• 한국소음진동공학회논문집
• /
• 제15권6호
• /
• pp.764-771
• /
• 2005

This study investigates the 3-axis transmissibility of the vehicle compact disk player's mainbase which is supported by dampers and springs. These dampers and springs as the important element ' determining the vibration performance of vehicle compact disk Player are used to minimize the vibration which is induced by driving the vehicle. In order to determine the analysis frequency band, we investigated the excitation frequency of road from the vehicle test. As the characteristics of damper and spring were changed, we carried out the vibration test and investigated the change of transmissibility, Also, we carried out the sensitivity analysis for transmissibility and we found out that the properties of damper were the dominant element in the vibration performance of vehicle compact disk player.

• 소음진동
• /
• 제8권2호
• /
• pp.346-352
• /
• 1998

This paper presents actuating characteristics of an asymmetric high-speed optical pick-up fine actuator that can be installed in a small area such as a notebook personal computer. In the asymmetric actuator four points (mass center, actuation center, supporting point of wire suspension on a bobbin, and optical axis) are not coincident so that the proposed actuator suspension reveals undesirable suspension resonance in the pitch and yaw direction. Lumped parameter dynamic model in each direction is used to investigate the driving characteristics with respect to relative location of the four points. Some of desired design directions toward reducing resonance peaks are suggested by using sensitivity information. In order to avoid undesirable resonance, at least supporting point on the obbin must be located in the middle of the mass and actuation center of the asymmetric pick-up actuator.

• Advances in Computational Design
• /
• 제1권4호
• /
• pp.357-370
• /
• 2016

This paper aims to examine the dynamic response of a newly designed ultrasonic motor under half-sine shock impulses. Impact shock was applied to the motor along x, y or z axis respectively with different pulse widths to check the sensitivity of the motor to the shocks in different directions. Finite Element Analysis (FEA) with the ANSYS software was conducted to obtain the relative displacement of a key point of the motor. Numerical results show that the maximum relative displacement is of micro meter level and the maximum stress is five orders smaller than the Young's modulus of the piezo material, which proves the robustness of the motor.

• 전자공학회논문지C
• /
• 제34C권5호
• /
• pp.33-42
• /
• 1997

In this paper, the modified inverse chebyshev low-pass function is analyzed in the frequency domain, time domain, and sensitivity characteristics as compared with the classical inverse chebyshev function. Unlike the classical function, the modified function exhibits progressively diminishing ripples in the stopband. So, the modified function has a great attenuation throughout the stopband except at the vicinity of a stop frequency and can be realizable in the passive doubly-terminated ladder network for the even order. The poles of the modified function move towards real axis by the effect of diminishing ripples. Thus the pole-Q, which is one of the valuable measurements to estimage the function characteristics, is reduced without increasing order. In the frequency and can be realizable in the passive doubly-terminated ladder network to examine the magnitude and pole-Q sensitivities.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.539-542
• /
• 1997

We present a micro-positioning stage that has minimized geometrical error and can drive in the 4-axis. This stage divided into two parts: $Z\theta_x$ $\theta_y$, motion stage and$\theta_z$ motion stage. These stages are constructed in flexure hinges, piezoelectric actuators and displacement scnsors. The dynamic model for each stage is obtained and their FE (finite element) models are made. Using the Lagrange's equation, the motion of equation is found. Through the parametric analysis and FE analysis, sensitiv~ty of the design parameters is executed. Finally, fundamental frequencies, maximum stress, and displacement sensitivity for each stage are obtained. We expect that this micro-positioning stage be a useful micro-alignment device for various applications.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.685-686
• /
• 2015

This paper describes design results of the measurement system to test the properties of broadband AC magnetic field sensors used in weapon system. This measurement system consists of 3-axis helmholtz coil, signal generator, signal amplifier, sensor data acquisition unit and measurement & analysis controller including the operating software. This system is able to measure various properties of AC magnetic field sensor such as sensitivity, linearity and dynamic response in the frequency of 1 Hz to 10 kHz. The performance of this system was verified by measuring and analyzing the property of a MAG 639, standard magnetic field sensor of bartington instruments, with this developed system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 C
• /
• pp.1714-1716
• /
• 2002

Optical fiber sensor is a subject which has been attracted considerable attention in recent year. Especially, it is being developed for the detection and location of partial discharge in oil-filled transformers. In this paper, we propose and experimentally demonstrate directivity and sensitivity of a hollow cylindrical mandrel sensor. The sound source is a PZT actuator of hollow cylinder type. Several layers of the fiber laminated around the mandrel surface and experiments were performed on three axis modes. The experimental results can be applied to analyze detected signals optimally.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.361-365
• /
• 2002

In this paper, a magnetic suspension system with inductive sensors fur a high vacuum turbomolecular pump(TMP) is discussed. The performance of designed inductive position sensor is evaluated by static and dynamic test, and the test results show sensitivity of about 6,000 V/m and dynamic bandwidth of 750 ㎐. The protype of magnetic suspension system is designed and constructed with 5-axis magnetic bearing, inductive sensor and BLDC internal motor. With DSP based digital PID control system, the prototype is examined its high damping ratio and stable operation up to 20,000 rpm of rotation.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.989-992
• /
• 2002

This paper presents a procedure far design, modeling and analysis of a fine positioning stage. The stage considered here is composed of flexure hinges, piezoelectric actuators and their peripherals. Through a series of analysis, the structural analysis model is simplified as a rigid body(the moving part) and springs (the flexure hinges). An experimental design procedure is applied to determine optimum design variables for flexure hinges. The optimum variables are validated through a numerical test. A sensitivity analysis on the notch positions is also performed to obtain a guideline of fabrication accuracy for the stage.

• 한국전자파학회논문지
• /
• 제9권2호
• /
• pp.159-170
• /
• 1998

개인 휴대통신 주파수 대역에서 인위적인 전자파 잡음을 공통단자를가지는 평면 배열 3축 안테나를 사용하여 측정하였고, 이 데이터를 통계 확률적인 방법을 이용하여 모델링을 하였다, 측정된 APD 곡선의 변수를 합성근사화 알고리즘을 이용하여 빠른 시간내에 계산이 가능하게 하였다. 진폭확률분포에 관한 모형변수의 계산결과는 전자파 환경의 데이터 베이스의 저장용량을 감소시킬 수 있으며, 또한 송.수신기의 출력 및 감도의 마진 결절에 기초적인 자룔로 이용이 가능할 것이다.