to its high resistance polarization caused by corrosion products deposited on the surface, while Chro. sample exhibited the lowest impedance at 0.01 Hz because of little corrosion products on the surface. Consequently, it is suggested that the chromate treated steel has a better corrosion resistance in acid environment compared to pure galvanizing(GI) or galvalume(GL) steels.

• Journal of Navigation and Port Research
• /
• v.33 no.1
• /
• pp.35-41
• /
• 2009

A waypoint tracking algorithm(WTA) is designed for Unmanned Surface Vehicle(USV) in which water-jet system is installed for propulsion To control the heading of USV for waypoint tracking, the steering nozzle of water-jet need, to be controlled. Firstly, target heading is calculated by using the position information of waypoints input from the land control center. Secondly, the command for the steering nozzle of water-jet is calculated in real time by using the heading and the rate-of-turn( ROT) from magnetic compass, In this study, in order to consider the drift angle due to external disturbance such as wind and wave, the course of ground( COG) can be used instead of heading at higher speed than a certain value, To test the performance of newly-designed WTA, the tests were carried out in actual sea area near Gwang-an bridge of Busan. In this paper, the sea trial test results from WTA are analyzed and compared with those from manual control and those from commercial controller.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.10
• /
• pp.940-948
• /
• 2012

In Korea, researches on the exposure assessment of the hand-transmitted vibration started from the mid-90, however, they were performed in the limited industries such as auto-assembly plants and the evaluation of the vibration was mostly conducted by ISO 5349(1986). Therefore, it was necessary to assess hand-transmitted vibration levels of workplace such as ship building/repairing industry or mining industry where occupational injuries are largely occurred and to evaluate the vibration levels using revised ISO 5349(2001). The SVAN 948 Four Channels Sound & Vibration Analyser was used for the measurement. The workers using a chain saw were exposed to 1.7~2.8 $m/s^2$ of daily vibration level. Workers using a rock drill in a coal mining were exposed to the highest vibration acceleration among workers and the levels were 7.1~10.8 $m/s^2$. Vibration levels of grinders were different according to the types of grinders. The hand-transmitted vibration of 3 types of grinders were measured and the levels were 3.3~11.1 $m/s^2$. Workers using a impact wrench were exposed to 1.5~1.6 $m/s^2$ of vibration. Out of 20 kinds of machines, only 4 tools provided the information of vibration acceleration on the instructions. In addition, the current condition of workplace to control vibration was not much different from the past because there are no vibration exposure limit.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.2
• /
• pp.115-126
• /
• 2016

In the process of ship building, it is known that the maintenance of working period and saving cost are one of the important part during the logistics of blocks transportation. Precise operational planning inside the shipyard plays a big role for a smooth transportation of blocks. But many problems arise in the process of block transportation such as the inevitable road damage during the transportation of the blocks, unpredictable stockyard utilization of the road associated with a particular lot number, addition of unplanned blocks. Therefore, operational plan needs to be re-established frequently in real time for an efficient block management. In order to find the shortest path between lot numbers, there are several representative methods such as Floyd algorithm that has the characteristics of many-to-many mapping, Dijkstra algorithm that has the characteristic of one-to-many mapping, and the A* algorithm which has the one-to-one mapping, but many authors have published without the mutual comparisons of these algorithms. In this study, some appropriate comparison have been reviewed about the advantages and disadvantages of these algorithms in terms of precision and cost analysis of calculating the paths and planning system to operate the transporters. The flexible operating plan is proposed to handle a situation such as damaged path, changing process during block transportation. In addition, an operational algorithm of a vacant transporter is proposed to cover the shortest path in a minimum time considering the situation of transporter rotation for practical use.

• Elastomers and Composites
• /
• v.15 no.3
• /
• pp.147-154
• /
• 1980

The cellular rubber products for industrial purpose have been applied in many fields such as auto-motive parts, ship-building, machinery, sports goods, diving suit or interior housings etc. The purpose of this dissertation is to study the physical properties of celluar rubber products particulary for those elastomers such as EPDM, CR and NBR with heat resistance property, weather proofness, and oil resistance characteristics respectively, aiming at improving their quality, and renovating the manufacturing know-how which is beyond our technical power at the present time in Korea. In order to meet this requirement an ideal recipe is being shown for the three elastomers, and also a practical recipe which is easily available in terms of compounding ingredients in domestic market has set up as shown in Table 1. for the investigation of vulcanization characteristics by means of Rheometer. The optimum Mooney viscosity of compounded rubber was found to be approximately $ML_{1+4}(100^{\circ}C)$ $30\sim45$. Excess mustication makes a dispersion of ingredients worse, consequently it causes deformation of shapes and heterogenous cell distribution. In other words the articles are rejected because of its insufficient workmanship. The results of physical properties of the products are indicated in Table 3. It has shown that the quality meet requirement when tested in accordance with ASTM D572, 573 and D 395. The test results o CR/IR blends in terms of hardness, volume change by blowing, tensile strength and elongation have been shown.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.7
• /
• pp.907-915
• /
• 2018

