• KEPCO Journal on Electric Power and Energy
• /
• v.2 no.4
• /
• pp.609-613
• /
• 2016

A hybrid charging method with serial and parallel architecture has been developed to resolve the unbalanced charge problem among battery cells for Electric Vehicles. In this method, the major charging is performed with serial part and the balancing is carried out with the parallel part, where the serial part is big and heavy but the parallel part is smaller and lighter than serial part. A sensor array to detect the individual battery cell voltage, duty rate control incorporated IGBTs, and battery management system are employed as the core parts of the proposed system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.4
• /
• pp.273-279
• /
• 1998

In this paper, the proposed charging system consists of step charging mode and time-sharing equalization charging mode. As $\Delta$V=O point is detected, the proposed cut-off method will selectively cut off the only battery to reach the $\Delta$V=O point, preventing serial-connected batteries from undercharging. In the start of each step, the equalization charging mode is performed to reduce the capacity difference among the batteries. Though it is added to simple circuit for selective cut-off, comparing with recently used step-charging method, this system can improve the life cycle of battery and charging efficiency, and be also very effective for preventing the batteries from overcharging and undercharging.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.554-559
• /
• 1998

Equalizing the state of charge of cell that affects the charge/discharge quality and efficiency of the battery through the charge/discharge characteristic experiments of battery source, we develope the high efficiency charge/discharge system which would be used in serial HEV with the constant engine-generator output. For this, establishes the electrical model of Ni-MH battery appropriate to the high efficiency charge/discharge conditions. There is no model of Ni-MH cell, so we used Ni-Cd model and obtain the Ni-MH model through the experiment. A reason that each cell has the same charge/discharge property for applying the cell model to serial/parallel connected battery source extensively is needed. Therefore, in this paper, propose the Ni-MH charger/discharger has the equalization charging function and selectable cut-off function.

• Journal of Sensor Science and Technology
• /
• v.25 no.2
• /
• pp.155-159
• /
• 2016

In this work, we have developed a test system to examine whether the charge indicator of the plug-in hybrid electric vehicle (PHEV) works properly or not. In PHEV, the driver should charge the necessary electricity by plugging in manually and be able to know the charging status through the charge indicator conveniently located for the charging individual. Our system used the CAN bus to transmit the same commands from ECU to the indicator to test the proper operation of the indicator lights. It measured the electric current values during operation and analyzed to determine the quality of the indicators. The inspection items included the proper packaging, the electrical shorts, the LED lighting during charging, the LED lighting for charging failure, and the LED lighting when errors occur. We developed the system for the operators in the factory allowing them to approve the test results at the site. We developed the hardware, the control software, and the software to store the test results and the history of the products in the database. Serial numbers were given to the good quality products and the bar code labels were printed to trace the products afterwards. Through this work, we developed a system to inspect the electric parts in real time upon fabrication. We are planning to further improve our system to inspect the brightness of the indicator by adding the vision inspection in future.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.192-194
• /
• 2006

To elucidate possible challenges for outdoor practical use of dye-sensitized solar cells(DSC), compared with conventional Si solar cells. DSC modules still need the larger area than conventional Si solar modules to attain the same rated output because of lower photoelectron-chemical conversion efficiency. However, using batteries backup systems, the measured data shows that DSCs gathered over 12% more electricity than Si solar cells of the same rated output power in same outdoor condition. Moreover, battery charging time of DSC is about 1 hour faster than same rate of Si solar module. In this paper, 12 single DSC cells prepared for 4 serialized DSC cells was connected in 3 row parallel which have same output power rate of Si solar module. This DSC module was practiced generating characteristic experiment over outdoor daylight condition and applied with PV battery charger by using DC-DC converter. The main advantages of DSC module battery charger as compared with conventional Si solar module one are shorter charge time and lower cost.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.2
• /
• pp.153-160
• /
• 2013

This research paper describes the development of battery charger with a variable output voltage capacity for charging the batteries used in electrical vehicles. The voltage and current accordingly is control via the buck converter that receives three phase current at primary side and fed to bridge rectifier which is comprised of full bridge converter and HFTR(High Frequency Transformer) for isolation and a square wave AC output. The transformer primary side is in series to divide certain charging current and the secondary side is comprised of six fix transformers so that they can generate certain amount of power and various output voltage through relay connection using 6 DC outputs. Moreover, all parallel connected full bridge serial resonant converter communicate together with upper(main) controller. The constructed structure is verified by conducting the test on PSIM as well as experimentally.

