• 한국지반공학회논문집
• /
• 제27권3호
• /
• pp.85-94
• /
• 2011

다양한 모래부피비($sf=V_{sand}/V_{total}$)를 가지는 시료를 조성하여 변형률 크기에 따른 모래-고무 혼합재($D_{sand}/D_{rubber}=1$)의 거동을 분석하였다. 공진주시험, 압밀시험, 그리고 직접전단시험을 실시하였다. 변형률 크기에 따라 모래와 고무는 혼합재 전체 거동을 서로 다르게 제어한다. $sf{\geq}0.4$의 혼합재는 비선형 전단강성의 감소가 관찰되는 반면, $sf{\leq}0.2$의 낮은 모래부피비를 가지는 혼합재는 상당히 높은 탄성한계변형률을 보인다. 고무 입자가 force chain의 역할을 수행할 때 수직변형은 급격한 증가를 보인다. 혼합재 내의 고무부피비가 감소함에 따라 혼합재의 강도는 증가하는 경향을 보이며 $sf{\leq}0.8$의 혼합재는 전단변형에 따라 부피 수축 거동을 보인다. 고무 입자는 변형률 크기에 따라 혼합재 내에서 서로 다른 역할을 수행한다: 미소변형률 영역에서는 혼합재 내의 접촉수 증가 및 소성의 제어; 중간변형률 영역에서는 force chain의 좌굴 방지; 그리고 대변형률 영역에서는 혼합재의 부피수축 거동을 이끈다.

• Geomechanics and Engineering
• /
• 제32권4호
• /
• pp.361-373
• /
• 2023

This study aimed to investigate the engineering properties and mechanical behaviors of polymer-fibers treated sand. Para rubber (PR), natural fiber (NF), and geosynthetic fiber (GF) were used to reinforce poorly graded sand. A series of unconfined compressive and splitting tensile strength tests were performed to analyze the engineering behaviors and strength enhancement mechanism. The experiment results indicated that the PR-fibers mixture could firmly enhance the strength properties of sand. The stress-strain characteristics and failure patterns have been changed due to the increase of PR and fibers content. The presence of PR and fibers strengthened the sand and enhanced the stiffness and ductility behavior of the mixture. The stiffness of reinforced sand reaches an optimum state when both NF and GF are 0.5%, while the optimum PR contents are 20% and 22.5% for the mixture with NF and GF, respectively. An addition of PR and fiber into sand contributed to increasing interlocking zone and bonding of PR-sand interfacial.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.90-96
• /
• 2008

Engineered mixtures composed of rigid sand particles and soft rubber particles are tested to investigate their behavior with strain level. Mixtures are prepared with different volumetric sand fractions (sf) to identify response using small strain resonant column, intermediate strain oedometer, and large strain direct shear tests. The small strain shear modulus and damping ratio are determined with volumetric sand fractions. The asymmetric frequency response curve increases with decreasing sand fraction. Linear responses of shear strain and damping ratio with shear strain are observed at the mixture of sf=0.2. Vertical strain increases with decreasing sand fraction. Mixtures with $04.{\leq}sf{\leq}0.6$ show the transitional stress-deformation behavior from rubber-like to sand-like behavior. The friction angle increases with the sand fraction and no apparent peak strength is observed in mixture without sf=1.0.

• 한국환경복원기술학회지
• /
• 제15권4호
• /
• pp.97-109
• /
• 2012

In this study this writer carried out survey and analysis on paving materials of children's playground for 40 apartment buildings with each of such apartment containing 100 households or more and which were built within last 15 years in Jeonju. As a result of analysis of such questionnaires this author could draw following conclusion. In the second half of 1990s pavement materials which were used mainly were sand and during first half of 2000s they were mixture of sand and rubber block and around 2010 they were rubber block or rubber chip pavements. Such change seemed to be a result of consideration of convenience for management and safety rather than in deference to diversity of children's outing places. Survey on the current status of pavement materials revealed need for directives by the main entity for management and their firm resolve for its implementation. And there was need for their coping with problems such as pressure of treading or lack of it or poor condition of drainage in case of sand and phenomena of pitting or dipping down, discoloring and poor drainage in case of rubber chips and rubber blocks and loosening of gaps between rubber blocks etc. Result of analysing status of usage disclosed that 50.4% of the respondents to questionnaires stated that they had experience of accidents. With regard to cause of such accident it was found that 47.5% of accidents were attributable to play facilities and 19.5% were due to paving (floor) materials thus it was disclosed that not only play facilities but also pavement materials had impact on safety for the children. Result of analysing level of satisfaction with pavement materials showed that pavement by rubber chips and blocks had higher level of satisfaction which was reflection of fear on cleanness of sand. In terms of preference rubber chip and rubber block pavements were highest and the next one was sand. Reason for such preference was based on concern with safety.

