• Journal of the Korean Vacuum Society
• /
• v.19 no.5
• /
• pp.326-330
• /
• 2010

The surface oxidation of magnesium was performed by burning and PEO treatment method. The scanning electron microscopy (SEM), EDS, and I-V characteristics have been applied to the study of the oxidation status. The sample formed by buring method shows weaker corrosion-resistant property than that by PEO method, but this shows more conducting property.

• Journal of the Korean Society for Heat Treatment
• /
• v.37 no.2
• /
• pp.79-85
• /
• 2024

The effects of annealing heat treatment and the addition of Cu element on the shape memory effect of the NiTi-based alloy were investigated by analyzing differential scanning calorimeter results and characterizing recovery rate through 3D scanning after Vickers hardness test. Through 3D scanning of impressions after Vickers hardness test, the strain recovery rates for specimens without annealing treatment and annealed specimens at 400, 450, and 500℃ were measured as 45.96%, 46.76%, 52.37%, and 43.57%, respectively. This is because as the annealing temperature increases, both B19' and NiTi₂ phases, which can impede martensitic transformation, are incorporated within the NiTi matrix. Particularly, additional phase transformation from R-phase to B19' observed in specimens annealed at 400 and 450℃ significantly contributes to the improvement in strain recovery rates. Additionally, the results regarding the Cu element content indicate that when the total content of Ni and Cu is below 49.6 at.%, the precipitation of fine B19' and NiTi₂ phases within the matrix can greatly influence the transformation enthalpy and temperature range, resulting in relatively lower strain recovery rates in NiTi alloys with a small amount of Cu element produced in this study.

• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.1
• /
• pp.32-43
• /
• 1995

Ti-6Al-4V alloy are widely used in chemical and aircraft industries for their good corrosion resistance and high strength to weight ratio. Surface alloying of Ti alloy by $CO_2$ laser is able to produce few hundred micrometers thick TiN surface-alloyed layer with high hardness on the substrate very simplely by injecting reaction gas($N_2$) into a laser-generated melt pool and adjust the hardness to the specific requirements of the individual application by changing of laser processing parameters. This research has been investigated the effect of such parameters on TiN surface-alloying of Ti-6Al-4V alloy by $CO_2$ laser. The maximum hardness of TiN surface-alloyed zone waw obtained by injecting 100% $N_2$ gas and it was decreased as the amount of $N_2$ gas in Ar and $N_2$ gas mixture was decreased. As scanning speed was increased, the hardness and depth of TiN surface-alloyed zone was decreased at constant laser power. The surface hardness after double scanning laser treatment is higher than that of single scanning. At constant laser power, the surface roughness is increased after the surface alloying if laser scanning speed is decreased.

• Nuclear Engineering and Technology
• /
• v.54 no.3
• /
• pp.1016-1023
• /
• 2022

In proton therapy, a highly conformal proton dose can be delivered to the tumor by means of the steep distal dose penumbra at the end of the beam range. The proton beam range, however, is highly sensitive to range uncertainty, which makes accurately locating the proton range in the patient difficult. In-vivo range verification is a method to manage range uncertainty, one of the promising techniques being prompt gamma imaging (PGI). In earlier studies, we proposed gamma electron vertex imaging (GEVI), and constructed a proof-of-principle system. The system successfully demonstrated the GEVI imaging principle for therapeutic proton pencil beams without scanning, but showed some limitations under clinical conditions, particularly for pencil beam scanning proton therapy. In the present study, we upgraded the GEVI system in several aspects and tested the performance improvements such as for range-shift verification in the context of line scanning proton treatment. Specifically, the system showed better performance in obtaining accurate prompt gamma (PG) distributions in the clinical environment. Furthermore, high shift-detection sensitivity and accuracy were shown under various range-shift conditions using line scanning proton beams.

• Korean Journal of Microbiology
• /
• v.27 no.3
• /
• pp.291-296
• /
• 1989

Campylobacter jejuni was studied for its disinfection by heat-and cold-treatment and UV-irradiation. When C. jejuni was treated by heat, no viable cell was found after 10 min treatment at $55^{\circ}C$, whereas small fraction of cell population was survived after 60 min treatment at $45^{\circ}C$ and $50^{\circ}C$. When they were treated by cold temperature for 30 days, no cell was survived at -$23^{\circ}C$ but about 4 log of the cells were survived at both temperature of $4^{\circ}C$ and -$40^{\circ}C$. When the organisms were UV-irradiated, thier survival rates were proportionally varied to the distance of irradiation. The scanning electron microscopic studies of C. jejuni cells treated by the disinfecting agents revealed that shapes of thecells were deformed from spiral rod into spherical form. The heat-treated cells showed rough and damaged surface on the scanning electron micrographs. In the heat-treated cells, some proteins of high molecular weight appeared to become accumulated in the electrophoretic analysis. The DNAs extracted from the cells treated with the physical agents showed some differences in agarose gel electrophoresis, comparing those of normal cells.

