• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.11a
• /
• pp.173-174
• /
• 2014

In this research, the effect of the amount of retarder and the washing timing on the quality of aggregate-exposed concrete produced by water-jet washing method is evaluated as a series of test to develop the aggregate-exposed concrete as a concrete finishing method. As a result, the amount of losing aggregate and surface mortar was increased as the dosage of retarder was increased because of the hydration retarding effect of the retarder. Furthermore, as the washing timing was extended, the mortar on the surface of the concrete was not blown by water jet with 8 to 24 ml of retarder because of hydration of cement, hence the surface quality was poor. Therefore, washing timing of one day after concrete placement showed 90 % of aggregate exposed rate and 24 ml of retarder showed the most favorable result of aggregate exposure.

• Journal of the Korean Ceramic Society
• /
• v.52 no.1
• /
• pp.28-32
• /
• 2015

In this article, the influence of a hydrolyzed wheat protein retarder on the hydration process, ion concentration in liquid phase, degree of supersaturation, and crystal morphology of plaster was investigated. Furthermore, the retarding mechanism and the strength loss of gypsum were also studied by scanning electron microscopy (SEM). The results indicate that the use of the hydrolyzed wheat protein retarder for plaster achieved a better retarding effect and lower strength loss. The combination of gypsum plaster with the retarder not only decreased the plaster's early hydration rate and prolonged its setting time efficiently, but also militated against the crystal morphology of dihydrate gypsum. For example, the crystal dimensions changed little, but the proportion of needle-shaped crystals decreased. Combination with calcium ions on the surface of dihydrate gypsum crystal nuclei may form a chemisorbed layer, reduce the surface energy of the crystal nuclei, and inhibit the growth of the crystal nuclei of dihydrate gypsum. Consequently, the hydration process of building gypsum becomes greatly extended and is slowed down significantly.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.05a
• /
• pp.34-35
• /
• 2016

Most of the construction adhesive may contain harmful component to the human body with an organic adhesive. In addition, when the adhesive caused hydroquinone, alkyl benzophenone, etc, also it raises the skin diseases to workers. Therefore, the inorganic adhesive development is necessary. This study was a study to know adhesive strength properties that adhesive using a magnesium oxide according to the addition ratio of the retarder. It has experiments to two types of magnesium oxide and type and ratio of retarder differently.

• International Journal of Concrete Structures and Materials
• /
• v.8 no.1
• /
• pp.61-68
• /
• 2014

This paper reports the physical properties and hydration products of slag cement that was prepared by activating ground granulated blast furnace slag with commercial lime and plaster of Paris (POP) as activators. The consistency, setting times and soundness of various mixes of slag-lime-POP is reported. The hydration products and formation of bonds in the paste during setting were studied with the help of SEM, FTIR and XRD tests and the same are correlated to the hydration process. The setting times of the mixes are found to be lower than that of the value prescribed for ordinary Portland cement (OPC). Borax is used as a setting retarder and a borax content of 0.4 % by mass gives setting times that are normally prescribed for OPC. In the early stages of setting C-A-S-H gels are found in this cementing material instead of C-S-H gel, as generally observed in the OPC.

• Journal of the Korea Concrete Institute
• /
• v.25 no.2
• /
• pp.201-207
• /
• 2013

When hot weather concrete is utilized, the cooling methods of cooling pipe, liquid nitrogen, ice, etc., are used to prevent the poor consistency and cold joint due to high temperature. These methods, however, spike the production cost and energy consumption, and make quality control difficult. Among these methods is one that involves the use of a retarder. Although economical, retarder is caused difficulty of retarded hardening and setting time control due to inaccurate weighing and poor working condition. Therefore, how to make a tablet for hot weather concrete, as with the existing pharmacy and foods, is discussed in this study, including the following items: mortar setting time, flow test by elapsed time, physical and mechanical properties of concrete. As a result, gluconic acid is superior to lignosulfonic acid and the possibility of using them for such purpose without quality degradation was confirmed in this study, when retarder is tabletting.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.78-79
• /
• 2013

As a part of study to maximize the amount used of the ground granulated blast-furnace slag, the study deals with setting properties of paste that is mixed the ground granulated blast-furnace slag with CaO-Al₂O₃ based inorganic blinder. The results of the experiment show that the setting time is most fast in the mix of 25% rate of CaO-Al₂O₃ based inorganic blinder. It is generally needed 2 hours for work time in precast concrete products. In this study, this requirement is achieved when using the retarder of 0.5%.

