• 한국기계가공학회지
• /
• 제18권5호
• /
• pp.74-81
• /
• 2019

This study reports the CW $CO_2$ laser scribing of soda lime glass. In this study, scribing experiments are carried out at different laser powers, scan speeds, and focal positions to investigate the effect of the process parameters on the interaction characteristics between a laser beam and glass. In particular, the interaction characteristics are analyzed and described with the input laser energy per unit length. According to the experimental results, the damage threshold for the glass surface was found to exist between 0.072 and 0.08 J/mm. The input laser energy in this region induced partial melting of the surface and grain-shaped cracks. These cracks tended to increase as the input laser energy increased. At the laser input energy larger than 1 J/mm, a huge crack propagating along the scan direction was produced, and the volume below the scribed area was fully melted. The growth of this crack finally resulted in the complete cutting of the glass at the input laser energy above 8 J/mm. It was found that both the width and depth of the scribed line increased with increasing input laser energy. For the beam focusing at the rear surface, the width of the scribed line varied irregularly. This could be ascribed to the increased asymmetry of the beam intensity distribution when the laser beam was focused at the rear surface. Under this condition, a large burr was only produced on one side of the scribed line.

• 한국전자파학회논문지
• /
• 제20권2호
• /
• pp.141-146
• /
• 2009

본 논문에서는 인위적인 커패시턴스 값의 변화에 따라서 공진 주파수가 이동하여 다중 대역을 포함하는 이중 대역 공진 주파수 변환 안테나를 제안하였다. 인위적인 커패시턴스 값의 변화는 버랙터 다이오드 조절의 선행연구로써, 칩 커패시터를 이용해 주파수 변환 범위와 안테나 특성에 관해 분석하였다. T자 모양 슬릿의 짧은 부분에 장착된 서로 다른 칩 커패시터는 안테나의 입력 임피던스의 변화를 준다. 변화된 입력 임피던스는 안테나의 방사 패턴의 변화 없이, 일정한 범위 내에서 이중 대역 공진주파수를 유지하면서 가변함을 실험을 통해 검증하였다. 제안한 안테나의 공진 주파수는 저주파 대역과 고주파 대역에서 각각 400 MHz, 200 MHz의 범위안에서 변화가 가능하다. 또한, 10 dB 반사 손실 대역폭은 저주파 대역에서 $0.78{\sim}1.21\;GHz$, 대역폭 10 MHz를 가지며, 고주파 대역에서는 $1.97{\sim}2.17\;GHz$, 대역폭 50 MHz를 가진다. 제안한 안테나는 저주파 대역에서 0 dBi, 고주파 대역에서 3 dBi의 안테나 이득을 갖는다.

• 한국정밀공학회지
• /
• 제18권8호
• /
• pp.157-163
• /
• 2001

This paper presents the new linear notion device so called \"inch-werm\" which gets large displacement by incrementally summing small displacements of PZT actuators. Dynamic stiffness of inch-worm is generally low compared to its driving condition due to the requirement of inch-worm like small size and light weight. This low stiffness may degenerate the positional precision of inch-worm. An inch-worm is realized using three PZT actuators, a monolithic moving device and a guide way frame. Finite element method and experimental approach are used to analyse the static and dynamic motion of the designed inch-worm. Command reference input is shaped to reduce the residual vibration of inch-worm. The practical feasibility of inch-worm is also examined by running tests.ing tests.

• 한국통신학회논문지
• /
• 제21권12호
• /
• pp.3256-3264
• /
• 1996

This paper presents an efficient VLSI architecture for transposing matris in high speed. In the case of transposing N*N matrix, N$^{2}$ numbers of transposition cells are configured as regular and spuare shaped structure, and pipeline structure for operating each transposition cell in paralle. Transposition cell consists of register and input data selector. The characteristic of this architecture is that the data to be transposed are divided into several bundles of bits, then processed serially. Using the serial transposition of divided input data, hardware complexity of transpositioncell can be reduced, and routing between adjacent transposition cells can be simple. the proposed architecture is designed and implemented with 0.5 .mu.m VLSI library. As a result, it shows stable operation in 200 MHz and less hardware complexity than conventional architectures.