• Earthquakes and Structures
• /
• 제27권2호
• /
• pp.127-142
• /
• 2024

The amount of wave propagation through a rubber concrete construction is the subject of the current investigation. Rubber tire waste was used to make two different types of cement mixtures. One type contains sand substitute in amounts ranging from 15% to 60% of the total volume, while the other has gravel with diameters of 3/8 and 8/15 and 15% sand in the same mixture. A wide variety of concrete forms and compositions were created, and their viscous and solid state characteristics were assessed, along with their short-, medium-, and long-term strengths. Diffusion, density, mechanical strength resistance to compressive force, and ultrasound wave propagation were also assessed. The water-to-cement ratio and plasticizer were used in this investigation. In the second part of the study, an analytical model is presented that simulates the experimental model in predicting the speed of waves and the frequencies accompanying them for this type of mixture. Higher order shear deformation beam theory for wave propagation in the rubberized concrete beam is developed, considering the bidirectional distribution, which is primarily expressed by the density, the Poisson coefficient, and Young's modulus. Hamilton's concept is used to determine the governing equations of the wave propagation in the rubberized concrete beam structure. When the analytical and experimental results for rubber concrete beams were compared, the outcomes were very comparable. The addition of rubber gravel and sandy rubber to the mixture both resulted in a discernible drop in velocities and frequencies, according to the data.

• 한국농공학회논문집
• /
• 제61권3호
• /
• pp.31-41
• /
• 2019

More than 90% of roadway in the world are paved as asphalt concrete pavement due to its excellent properties compared with other paving materials; excellent riding quality, flexibility, anti-icing property and easy maintenance-ability. In this study, to make best use of the softer property of the asphalt mixture, the flexible sand asphalt mixture (FSAM) was developed for pedestrian ways. The mix design was conducted to prepare FSAM using PG64-22 asphalt, screenings (sand) less than 5mm, crumb rubber, hydrated lime and limestone powder without coarse aggregate. The deformation strength ($S_D$), indirect tensile strength (ITS) and tensile strength ratio (TSR) tests were conducted to make sure durability of FSAM performance. The impact energy absorption and flexibility were measured by drop-boll test and the resilient modulus ($M_R$) test. The impact energy absorption of FSAM was compared with normal asphalt pavement, concrete pavement, stone and concrete block for pedestrian way. As a result of drop-boll test, FSAM showed higher impact energy absorption compared with other paving materials with the range of 18% to 43%. Impact energy absorption of FSAM increased with increasing test temperature from 5 to $40^{\circ}C$. The results of $M_R$ test at $5^{\circ}C$ showed that the flexibility of FSPA was increased further, because the $M_R$ value of the sand asphalt was measured to be 38% lower than normal dense-graded asphalt mixture (WC-1). Therefore, it was concluded that the FSAM could provide a high impact absorbing characteristics, which would improve walking quality of the pedestrian ways.

• Computers and Concrete
• /
• 제10권2호
• /
• pp.95-104
• /
• 2012

This study uses recycled green building materials based on a Taiwan-made recycled mineral admixture (including fly ash, slag, glass sand and rubber powder) as replacements for fine aggregates in concrete and tests the properties of the resulting mixtures. Fine aggregate contents of 5% and 10% were replaced by waste LCD glass sand and waste tire rubber powder, respectively. According to ACI concrete-mixture design, the above materials were mixed into lightweight aggregate concrete at a constant water-to-binder ratio (W/B = 0.4). Hardening (mechanical), non-destructive and durability tests were then performed at curing ages of 7, 28, 56 and 91 days and the engineering properties were studied. The results of these experiments showed that, although they vary with the type of recycling green building material added, the slumps of these admixtures meet design requirements. Lightweight aggregate yields better hardened properties than normal-weight concrete, indicating that green building materials can be successfully applied in lightweight aggregate concrete, enabling an increase in the use of green building materials, the improved utilization of waste resources, and environmental protection. In addition to representing an important part of a "sustainable cycle of development", green building materials represent a beneficial reutilization of waste resources.

