• The Korean Journal of Petroleum Geology
• /
• v.11 no.1 s.12
• /
• pp.18-26
• /
• 2005

An occurrence of inclined heterolithic stratification (IHS) is described from a tidal point bar in a 40-m-deep distributary of the macrotidai, Han River delta, Korea. The channel bank demonstrates a convex-upward profile with intermittent presence or wave-formed scarps and terraces near the low-water level. The vertical succession of IHS is approximately 25 m thick and dips into the channel with angles reaching up to $14^{\circ}C$. The IHS overlies 15 m of trough cross-bedded sand deposited in the channel bottom. Even though the channel as a whole is ebb dominated, the preserved cross bedding is predominantly flood directed because the mutually evasive nature of the ebb and flood currents causes the point bar surface to be flood dominated. The IHS itself consists of inter-stratified fine sand, sandy silt, and silt with an fining-upward textural trend. Seasonal discharge variations of the Han River are not obvious in the deposits, because tile large size, distal location, and energetic tidal environment of the studied channel reduces the impart of river-stage fluctuations.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.3
• /
• pp.135-143
• /
• 2016

We investigated the effectiveness of natural zeolite (NZ) and sand (SD) as a capping material to block the release of heavy metals (Cd, Cr, Cu, and Zn) from heavily contaminated marine sediments and stabilize these heavy metals in the sediments. The efficiency of NZ and SD for blocking trace metals was evaluated in a flat flow tank attached with an impeller to generate wave. 0, 10, 30, and 50 mm depth of NZ or SD were capped on the contaminated marine sediments and the metal concentration in seawater was monitored. After completion of flow tank experiments, sequential extractions of the metals in the sediment below the capping material were performed. The difference of pH, EC, and DO concentration between uncapped and capped condition was not significant. The release of cations including Cd, Cu, and Zn were effectively blocked by NZ and SD capping but the interruption of Cr release was observed only in 50 mm depth of SD capped condition. However, the stabilization of Cr in 50 mm depth of SD capped condition was not achieved when compared to uncapped condition. NZ and SD capping were effective for stabilizing Cd, Cu, and Zn in marine sediments. It is concluded that the use of NZ with SD as a capping material is recommended for blocking Cd, Cr, Cu, and Zn release and stabilizing them in contaminated marine sediments.

• The Journal of Engineering Geology
• /
• v.13 no.4
• /
• pp.405-418
• /
• 2003

Measurements of volumetric water content and saturation of porous media are very important factors in understanding the physical characteristics of soil, groundwater recharge by rainfall, pollutant movement, and slope failure. To measure such physical parameters, a permittivity method using electromagnetic wave is applied and use is made of the special permittivity response of understand to water and ethanol. In particular, the estimation is required because permittivity is influenced by the nature of the underground environment. In this study, we carried out experiments on the relative dependency of soil density, temperature and salinity of standard sand and granitic weathered soil using FDR-V system (Frequency domain reflectometry with vector network analyzer) within a frequency range of 1 - 18 GHz. The results of the study showed that the dielectric constants of standard sand and granitic weathered soil increased with increased volumetric water content of soil. However, the dependency of soil density was found to be a little low. Changes of dielectric constant with temperature appeared definitely in the real part of 1 GHz. That is, the dielectric constant of real part at 1 GHz of water and standard sand increased with the rise of temperature. However, ethanol showed decreased tendency. The study also showed that dielectric constant increased with increase in salinity at imaginary part of 1 GHz. It could be concluded from this study FDR-V system can adequately measure the physical properties of soil and the degree of salinity concentration of porous media within 1 GHz frequency range using dielectric constant.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2000.05a
• /
• pp.37-40
• /
• 2000

Acoustically enhanced soil flushing method is a newly developed in-situ remediation technique. However, there has not been an analytical method that can be used to evaluate the effectiveness of ultrasonic wave under different conditions. This study was undertaken to investigate the degree of enhancement in contaminant removal due to ultrasonic energy on the soil flushing method. The test conditions included different levels of ultrasonic power and hydraulic gradient. The test soils were Ottawa sand, a fine aggregate, and a natural soil, and the surrogate contaminant was a Crisco Vegetable Oil. The test results showed that sonication could increase contaminant removal significantly. Increasing sonication power increased pollutant removal. The faster the flow is, the smaller the degree of enhancement will be. The pollutants in dense soils are more difficult to be removed than in loose soils.

