• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2000.04a
• /
• pp.130-140
• /
• 2000

The earthquake hazard has been evaluated for 10km by 10km area around Kyeongju which is located near Yangsan fault and has abundant historical earthquake records. The ground motion potentials were determined based on equivalent linear analysis by using the data obtained from in situ and laboratory tests and the El centro eartqhuake record scaled to CLE and OLE of the region. The in situ tests include 9 boring investigations 2 crosshole 7 downhole 13 SASW tests and in the laboratory X-ray diffraction analyses and resonant column tests were performed. The peak ground accelerations range between 0.140g and 0.286g on CLE and between 0.051g and 0.116g on OLE respectively showing the good potential of amplification in the deep alluvial layer which is common in Kyeongju area. the response spectrum based on the Korea design guide was sometimes underestimate the motion. particularly near the natural period of the site and the importance of site-specific analysis and need for the improved site categorization method were introduced.

• Industrial Engineering and Management Systems
• /
• v.13 no.3
• /
• pp.297-303
• /
• 2014

Stock pre-positioning is one of the most important decisions for preparing the stage of emergency logistics planning. In this paper, a mixed integer model for stock pre-positioning is derived to support an emergency disaster relief response against the event of earthquake. A maximum response time limit, budget availability, multiple item types, and capacity restrictions are considered. In the model, the decision of the distribution centers to cover a disaster area and the amount of supplies to be stocked in each distribution center are simultaneously determined to maximize the total expected relief demand of the disaster areas covered by the existing distribution centers. The proposed model is applied to a real case with 33 disaster areas and 16 distribution centers in Indonesia. Several sensitivity analyses are conducted to estimate the fluctuation on the emergency stock pre-positioning planning by changing the maximum response time and budgets.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.5 no.4
• /
• pp.87-94
• /
• 1985

Dynamic analysis of guyed tower is presented in this paper. The scope of the study is twofold. The one is to determine an efficient analysis method to include the nonlinearity of the mooring system and the nonlinear hydrodynamic wave forces. The other is to investigate the sensitivity of two major design parameters, that is the stiffness of mooring system and the fixity condition of the tower at mud line. Time history analysis method utilizing mode superposition is mainly considered. However several other methods are also used for the purpose of comparison. Analyses are carried out using the Lena Guyed Tower, which is the first structure of this kind, as a standard structure.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1995.04a
• /
• pp.73-81
• /
• 1995

In Korea, the pilot construction of the first high-speed railroad on the Seoul-Pusan has already started 2 years ago. In the thesis, an attempt is made to develop reliability-based integrity-assessment models for the computer-aided control and maintenance of high-speed railroad bridges. The strength limit state models for PC railroad bridges encompass the bending and shear strengths as well as the strength interaction equations which simultaneously take into the element and system reliablities of the proposed limit states and reliability models. Then, the actual load carrying capacity and the realistic safety of bridges are evaluated using the system reliability-based equivalent strength, and the results are compared with those of the element reliability-based or conventional methods. Various parametric studies are performed for the proposed reliability-based safety and integrity-assessment models using the actual PC box girder bridges used in the pilot construction. And the sensitivity analyses are performed for the basic random variables included in strength limit state models. It is concluded that proposed models may be practically applied for the rational assessment of safety and integrity of high speed railroad bridges.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.422-427
• /
• 2008

This study is to illustrate the usefulness of Kriging Dimension Reduction Method(KDRM), which is to construct probability distribution of response function in the presence of the physical uncertainty of input variables. DRM has recently received increased attention due to its sensitivity-free nature and efficiency that considerable accuracy is obtained with only a few number of analyses. However, the DRM has a number of drawbacks such as instability and inaccuracy for functions with increased nonlinearity. As a remedy, Kriging interpolation technique is incorporated which is known as more accurate for nonlinear functions. The KDRM is applied and compared with MCS methods in a compression coil spring design problem. The effectiveness and accuracy of this method is verified.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.6
• /
• pp.3437-3442
• /
• 2013

The high incidence of gastric cancer and consequent mortality pose severe threats to human health. Early screening, diagnosis and treatment are the key to improve the prognosis of the patients with gastric cancer. Gastroscopy with biopsy is an efficient method for the diagnosis of early gastric cancer, but the associated discomfort and high cost make it difficult to be a routine method for screening gastric cancer. Serum tumor marker assay is a simple and practical method for detection of gastric cancer, but it is limited by poor sensitivity and specificity. Therefore, people have been looking for novel serum markers of gastric cancer in recent years. Here we review the novel serum tumor markers of gastric cancer and their diagnostic significance, focusing on the discoveries from serum proteomics analyses and epigenetics researches.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.6
• /
• pp.153-163
• /
• 1996

An expert system to design compressor valve systems has been developed. Design process is viewed as a chain of devisions based on the results of necessary analyses. Actual design is implemented by the interaction between the expert system and the user. In this work, it is demonstrated how a final design is achieved by utilizing the rule bases and analysis capability of the system. The structure of the rule bases and related parameter studies are also explained. Advantages of using an expert system approach for valve designs are explained using a practical example.

• Journal of Korean Society for Quality Management
• /
• v.29 no.3
• /
• pp.49-65
• /
• 2001

This paper presents new compromise ALT plan which is applied to situations that true relationship between stress and parameters is not known exactly. The assumed failure distribution of this study is one of location-scale family, i. e., exponential, Weibull, and lognormal distributions which have been ones of the popular choices of failure distributions. The method of applying the stress is constant, and the censoring mechanism is Type I censoring. Compared with existing compromise plans under true simple linear model in terms of statistical efficiency, the efficiency of new compromise plan is better than the corresponding other compromise ones in most cases. For case when true model is quadratic, this plan can be used without any severe loss in statistical efficiency. The proposed new compromise ALT plan is illustrated with a numerical example and sensitivity analyses are conducted to study effects of pre-estimates of design parameters.

• Journal of Korean Society for Quality Management
• /
• v.36 no.2
• /
• pp.20-27
• /
• 2008

Tolerance design has been identified as an important research area and a number of models have been proposed in the literature. This paper investigates the effect of limited capacity on tolerance design for products with nominal-the-best type (N-type) quality characteristics. The model is developed under the assumption that the reprocessed and nonreprocessed items are produced by the same manufacturing process and therefore their quality characteristics are identically and independently distributed. Profit models are constructed which involve four price/cost components; selling price, cost incurred by imperfect quality, reprocessing and quality inspection costs. Methods of finding the optimal tolerance limits are presented, and a numerical example is given. Sensitivity analyses are also performed to study the effect of a process standard deviation on this model.

• Journal of Korean Society for Quality Management
• /
• v.32 no.4
• /
• pp.156-168
• /
• 2004

This research investigates the statistical efficiency of variable sampling size & sampling interval(VSSI) $\bar{X}$ charts under two assignable causes. Algorithms for calculating the average run length(ARL) and average time to signal(ATS) of the VSSI $\bar{X}$ chart are proposed by employing Markov chain method. States of the process are defined according to the process characteristics after the occurrence of an assignable cause. Transition probabilities are carefully derived from the state definition. Statistical properties of the proposed chart are also investigated. A simple procedure for designing the proposed chart is presented based on the properties. Extensive sensitivity analyses show that the VSSI $\bar{X}$ chart is superior to the VSS or VSI $\bar{X}$ chart as well as to the Shewhart $\bar{X}$ chart in statistical sense, even tinder two assignable causes.