With the increase of metal usage in various industries, metal pollution and ecological toxicity in the environmental system have become a significant concern. A geo-statistical index has been widely used to determine contamination level with normalization through a background value. In this study, geo-statistical indexes such as an enrichment factor, accumulation index, and potential ecological risk index were used to assess metal pollution in soil at locations associated with shipbuilding manufacturing industries. Metal contamination, especially of Cu and Pb, was observed in some samples located closer to manufacturing sites. Enrichment factor and accumulation (IGEO) values were indicative of concerning levels of soil contamination in specific samples, and the soil contamination could be induced by anthropogenic sources. In further study, after more detailed sampling for soil and potential pollution sources, high interpretation techniques such as Pb isotope analysis and X-ray analysis will be needed to investigate source identification.

• Corrosion Science and Technology
• /
• v.18 no.4
• /
• pp.129-137
• /
• 2019

CFRP (Carbon Fiber Reinforced Plastics) is composed of carbon fiber and plastic resin, and is approximately 20 - 50% lighter than metallic materials. CFRP has a low density, higher specific stiffness, specific strength, and high corrosion resistance. Because of these excellent properties, which meet various regulation conditions needed in the industrial fields, CFRP has been widely used in many industries including aviation and ship building. However, CFRP reveals water absorption in water immersion or high humidity environments, and water absorption occurs in an epoxy not carbon fiber, and can be facilitated by higher temperature. Since these properties can induce volume expansion inside CFRP and change the internal stress state and degrade the chemical bond between the fiber and the matrix, the mechanical properties including bond strength may be lowered. This study focused on the effects of NaCl concentration (0.01 - 1% NaCl) and solution temperature ($30-75^{\circ}C$) on the galvanic corrosion between CFRP and A516Gr.55 carbon steel. When NaCl concentration increases 10 times, corrosion rate of a specimen was not affected, but that of galvanic coupled carbon steel increased by 46.9% average. However, when solution temperature increases $10^{\circ}C$, average corrosion rate increased approximately 22%, regardless of single or galvanic coupled specimen.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.1
• /
• pp.80-87
• /
• 2021

Most container ships are currently being constructed as Ultra-Large Container Ships. Hence, the equipment of the ships is also becoming relatively large. In particular, propellers, rudders, and rudder stocks are large in the stern structure, and in relation, efficient design of the hull structures to safely secure these parts is important. The bottom shell plate surface of a stern skeg is a perforated plate from which the rudder stock penetrates, so it is an important component for the stern structure. In this paper, to determine the critical buckling of the shell plate, an interaction curve equation for the two-axis compression of the shell plate was derived using the maximum value of the static structural stress multiplier in a load multiplier mode. This equation predicts the timing of the buckling occurrence. By analyzing this interaction curve equation, the buckling behavior of the plates subjected to a combination load was determined and the usefulness of applying it to ship building was investigated.

• Journal of the Institute of Convergence Signal Processing
• /
• v.23 no.1
• /
• pp.37-43
• /
• 2022

Drones, one of the 4th industrial technologies that are expanding from military use to industrial use, are being actively used in the search missions of the National Police Agency and finding missing persons, thereby reducing interest in a wide area and the input of large-scale search personnel. However, legal review of police drone operation is continuously required, and the importance of advanced system for related operations and analysis of captured images in connection with search techniques is increasing at the same time. In this study, in order to facilitate recording, preservation, and monitoring in the concept of precise search and monitoring, it is possible to achieve high efficiency and secure golden time when precise search is performed by constructing spatial information based on photo rather than image data-based search. Therefore, we intend to propose a spatial information construction technique that reduces the resulting data volume by adjusting the unnecessary spatial information completion rate according to the size of the subject. Through this, the scope of use of drone search missions for large-scale areas is advanced and it is intended to be used as basic data for building a drone operation manual for police searches.

• Korean Journal of Remote Sensing
• /
• v.38 no.5_2
• /
• pp.661-667
• /
• 2022

As remote sensing and GIS have been considered to be essential technologies for disasters information production, researches on developing methods for analyzing spatial data, and developing new technologies for such purposes, have been actively conducted. Especially, it is assumed that the use of remote sensing and GIS for disaster management will continue to develop thanks to the launch of recent satellite constellations, the use of various remote sensing platforms, the improvement of acquired data processing and storage capacity, and the advancement of artificial intelligence technology. This spatial issue presents 10 research papers regarding ship detection, building information extraction, ocean environment monitoring, flood monitoring, forest fire detection, and decision making using remote sensing and GIS technologies, which can be applied at the disaster prediction, monitoring and response stages. It is anticipated that the papers published in this special issue could be a valuable reference for developing technologies for disaster management and academic advancement of related fields.