• Journal of Korean Society on Water Environment
• /
• v.22 no.1
• /
• pp.66-73
• /
• 2006

The purpose of this study was done to evaluate degradation characteristics of non-biodegradable organic matters including aromatic compounds in livestock wastewater using CFZ process. The CFZ process is consisted of coagulation/sedimentation, Fenton oxidation and zeolite adsoption process. degradation charateristics of each treatment water including livestock wastewater were analyzed by UV scanning, FT-IR and GC/MS. After coagulation/sedimentation process as 1st treatment, non-biodegradable matters remained after 1st treatment were removed by using OH radical produced in Fenton oxidation process. As a result of treatment using these processes, NBDCOD removal efficiency was over 90%. Increase of $E_2/E_3$ ratio (absorbance at 250 and 365 nm) in each treatment water means that aromaticity of livestock wastewater decreased. In case of GC/MS, most aromatics or polynuclear aromatics like benzene, phenol and scatol in livestock wastewater almost wasn't detected after oxidation using OH radical.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.6
• /
• pp.53-61
• /
• 2012

The purpose of this study is to understand the mechanism of cementation of soil induced by bacteria. In order to understand the mechanism of cementation of soft soils treated with bacteria, six types of specimens(Not treated, Normal concentration bacteria treatment, High concentration bacteria treatment, Supernatant high concentration bacteria treatment, Double high concentration bacteria treatment, and 25% Specimen high concentration bacteria treatment) were made. Scanning Electron Microscope (SEM), EDX and X-ray diffraction (XRD) analyses were performed on the soft silt and loose sand specimens. Compared with the normal bacteria concentration treated specimen, a clearer cementation between particles was observed in the 25% specimen high bacteria concentration treated specimen. On the basis of the preliminary results, it appears that microbial cementation can occur in the soft soil.

• The Journal of Advanced Prosthodontics
• /
• v.16 no.1
• /
• pp.25-37
• /
• 2024

PURPOSE. To investigate the effect of sintering programs and surface treatments on surface properties, phase transformation and flexural strength of monolithic zirconia. MATERIALS AND METHODS. Zirconia specimens were sintered using three distinct sintering programs [classic (C), speed (S), and superspeed (SS)] (n = 56, each). One sample from each group underwent scanning electron microscopy (SEM) and grain size analysis following sintering. Remaining samples were divided into five subgroups (n = 11) based on the surface treatments: control (CL), polish (P), glaze (G), grind + polish (GP), and grind + glaze (GG). One sample from each subgroup underwent SEM analysis. Remaining samples were thermally aged. Monoclinic phase volume, surface roughness, and three-point flexural strength were measured. Monoclinic phase volume and surface roughness were analyzed by Kruskal-Wallis and Dunn tests. Flexural strength was analyzed by two-way ANOVA and Weibull analysis. The relationships among the groups were analyzed using Spearman's correlation analysis. RESULTS. Sintering program, surface treatment, and sintering × surface treatment (P ≤ .010) affected the monoclinic phase volume, whereas the type of surface treatment and sintering × surface treatment affected the surface roughness (P < .001). Type of sintering program or surface treatment did not affect the flexural strength. Weibull analysis revealed no significant differences between the m and σ_o values. Monoclinic phase volume was positively correlated with surface roughness in the SGG and SSP groups. CONCLUSION. After sintering monolithic zirconia in each of the three sintering programs, each of the surface treatments can be used. However, for surface quality and aging resistance, G or GG can be recommended as a surface finishing method.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.2
• /
• pp.40-44
• /
• 2000

A microscopic study was carried out to get the fundamental informations for the ozone deinking technology. The differential interference microscopic observation showed that ozone treatment was helpful to detach the toner ink from the surface of pulp fiber. The modifications of fiber surfaces by ozone treatment were observed with scanning electron microscope. Modification of fiber surfaces was not severe at the early stage of ozone treatment, but it increased with ozone treatment time and pulp consistency, Therefore, it would be possible to improve the properties of deinked pulp by controlling the condtion of ozone treatment.

• The Journal of Advanced Prosthodontics
• /
• v.11 no.1
• /
• pp.65-74
• /
• 2019

PURPOSE. To evaluate and compare the effect of different materials and techniques on the shear bond strength of veneering ceramic materials to zirconia. MATERIALS AND METHODS. 136 sintered zirconia cubes were prepared and randomly divided into four study groups according to corresponding methods of surface treatment and materials: GLN (grinding followed by laser scanning using Noritake Cerabien ZR), SLN (sandblasting followed by laser scanning using Noritake Cerabien ZR), GLV (grinding followed by laser scanning using VITA VM 9), and SLV (sandblasting followed by laser scanning using VITA VM 9). Spraying technique was performed to coat the core. Profilometer, SEM, XRD, EDS, universal testing machine, and stereomicroscope were used to record surface roughness Ra, surface morphology, phase transformation, elemental compositions, shear bond strength SBS values, and failure types, respectively. Specimens were investigated in unaged (not immersed in artificial saliva) and aged (stored in artificial saliva for a month) conditions to evaluate SBS values. RESULTS. Grinding and GLN as first and second surface treatments provided satisfactory Ra values in both conditions ($1.05{\pm}0.24{\mu}m$, $1.30{\pm}0.21{\mu}m$) compared to sandblasting and other groups (P<.05). The group GLN showed the highest SBS values in both conditions ($30.97{\pm}3.12MPa$, $29.09{\pm}4.17MPa$), while group SLV recorded the lowest ($23.96{\pm}3.60MPa$, $22.95{\pm}3.68Mpa$) (P<.05). Sandblasting showed phase transformation from t-m. Mixed failure type was the commonest among all groups. CONCLUSION. GLN showed to be a reliable method which provided satisfactory bond strength between the veneer ceramic and zirconia. This method might preserve the integrity of fixed dental crowns.