• 한국세라믹학회지
• /
• 제32권8호
• /
• pp.945-949
• /
• 1995

In order to investigate the performance of compression-type accelerometer on piezoelectric properties, PZT materials have been studied. The ring-shaped piezoelectric elements were prepared using commercial PZT powders by conventional ceramic process. Their estimated relative dielectric constant, piezoelectric charge constant (d33) and voltage constant (g33) values showed 390∼3400, (90∼593)×10-12 C/N and (19.5∼40.5)×10-3 V-m/N, respectively. The charge sensitivity of accelerometer is proportional to the piezoelectric charge constant value (d33) of PZT, but its voltage sensitivity is related with the piezoelectric voltage constant (g33). Since the mounted resonance frequency and sensitivity are dependent on the seismic mass as well as physical charateristics and size of PZT elements, the suitable considerations between two components are required for accelerometer's design.

• 대한기계학회논문집
• /
• 제19권10호
• /
• pp.2678-2689
• /
• 1995

In this study, a new hot-wire anemometer which has greater sensitivity than that of a constant temperature anemometer (CTA) was proposed. In contrast to CTA, the wire working resistance of the new anemometer increases with flow velocity, that is, the operating mode of the wire becomes variable temperature. The variable temperature anemometer(VTA) was made by substituting a voltage controlled variable resistor such as photoconductive cell or transistor for one of the resistors in the bridge. By positively feeding back the bridge top signal to the input side of these electronic components, the wire overheat ratio could be increased with velocity automatically. Static response analyses of the VTA, constant voltage anemometer (CVA) and CTA were made in detail and calibration experiments were performed to validate the proposed operating principle. The wire operating resistance of the CVA decreases with velocity and this leads to lower sensitivity than that of a CTA. But the sensitivity of the newly proposed VTA is superior to that of a CTA, since the wire overheat ratio increases with velocity. Consequently, it is found that the major factor that is responsible for large sensitivity of a VTA is not the working resistance itself but the change of the wire working resistance with velocity.

• 제어로봇시스템학회논문지
• /
• 제10권4호
• /
• pp.295-303
• /
• 2004

Previously it has been shown that the all pole systems resulting good time responses can be characterized by so called K-polynomial. The polynomial is defined in terms of the principal characteristic ratio $\alpha_1$ and the generalized time constant $\tau$ . In this paper, Part II presents several sensitivity analyses of such systems with respect to $\alpha_1$ and $\tau$ changes. We first deal with the root sensitivity to the perturbation of $\alpha_1$ . By way of determining the unnormalized function sensitivity, both time response sensitivity and frequency response sensitivity are derived. Finally, the root sensitivity relative to $\tau$ change is also analyzed. These results provide some useful insight and background theory when we select of and l to compose a reference model of which denominator is a K-polynomial, which is illustrated by examples.

• 동력기계공학회지
• /
• 제16권2호
• /
• pp.11-16
• /
• 2012

In this paper, the authors formulate the sensitivity analysis algorithm for the natural frequency of a torsional shafting by expanding the transfer stiffness coefficient method. The basic concept of the present algorithm is based on the transfer of sensitivity stiffness coefficient, which is the derivative of stiffness coefficient with respect to design parameter, at every node from the first node to the last node in analytical model. The effectiveness of the present algorithm is confirmed by comparing the results of the sensitivity analysis and those of the reanalysis for the natural frequencies of a torsional shafting with a constant cross section. In numerical calculation, the design parameter is the diameter of the shaft element of the torsional shafting.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1358-1363
• /
• 2004

The objective of this work is to propose calibration facility in which a thin film type heat flux sensor can be calibrated under convective flow condition by using a small wind tunnel with the constant temperature plate condition. A small wind tunnel has been built to produce a boundary layer shear flow above a constant temperature copper plate. 12-independent copper blocks, thin film heaters, insulators and temperature controllers were used to keep the temperature of flat plate constant at a specified temperature. Three commercial thin film-type heat flux sensors were tested. Convective calibrations of these gages were performed over the available heat flux range of $1.4{\sim}2.5kW/m^2$. The uncertainty in the heat flux measurements in the convective-type heat flux calibration facility was ${\pm}2.07%$. Non-dimensional sensitivity is proposed to compare the sensitivity calibrated by manufacturer and that of experiment conducted in this study.