• Geomechanics and Engineering
• /
• 제9권4호
• /
• pp.447-464
• /
• 2015

Millions of scrap tires are discarded annually in Turkey. The bulk of which are currently landfilled or stockpiled. These tires consume valuable landfill space or if improperly disposed, create a fire hazard and provide a prolific breeding ground for rats and mosquitoes. Used tires pose both a serious public and environmental health problem which means that economically feasible alternatives for scrap tire disposal must be found. Some of the current uses of scrap tires are tire-derived fuel, creating barrier reefs and as an asphalt additive in the form of crumb rubber. However, there is a much need for the development of additional uses for scrap tires. One development the creation of shreds from scrap tires that are coarse grained, free draining and have a low compacted density thus offering significant advantages for use as lightweight subgrade fill and backfill material. This paper reports a comprehensive laboratory study that was performed to evaluate the use of a shredded tire-sand mixture as a backfill material in trench conditions. A steel frame test tank with glass walls was created to replicate a classical trench section in field conditions. The results of the test demonstrated that shredded tires mixed with sand have a definite potential to be effectively used as backfill material for buried pipe installations.

• Advances in concrete construction
• /
• 제10권6호
• /
• pp.537-546
• /
• 2020

Exterior walls in buildings are exposed to various forms of thermal loads, which depend on the positions of walls. Therefore, one of the efficient methods for improving the energy competence of buildings is improving the thermal properties of insulation plaster mortar. In this study, lightweight fine aggregate (LWFA) and micro rubber ash (MRA) from recycled tires were used as partial replacements for sand. The flow ability, unit weight, compressive strength, tensile strength, thermal conductivity (K-value), drying shrinkage and microstructure scan of lightweight rubberized mortar (LWRM) were investigated. Ten mixtures of LWRM were prepared as follows: traditional cement mortar (control mixture); three mixes with different percentages of LWFA (25%, 50% and 75%); three mixes with different percentages of MRA (2.5%, 5% and 7.5%); and three mixes consisting both types with determined ratios (25% LWFA+5% MRA, 50% LWFA+5% MRA and 75% LWFA+5% MRA). The flow ability of the mortars was 22±2 cm, and LWRM contained LWFA and MRA. The compressive and tensile strength decreased by approximately 64% and 57%, respectively, when 75% LWFA was used compared with those when the control mix was used. The compressive and tensile strength decreased when 5% MRA was used. By contrast, mixes with determined ratios of LWFA and MRA affected reduced unit weight, K-value and dry shrinkage.

• 한국지반공학회논문집
• /
• 제24권8호
• /
• pp.125-135
• /
• 2008

모래 입자와 연약한 고무 입자로 이루어진 강-연성 혼합재의 응력-변형 및 전단파 특성을 평가하기 위해 고무와 모래의 부피비(sf)와 입자 크기비(sr)를 달리하는 시료를 조성하였다. 벤더 엘리먼트가 설치된 압밀셀을 이용하여 응력-변형시험 및 $K_o$ 상태에서의 미소변형 전단파 시험을 실시하였다. 일정한 입자 크기비를 가지는 강-연성 혼합재는 강성의 입자에서 연성의 입자로 거동이 전이되는 응력-변형 및 미소변형 전단파 특성을 보였다. 또한, $G_{max}=\;{\Lambda}({\sigma}'_{o}/kPa)^{\zeta}$ 관계에서 모래의 부피비(sf)가 $0.4{\sim}0.6$인 구간에서 $\Lambda$계수가 급격히 증가하며 $\zeta$ 지수는 최대값을 보이는 것으로 관찰되었다. 전이 혼합재는 구속응력의 변화에 매우 민감한 거동을 보이며 연성인 고무입자는 재하 하중에 의해 쉽게 변형되므로 최소 간극율을 가지는 강-연성 혼합재의 부피비는 재하된 응력의 크기에 좌우된다. 실내시험을 이용한 본 연구에서는 입자 크기 비와 모래 부피비가 강성 입자와 연성 입자의 혼합재료 거동을 결정하는 것으로 요인으로 분석되었다.