• Computers and Concrete
• /
• v.20 no.3
• /
• pp.311-318
• /
• 2017

This paper investigates the utilization of waste tyre crumb rubber as the fine aggregate in precast concrete Paving block (PCPB). PCPB's are generally preferred for city roads, pedestrian crosswalk, parking lots and bus terminals. The main aim of this paper is to evaluate the mechanical properties of wet cast PCPB containing waste tyre crumb rubber. The mechanical properties were investigated using a density, compressive strength, split tensile strength and flexural strength tests at 7, 28 56 days according to the IS 15688:2006 and EN1338. The wet cast method was followed for producing PCPB samples. The fine aggregate (river sand) was replaced with waste tyre crumb in percentage of 5%, 10%, 15%, 20% and 25% by volume. All the test results were compared with the conventional PCPB (Without rubber). The test results indicate its feasibility for incorporating waste tyre crumb rubber in the production of PCPB by the wet cast method.

• The Korean Journal of Malacology
• /
• v.24 no.2
• /
• pp.81-87
• /
• 2008

Distribution, population structure, and growth of the bivalve Protothaca euglypta were investigated for clams collected from the northwestern part of the East Sea of Russia. This species is distributed in further northern area than it was found earlier. In the southern area, this clam is found in the intertidal zone, up to 8 m in depth. It is one of the most numerous infaunal species of bivalves, and protected to wave action in the gravel-pebble and sand with rubble biotope. Population density of P. euglypta reaches 500 $spc./m^2$, and biomass 2 $kg/m^2$. Size and age composition of the local settlements and allometric growth of P. euglypta depend on a biotope. The growth rate of P. euglypta considerably reduces in case of the northern boundary area, whereas life span increases.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.477-484
• /
• 2001

In this paper shows the evaluation of the liquefaction potential of soils using in situ test. There are different types of in situ test used in the evaluation the liquefaction potential. In the particular study the Standard penetration test(SPT), Cone penetration test(CPT), ad Seismic cone penetration test (SCPT) were used. The SPT N value has been used all over for a very long time. The evaluation of the liquefaction of soil was preformed using the worldwide renowned CPT and SCPT. Shake 91 program was used to evaluate the results obtained by different in situ test and were later analyzed.

• Journal of Industrial Technology
• /
• v.32 no.A
• /
• pp.79-86
• /
• 2012

In this paper, centrifuge model tests and numerical analysis on the breakwater structure were performed to investigate the stability and behavior of breakwater in field. In centrifuge model tests, construction sequence of breakwater structure such as preparation of weathered rock and sand deposit, construction of D.C.M, rubble mound with crushed stones and installment of breakwater structure was reconstructed like field condition and the behavior of ground settlement and breakwater displacement during stage of construction was observed during tests. For the final stage of simulating the horizontal movement of breakwater due to wave force, horizontal load was applied by horizontal loading apparatus being specially designed so that horizontal displacement of structure could be observed. Numerical analysis were also carried out and its results were compared with test results to assess the property of centrifuge model tests with respect to the behavior of structure as well as ground.

• Journal of Ocean Engineering and Technology
• /
• v.20 no.2 s.69
• /
• pp.29-35
• /
• 2006

The flow patterns around multi-circular cylinders are studies, in order to obtain a global view on the structure of wave control and circulation of sea flow in coastal region. The flow force depends upon the vortex shedding exerted on the structure, especially how the vortex shedding affects the erosion when the structure sets on the sand bottom. Therefore, it is necessary that the flow pattern be hocked. In order to simulate the flow around multi-circular cylinders, the CFX and FLUENT of the computational fluid dynamics (CFD) program were used and compared with the experimental results of the flow visualization installation. The phenomena of flow around the multi-cylinders will be applied to fundamental data for predicting the flow force acting against the structure, erosion and sedimentation around cylinders in arrangement.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1278-1284
• /
• 2008

This study carried out bender element tests in a calibration chamber in order to estimate the characteristics of soil specimen prepared in a calibration chamber. Basically, the purpose of bender element test is to measure the shear wave velocity. Bender element test cannot only confirm the status of soil specimen deposited in a chamber, but also estimate the consolidation process indirectly. In order to carry out bender element test in a calibration chamber, a pair of bender elements was installed inside the chamber, using the 'ㄷ' shaped frame. For the sandy soils having various relative densities in various stress conditions, the maximum shear modulus was estimated. From the comparison with bender element test results in a triaxial testing device, testing device and procedure was validated.