• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.223-224
• /
• 2008

Important element are low cost, high-efficiency crystalline silicon solar cells. in this paper, Will be able to contribute in low cost, high-efficiency silicon solar cells, Applies oxide/nitride passivation, produced screen-printed solar cells. and the Measures efficiency, and evaluated a justice quality oxide/nitride passivation screen-printed solar cells.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.38.1-38.1
• /
• 2010

The trend to thinner crystalline silicon solar wafers in production of solar cells investigates re-evolution of back surface field (BSF) formation. We have studied mechanisms of back contact formation in Al evaporation and screen printed Al paste for Si solar cells by TEM analysis. We observed that Si diffuse into Al during heat up. The Si diffusion process made vacancies in Si wafer. The Al began to seep into the Si wafer (Al spike). During heat down, the Al spike were shrink which causes the doped region (BSF).

• 한국태양에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.350-355
• /
• 2009

The crysralline silicon solar cell where the solar cell market grows rapidly is occupying of about 85% or more high efficiency and low cost endeavors many crystalline solar cells. The fabricaion process of high efficiency crystalline silicon solar cells necessitate complicated fabrication processes and Ti/Pd/AG contact, This metal contacts have only been used in limited areas in spite of their good srability and low contact resistance because of expensive materials and process. Commercial solar cells with screen-printed solar cells formed by using Ag paste suffer from loe fill factor and high contact resistance and low aspect ratio. Ni and Cu metal contacts have been formed by using electroless plating and light-induced electro plating techniques to replace the Ti/Pd/Ag and screen-printed Ag contacts. Copper and Silver can be plated by electro & light-induced plating method. Light-induced plating makes use the photovoltaic effect of solar cell to deposit the metal on the front contact. The cell is immersed into the electrolytic plating bath and irradiated at the front side by light source, which leads to a current density in the front side grid. Electroless plated Ni/ Electro&light-induced plated Cu/ Light-induced plated Ag contact solar cells result in an energy conversion efficiency of 16.446 % on 0.2~0.6${\Omega}$ cm, $20{\times}20mm^2$, CZ(Czochralski) wafer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.3
• /
• pp.246-251
• /
• 2013

Screen printing is commonly used to form the front/back electrodes in silicon solar cell. But it has caused high resistance and low aspect ratio, resulting in decreased conversion efficiency in solar cell. Recently the plating method has been combined with screen-printed c-Si solar cell to reduce the resistance and improve the aspect ratio. In this paper, we investigated the effect of light induced silver plating with screen-printed c-Si solar cells and compared their electrical properties. All wafers were textured, doped, and coated with anti-reflection layer. The metallization process was carried out with screen-printing, followed by co-fired. Then we performed light induced Ag plating by changing the plating time in the range of 20 sec~5min with/without external light. For comparison, we measured the light I-V characteristics and electrode width by optical microscope. During plating, silver ions fill the porous structure established in rapid silver particle sintering during co-firing step, which results in resistance decrease and efficiency improvement. The plating rate was increased in presence of light lamp, resulting in widening the electrode with and reducing the short-circuit current by shadowing loss. With the optimized plating condition, the conversion efficiency of solar cells was increased by 0.4% due to decreased series resistance. Finally we obtained the short-circuit current of 8.66 A, open-circuit voltage of 0.632 V, fill factor of 78.2%, and efficiency of 17.8% on a silicon solar cell.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.4
• /
• pp.22-25
• /
• 2003

High series resistance due to the presence of glass frit is one of the major problems for screen printed silicon solar cells. Cells having electrical parameters below the prescribed values are usually rejected during solar module fabrication. Therefore, it is highly desirable to improve the electrical parameters of the silicon solar cells and thereby to increase the overall production yield. It was observed that, the performance of low quality mono-crystalline silicon solar cells made by standard screen printing technology could be improved remarkably by novel surface treatment. We have chemically treated the surface using sodium hydroxide (NaOH) and silver nitrate ($AgNO_3$) solutions. NaOH treatment helps to reduce the series resistance by decreasing the presence of excess glass frit on the top silver grid contact. The $AgNO_3$ treatment is used to reduce the series resistance comes from the deposition of silver on the grids by filling the holes present (if any) within the grid pattern.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.272-272
• /
• 2009