• Journal of the Korean Ceramic Society
• /
• v.33 no.3
• /
• pp.307-312
• /
• 1996

In following addition of 0.3, -0.6, 0.8, 1.0 and 5 weight percent MgSiF66H2O studies have been made of the setting and hardening characteristics of ordinary portland cement. MgSiF66H2O retarded the setting time of ordinary portland cement and extended the induction pariod of the hydration. In ordinary portland cement the setting characteristics were drastically altered especially at high MgSiF66H2O contents. Evidence was also obtained by the formation of a KSiF6 which was very fine particle. The results wee as follows. 1. Slump was slightly decreased when MgSiF66H2O added. 2. Setting time was retarded depending on the amount of retarding agent 2 to 8 hours 3. Compressive strength was almost same or some increased in comparision with opc. 4. When MgSiF66H2O was added to cement paste K2SiF6 were formed It was fine-sized distributed uniformly in cement grain and caused retardation of cement setting.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.3
• /
• pp.237-243
• /
• 2015

In this research, isothermal conduction calorimetry analysis has been conducted to investigate the reactivity of alkali activated slag binders. In order to secure the reactivity and workability of alkali activated slag binders, experiences with various types and concentrations of alkali activators were performed. Isothermal conduction calorimetry were measured with different alkali activators and mass ratio of $SO_3$ to binders as variables, and sodium tripolyphosphate ($Na_2P_3O_{10}$) and hydrated sodium borate ($Na_2B_4O_710H_2O$) were used to control setting time. As a results, alkali activated slag binders required alkali activators with 4 to 5 percent of concentration to accelerate the formation of calcium silicate hydrate(C-S-H) by alkali-activation, and overall heat generation rate delayed as accumulated heat decreased due to the high $SO_3$ contents. Moreover, the use of hydrated sodium borate as setting retarder causes elongated setting time due to delaying heat generation, so it can be considered that setting retarder played an important role in delaying total heat generation rate.

• Journal of the Korean Ceramic Society
• /
• v.21 no.4
• /
• pp.355-360
• /
• 1984

The effect of 2% of $P_2O_5$ substituted in gypsum(5 mol% as $HPO_3$) on the early hydration characteristics of $C_3A$ were investigated and then gypsum only and gypsum mixed with $Ca(H_2PO_4)_2$.$H_2O$(2% as $P_2O_5$) were studied separately for comparison. The early hydration reaction of $C_3A$ with each gypsum were examined by measuring the rate of heat libera-tion of hydration with calorimeter and by analysing the hydration products with X-ray diffractometer and differential thermal analyser. It was shown that phosphogypsum substituted with $P_2O_6$ in the crystal lattice accelerated exceedingly the formation of the ettrignite and following hydrated products. However the other gypsum especially gypsum without any phosphate delayed the formation of various hydration products, It was consequently suggested that when phosphogypsum are used as the retarder of cement setting its reta-rding effect for setting of cement is not ascribed to the retardation of ettringite formation.

• Journal of the Korean Ceramic Society
• /
• v.34 no.4
• /
• pp.399-405
• /
• 1997

With the increase of ZnO content, heat of hydration decreased. For specimens containing ZnO more than 0.6 wt.%, the compressive stength of cement cured for 28 days could not be measured because setting was not occurred. With the increase of ZnO content, Blaine specific surface area of cement was decreased and the residue of 45 ${\mu}{\textrm}{m}$ and 90 ${\mu}{\textrm}{m}$ was increased when cement was ground. That is, grindability became worse as ZnO increased in clinker. The difference of color as a function of ZnO content could not be observed, but in the excess of amount of ZnO added, color became more white and reddish yellow.