• 한국산학기술학회논문지
• /
• 제6권2호
• /
• pp.122-128
• /
• 2005

본 연구에서는 구조용강 SM520을 사용하여 교량용 박스 제작시 플럭스 코어드 아크용접법에서 가스실드방식과 셀프실드방식의 두 공정으로 제작된 용접부를 건전성, 기계적 성질 및 미세조직에서 비교하였다. 그 결과 두 용접 프로세스에 의해 제작된 용접부들은 매크로 조직 및 비파괴 검사 결과 건전성이 입증되었고, 항복 및 인장강도가 각각 $462{\sim}549\;MPa$와 $548{\sim}640\;MPa$였고, CVN 충격치는 $-20^{\circ}C$에서 요구값인 40J을 충족하였다. 결과적으로, 고속철도나 고속도로 건설시 사용되는 교량용 SM520강 박스 제조시 고소 및 강풍 조건하에서 용접할 때 셀프실드 아크용접법은 기존의 가스실드 아크 용접법과 비교하여 대등한 용접 특성들을 보였기 때문에 현장 시공시 적용 타당성이 있다고 사료된다.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1999년도 춘계학술발표회요약집
• /
• pp.350-350
• /
• 1999

• 한국전기전자재료학회논문지
• /
• 제18권10호
• /
• pp.960-964
• /
• 2005

In this paper, we dealt with a partial discharge(PD) measurement method that has been accepted as an effective and non-destructive technique to estimate insulation performance of low-voltage electric and electronic devices. The PD measurement system Is composed of a coupling network, a low noise amplifier, and associated electronics. h shielded box Is adopted to make a better measurement environment against around noise. A low cut-off frequency of the coupling network estimated by a sinusoidal wave input was 125 kHz (-3 dB). Calibration tests on laboratory set-up have shown that the PD measurement system has a stable sensitivity of 10 mV/pC. In an application test oil a low-voltage three phase Induction motor (5 HP), we could detect 0.53 pC level of partial discharge at the applied voltage of AC 650 $V_{peak}$.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2005년도 춘계학술발표회
• /
• pp.273-274
• /
• 2005

• Progress in Superconductivity
• /
• 제12권2호
• /
• pp.124-128
• /
• 2011

We have developed a high-$T_C$ SQUID magnetometer system to measure magnetocardiograms of laboratory rats. White noise of the measurement system was about 50 fT/$Hz^{1/2}$ when measured in a magnetically shielded box. We optimized the measurement position to obtain clear MCG wave from rat's small heart by using grid measurements. With the optimization, the MCG signal was successfully detected with the peak amplitude of about 50 pT. We could observe well defined P-, QRS-, and T-wave from the rat MCG. The results suggest that the developed system has a strong potential to monitor the progress of heart disease model using laboratory rat.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.1887-1891
• /
• 2008

In this paper, we dealt with a partial discharge (PD) measurement method that has been accepted as an effective and non-destructive technique to estimate insulation performance of low-voltage induction motors. The PD measurement system consists of a coupling network, a low noise amplifier, and associated electronics. A shielded box was used to reduce environmental noise. Frequency characteristic of the coupling network was estimated by a sinusoidal signal input, and the low cut-off frequency of the coupling network was 1 MHz (-3 dB). Also, we carried out a calibration test for the PD measurement system. Sensitivity of the system was of 84 m$V_{max}$/pC between stator winding and enclosure. In application test on a low-voltage three phase induction motor (5 HP), we could detect 88 pC at AC 800 $V_{max}$.

• 한국산업보건학회지
• /
• 제33권4호
• /
• pp.439-446
• /
• 2023

Objectives: The aims of this study are to investigate how X-rays are emitted to surrounding parts during the ion implantation process, to analyze these emissions in relation to the properties of the ion implanter equipment, and to estimate the resulting exposure dose. Eight ion implanters equipped with high-voltage electrical systems were selected for this study. Methods: We monitored X-ray emissions at three locations outside of the ion implanters: the accelerator equipped with a high-voltage energy generator, the impurity ion source, and the beam line. We used a Personal Portable Dose Rate and Survey Meter to monitor real-time X-ray levels. The SX-2R probe, an X-ray Features probe designed for use with the Radiagem^TM meter, was also utilized to monitor lower ranges of X-ray emissions. The counts per second (CPS) measured by the meter were estimated and then converted to a radiation dose (𝜇Sv/hr) based on a validated calibration graph between CPS and μGy/hr. Results: X-rays from seven ion implanters were consistently detected in high-voltage accelerator gaps, regardless of their proximity. X-rays specifically emanated from three ion implanters situated in the ion box gap and were also found in the beam lines of two ion implanters. The intensity of these X-rays did not show a clear pattern relative to the devices' age and electric properties, and notably, it decreased as the distance from the device increased. Conclusions: In conclusion, every gap, in which three components of the ion implanter devices were divided, was found to be insufficiently shielded against X-ray emissions, even though the exposure levels were not estimated to be higher than the threshold.

• 분석과학
• /
• 제13권5호
• /
• pp.601-607
• /
• 2000

란탄은 사용후핵연료의 연소도 지표원소들 중 하나로써 이용되고 있다. $U_3Si/Al$ 사용후핵연료는 다량의 U과 Al 속에 미량의 La이 포함되어 있어 정량시 매질의 영향을 줄이기 위해 화학적 분리가 요구된다. La의 분리 및 측정을 위해 IC-ICP-MS를 이용하였으며, 우선 방사성 시료를 취급하기 위하여 유도결합 플라스마 질량분석기의 플라스마 부분 및 분리관을 방사선 차폐 글로브박스 내에 설치하였다. CG10 분리관과 ${\alpha}$-HiBA 용리액을 사용하여 U, Al, La 및 몇 가지 핵분열생성물 (Sr, Zr, Y, Mo, Ru, Pd, Rh, Cs, Ba, Ce, Pr, Nd, Sm, Eu 및 Cd)의 머무름 거동을 살펴보았다. 0.2 M ${\alpha}$-HiBA 용리액에서 U과 Al이 초기에 용출되므로 분리관과 ICP-MS의 시료분무기 사이에 3방향 밸브를 연결하여 다량의 U과 Al이 ICP-MS로 유입되지 않도록 하므로써 매질의 영향을 줄일 수 있었다. 이 조건에서 La은 약 12분 정도에 분리 및 측정이 가능하였으며, $1-10{\mu}g/L$ (ppb)의 농도범위가 측청에 적합하였고 시료양을 $200{\mu}L$ 취할 경우 La의 검출한계는 $0.25{\mu}g/L$이었다.