• 전기학회논문지
• /
• 제58권8호
• /
• pp.1580-1584
• /
• 2009

We have theoretically analyzed the monolithic integration of vertical cavity lasers with depleted optical thyristor (VCL-DOT) structure and experimentally demonstrated optical logic gates such as AND-gate, OR-gate, and INVERTER implemented by VCL-DOT for an optical programmable gate array. The optical AND and OR gates have been realized by changing a input bias of the single VCL-DOTs and all kinds of optical logic functions are also implemented by adjusting an intensity of the reference input beams into the differential VCL-DOTs. To achieve the high sensitivity, high slope efficiency and low threshold current, a small active region of lasing part and a wide detecting area are simultaneously designed by using a selective oxidation process. The fabricated devices clearly show nonlinear s-shaped current-voltage characteristics and lasing characteristics of a low threshold current with 0.65 mA and output spectrum at 854 nm.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -2
• /
• pp.1030-1033
• /
• 2002

This paper, a new simple controller operates in continuous conduction mode (CCM) for Boost power factor collection converter is introduced. The duty ratios are obtained by comparisons of a sensed signal from inductor current and a negative ramp carrier waveform in each switching period. By using the proposed controller, input voltage sensing, error amplifier in the current feedback loop, and analog multiplier／divider are not required, then, the control circuit implementation is very simple. To verify the proposed controller, the circuit simulation for Boost power factor correction converter was applied. For the results, the input current waveform was shaped to be closely sinusoidal, implying low THD.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.272-277
• /
• 2003

This paper reports the fluid flow and heat transfer around a module cooled by forced air flow generated by a piezoelectric(PZT) cooling fan. A flexible PZT fan with distortion in a fluid transport system of comparatively simple structure which was mounted on a PCB in a parallel-plate channel($450{\times}80{\times}700mm^3$) accelerates surrounding fluid locally. Input voltages of 20-100V and a resonance frequency of 23Hz were used to vibrate the cooling fan. Input power to the module was 4W. The cooling effect using a PZT fan was larger than that of free convection. Fluid flow around the module were visualized by using PIV system. The temperature distribution around heated module were visualized by using liquid crystal film(LCF). We found that the flow type was y-shaped and the cooling effect was increased by the wake generated by a piezoelectric cooling fan.

• 한국암반공학회:학술대회논문집
• /
• 한국암반공학회 2004년도 추계학술발표 논문집
• /
• pp.171-180
• /
• 2004

Underground mining causes surface subsidence long after the mining operation had been ceased. Surface subsidence can be in the form of saucer-shaped depression or collapsed chimneys or sinkholes. Sinkhole formations are predominant over shallow-depth room and pillar mines having weak overburden strata. In this study, occurrences of sinkholes due to mining activity are assessed based on local geological conditions and mining parameters using fuzzy reasoning techniques. All input and output parameters are represented with linguistic hedges. Numerous fuzzy rules are developed to relate sinkhole occurrences with input parameters using fuzzy relational matrix. Based on the combined fuzzy rules, possibility of sinkhole occurrences can be ascertained once the geological and mining parameters of any area are known.

• 동력기계공학회지
• /
• 제11권1호
• /
• pp.134-139
• /
• 2007

A delivery ship is used to handle the cargo with the crane to/from the ships. The ship is inclined in the direction of a cargo which is hung on a crane. In this case, a arc shaped rail should be in the equilibrium state to get good anti-rolling performance. In this study, a device and control algorithm are developed to take accurate and quick equilibrium of the rail. The device is composed of a hinged immovable support, screw jack and damper. And the control system is based on I-PD control law to consider of control input saturation and overshoot. The controller is composed of integral controller of feedforward path and proportional-derivative controller of feedback path. The parameters of controller is designed to follow the reference signal and to remove overshoot. The simulation results show that the desirable control performance is achieved.

• 한국소음진동공학회논문집
• /
• 제24권7호
• /
• pp.537-548
• /
• 2014

In this paper, horn loudspeaker modeling was suggested, investigated and verified through comparison of test results and simulation ones based on input electrical impedance curves and acoustic sensitivity ones. First, Thiele Small parameters of horn driver were identified by using pseudo loudspeaker model concept and verified in case of both closed and open horndriver. Second, cone-shaped horn models were investigated and compared with input acoustic impedance curves for real horn(cone angle $6.6^{\circ}$) and short horn(cone angle $27.9^{\circ}$). It showed that Leach model for cone horn was well described to test results, which were electrical impedance and acoustic sensitivity, compared to Lemaitre one. To represent horn system model good approximation in wide frequency range, mass correction filter and lowpass filter were adopted and consequently showed good fitted to test results.