• Journal of Magnetics
• /
• v.16 no.3
• /
• pp.246-252
• /
• 2011

A high-voltage power supply has been built for activation of the brain via stimulation using a Full Wave Cockroft-Walton Circuit (FWCW). A resonant half-bridge inverter was applied (with half plus/half minus DC voltage) through a bidirectional power transistor to a magnetic stimulation device with the capability of producing a variety of pulse forms. The energy obtained from the previous stage runs the transformer and FW-CW, and the current pulse coming from the pulse-forming circuit is transmitted to a stimulation coil device. In addition, the residual energy in each circuit will again generate stimulation pulses through the transformer. In particular, the bidirectional device modifies the control mode of the stimulation coil to which the current that exceeds the rated current is applied, consequently controlling the output voltage as a constant current mode. Since a serial resonant half-bridge has less switching loss and is able to reduce parasitic capacitance, a device, which can simultaneously change the charging voltage of the energy-storage condenser and the pulse repetition rate, could be implemented. Image processing of the brain activity was implemented using a graphical user interface (GUI) through a data mining technique (data mining) after measuring the vital signs separated from the frequencies of EEG and ECG spectra obtained from the pulse stimulation using a 90S8535 chip (AMTEL Corporation).

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.882-883
• /
• 2013

With the development of the society, pure electric vehicles will be surely important of the future. Electric vehicle requires various technology like motor driving, battery management, operational efficiencies and so on. Battery management is indeed the most important to enhance battery's performance and life. This paper has deeply discussed and studied on the lithium-polymer battery management system of pure electric vehicle. First of all we have analyzed the characteristic of the lithium-polymer batteries and the factors influenced on the state of charge. Then a logical SOC measuring method has been raised, which is the combination of open circuit voltage and Ah integration. The next we will introduce the design of battery management system, the battery management system performs many functions, such as inspecting the whole process, when it's running cell equalization protecting and diagnosing the battery, estimating the state of charge. The module design style including microcontroller, data aquisition module, charging control module and serial communication module. To arrive at conclusions, the battery management system which this paper has introduced is reliable and economical.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.207-210
• /
• 2005

This paper describes a design of several ship's emergency lighting system(SELS) that power factor is improved and power is controlled extensively, and techniques to control and monitor this system in remote distance by PC serial communication. The remote monitoring control system is composed of emergency power supply system (EPSS), half bridge(HB)inverter, fluorescent lamp(FL), microprocessor, multi communication interface. EPSS checks the voltage of the emergency backup battery in real time. In case that the voltage of 13[V] or less has been detected for 5[msec] or longer for 3 times in a row, charger circuit is connected for battery charging. Experimental works using proposed system confirm that speedy and stable power to be supplied when main power source cut-off, compared with conventional analog type, and input power up to 35.0[%] by adjusting of pulse frequency of the HB inverter.

• The KIPS Transactions:PartA
• /
• v.10A no.4
• /
• pp.419-424
• /
• 2003

Every CP has its own contents classification system for charging. Currently most classification system is based on the CPID and Service ID of the WAP. An service ID from a common CPID pool is provided to CP for each service. Then charges are computed for each service ID. But in this system CPID range must be changed whenever the CP adds a new service. Therefore all CPIDs of the existing services must be updated. Another problem is that when a CP provides several services, it has multiple CPIDS. Therefore with increasing number of services CPID would be exhausted in the future. In this paper, we proposes a new contents ,classification system. We remove CPID range and instead we propose a new CPID composed of a system n, service classification ID and a serial number. The new CPID is assigned to each service. By this scheme we improve the contents classification system.