• Journal of Microbiology and Biotechnology
• /
• 제16권11호
• /
• pp.1760-1772
• /
• 2006

Mature acetylcholinesterase (AChE) gene (gm, 1,836 bp) was cloned from the housefly and successfully expressed in the E. coli CodonPlus (DE3) RIL system (GM-E, 72 kDa) with a yield of 1,630 mU/g fresh cells. Using the gm, 10 kinds of mutants were constructed and expressed for enhancing sensitivity to insecticides. The sensitivity of these mutants to five kinds of organophosphate (OP) and three carbamate insecticides was investigated by measuring the apparent bimolecular inhibition constant ($k_i=k_2/K_d$). Surprisingly, the sensitivity of quadruple mutant IGFT was enhanced as much as 7-fold for acephate, 164-fold for demeton-S-methyl, 484-fold for dichlorvos, 523-fold for edifenphos, 30-fold for ethoprophos, 30-fold for benfuracarb, 404-fold for carbaryl, and 107-fold for furathiocarb, compared with that of GM-E, although the sensitivity of each single point mutant was slightly increased. These mutational studies indicated that (i) contradictory to Walsh et al. [39], the residue 327 is the important key residue for enhancing sensitivity as much as the residue 262, (ii) the residue 82 and additional residues of 234, 236, and 585 are also important, and (iii) sensitivity was cooperatively accelerated as the number of strategic mutations increased.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.317-318
• /
• 2012

• 산업공학
• /
• 제7권3호
• /
• pp.193-199
• /
• 1994

The purpose of this paper is to develop a method of the sensitivity analysis that can be applicable to a degenerate tree solution of the minimum cost flow problem. First, we introduce two types of sensitivity analysis. A sensitivity analysis of Type 1 is the well known method applicable to a spanning tree solution. However, this method have some difficulties in case of being applied to a degenerate tree solution. So we propose a sensitivity analysis of Type 2 that keeps solutions of upper bounds remaining at upper bounds, those of lower bounds at lower bounds, and those of intermediate values at intermediate values. For the cost coefficient, we present a method that the sensitivity analysis of Type 2 is solved by using the method of a sensitivity analysis of Type 1. Besides we also show that the results of sensitivity analysis of Type 2 are union set of those of Type 1 sensitivity analysis. For the right-hand side constant or the capacity, we present a simple method for the sensitivity analysis of Type 2 which uses arcs with intermediate values.

• Tribology and Lubricants
• /
• 제29권3호
• /
• pp.160-166
• /
• 2013

There is an indispensable need for force calibration for quantitative nanoscale force measurement using atomic force microscopy. Calibrating the normal force is relatively straightforward, whereas doing so for the lateral force is often complicated because of the difficulty in determining the optical lever sensitivity. In particular, the lateral force calibration of a colloidal probe in a liquid environment often has a larger uncertainty as a result of the effects of the epoxy, the location of the colloidal particle on the cantilever, and a decrease in the quality factor. In this work, the lateral force of a colloidal probe using a reference cantilever with a known spring constant was calibrated in a liquid environment. By obtaining the spring constant and the lateral sensitivity at the equator of a spherical colloidal particle, the damage to the bottom surface of the colloidal particle could be eliminated. Further, it was shown that the effect of the contact stiffness on the determination of the lateral spring constant of the cantilever could be minimized. It was concluded that this method can be effectively used for the lateral force calibration of a colloidal probe in a liquid environment.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제3권2호
• /
• pp.161-171
• /
• 1999

Aerodynamic sensitivity analysis codes are developed via the hand-differentiation using a direct differentiation method and an adjoint method respectively from discrete two-dimensional compressible Navier-Stokes equations. Unlike previous other researches, Baldwin-Lomax algebraic turbulence model is also differentiated by hand to obtain design sensitivities with respect to design variables of interest in turbulent flows. Discrete direct sensitivity equations and adjoint equations are efficiently solved by the same time integration scheme adopted in the flow solver routine. The required memory for the adjoint sensitivity code is greatly reduced at the cost of the computational time by allowing the large banded flux jacobian matrix unassembled. Direct sensitivity code results are found to be exactly coincident with sensitivity derivatives obtained by the finite difference. Adjoint code results of a turbulent flow case show slight deviations from the exact results due to the limitation of the algebraic turbulence model in implementing the adjoint formulation. However, current adjoint sensitivity code yields much more accurate sensitivity derivatives than the adjoint code with the turbulence eddy viscosity being kept constant, which is a usual assumption for the prior researches.