Screen-printing metal contact is typically applied to the solar cells for mass production. And metal paste is used widely for rear contact formation of silicon solar cells. However, Screen-printing solar cell metal paste contact has low aspect ratio, low accuracy, high resistivity, hard control of unclean process. In this paper is to develop resistivity of rear contact for silicon solar cells applications. 4-point prove result, This resistivity of rear contact by Al evaporation was measured about $3.56{\times}10^6{\Omega}{\cdot}cm$ less than screen printed solar cell about $52.6{\times}10^6{\Omega}{\cdot}cm$.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.04a
• /
• pp.225-229
• /
• 2009

The front metal contact is one of the most important element influences in efficiency in the silicon solar cell. First of all selective of the material and formation method is important in metal contacts. Commercial solar cells with screen-printed contacts formed by using Ag paste process is simple relatively and mass production is easy. But it suffer from a low fill factor and a high shading loss because of high contact resistance. Besides Ag paste too expensive. because of depends income. This paper applied for Ni/Cu metallization replace for paste of screen printing front metal contact. Low cost Ni and Cu metal contacts have been formed by using electroless plating and electroplating techniques to replace the screen-printed Ag contacts. Ni has been proposed as a suitable silicide for the salicidation process and is expected to replace conventional silicides. Copper is a promising material for the electrical contacts in solar cells in terms of conductivity and cost. In experiments Ni/Cu metal contact applied same grid formation of screen-printed solar cell. And it has variation of different grid spacing. It was verified that the wide spacing of grid finger could increase the series resistance also the narrow spacing of grid finger also implies a grid with a higher density of grid fingers. Through different grid spacing found alteration of efficiency.

• Current Photovoltaic Research
• /
• v.10 no.3
• /
• pp.90-94
• /
• 2022

The screen-printing method is the most mature solar cell fabrication technology, which has the advantage of being faster and simpler process than other printing technology. A front metallization printed through screen printing influences the efficiency and manufacturing cost of solar cell. Recent technology development of crystalline silicon solar cell is proceeding to reduce the manufacturing cost while improving the efficiency. Therefore, screen printing requires process development to reduce a line width of an electrode and decrease shading area. In this paper, we will discuss the development trend and prospects of screen-printing metallization using metal paste, which is currently used in manufacturing commercial crystalline silicon solar cells.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.56-59
• /
• 2011

The process conditions for high efficiency industrial crystalline Si solar cells with selective emitter were optimized. In the screen printed solar cells, the sheet resistance must be 50-60V/sq. because of metal contact resistance. But the low sheet resistance causes the increase of the recombination and blue response at the short wavelength. Therefore, the screen printed solar cells with homogeneous emitter have limitations of efficiency, and this means that the selective emitter must be used to improve cell efficiency. This work demonstrates the feasibility of a commercially available selective emitter process, based on screen printing and conventional diffusion process. Now, we improved cell efficiency from 18.29% to18.45% by transition of heavy emitter pattern and shallow emitter doping condition.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.490.2-490.2
• /
• 2014

Since the general solar cells accept sun light at the front side, excluding the electrode area, electrons move from the emitter to the front electrode and start to collect at the grid edge. Thus the edge of gridline can be important for electrical properties of screen-printed silicon solar cells. In this study, the improvement of electrical properties in screen-printed crystalline silicon solar cells by contact treatment of grid edge was investigated. The samples with $60{\Omega}/{\square}$ and $70{\Omega}/{\square}$ emitter were prepared. After front side of samples was deposited by SiNx commercial Ag paste and Al paste were printed at front side and rear side respectively. Each sample was co-fired between $670^{\circ}C$ and $780^{\circ}C$ in the rapid thermal processing (RTP). After the firing process, the cells were dipped in 2.5% hydrofluoric acid (HF) at room temperature for various times under 60 seconds and then rinsed in deionized water. (This is called "contact treatment") After dipping in HF for a certain period, the samples from each firing condition were compared by measurement. Cell performances were measured by Suns-Voc, solar simulator, the transfer length method and a field emission scanning electron microscope. According to HF treatment, once the thin glass layer at the grid edge was etched, the current transport was changed from tunneling via Ag colloids in the glass layer to direct transport via Ag colloids between the Ag bulk and the emitter. Thus, the transfer length as well as the specific contact resistance decreased. For more details a model of the current path was proposed to explain the effect of HF treatment at the edge of the Ag grid. It is expected that HF treatment may help to improve the contact of high sheet-resistance emitter as well as the contact of a high specific contact resistance.