• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.3
• /
• pp.101-108
• /
• 2016

Each year, more than seven hundred thousand tons of copper slag are generated in Korea as a byproduct during the production of copper. Due to the large amount of copper slag produced, there has been increased interest in the use of copper slag as a construction material. To evaluate the potential of copper slag as a construction material, laboratory evaluations were conducted in this study, and three particle shapes and replacement rates of river sand were selected as experimental variables. Strength, air-void characteristics, and sulfuric acid resistance were the three properties evaluated to assess whether copper slag can be used as a construction material. Test results indicate that the gradation of copper slag has an effect on strength, and the maximum strength was achieved when 60 % of river sand was replaced with copper slag. In addition, when compared with ordinary Portland cement mortar, replacing river sand with copper slag reduced air void size and increased sulfuric acid resistance.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.37 no.4
• /
• pp.693-703
• /
• 2017

Rover wheel's mobility depends on soil's condition and wheel's design. The purpose of this study is to evaluate the effect of soil conditions, which are Jumunjin sand and Korean lunar soil simulant (KLS-1), on wheel's motion performance. The experiments were performed by using a single wheel testbed with a wheel which grouser height is 15mm on Jumunjin sand and KLS-1, respectively. Also the influence of grouser length to wheel's mobility performance was studied. The experimental results of torque, drawbar pull and sinkage relating to slip ratio were discussed and analyzed to evaluate wheel's motion performance. Results showed wheel moving on KLS-1 has high performance than Jumunjin sand. Wheel's mobility performance was influenced by soil's properties of cohesion and frictional angle. In addition, wheel's performance of drawbar pull and Torque increased with the increasing of grouser length.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.11
• /
• pp.27-37
• /
• 2011

A series of centrifuge model tests to investigate the suction pile pullout loading capacity in sand have been performed. The main parameters that affect the pullout loading capacity of a suction pile include the mooring line inclination angle and the padeye position of the suction pile. With respect to the padeye position, the maximum pullout loading capacity is obtained when the padeye position is near 75% of the pile length from the top. The direction of the pile rotation changes when the padeye position reaches somewhere near 50~75% for all mooring line inclination angles. The translation displacement of suction pile to develop the time of maximum pullout loading capacity decreased as the mooring line inclination angle increased. In addition, the vertical displacements of the center of a suction piles for all cases appeared to develop toward the ground surface.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.9
• /
• pp.21-32
• /
• 2020

In this study, series of cyclic triaxial tests and shear velocity measurement were conducted using Pohang sand, which was taken from liquefaction observed area, to verify the liquefaction characteristics of Pohang. The cyclic resistance ratio(CRR) was derived based on the test results. A specimen was reconstituted into 40% and 80% relative density conditions and then a series of cyclic triaxial tests and shear-wave velocity measurement were conducted. As a result, the effect of particle distribution and relative density to liquefaction resistance was verified. The liquefaction resistance of Pohang sand was evaluated by comparing with other liquefaction resistance of sands from previous research. In addition, the liquefaction resistance curve from field observation data was used to verify the reliability of results from this study by measured shear-wave velocity.

• Journal of The Geomorphological Association of Korea
• /
• v.25 no.4
• /
• pp.37-47
• /
• 2018

Coastal sand dunes have been regarded as natural defenses to protect hinterland from disasters such as storm surge and typhoons. However, many dunes are not well-deserved in South Korea because of imprudent land development or inappropriate measures after coastal erosion. Lately, beach nourishment and dune reinforcement are emphasized as the effective and environmentally sustainable solution for the coastal protection. They are regarded good strategies to keep landscapes for a time, with little side effects. However, there is little knowledge on the construction methods including proper design and time plans for the best results.In addition, the effects of dune reinforcement in the field should be tested.In thisstudy, we performed sand filling in an eroded dune scarp and surveyed topographic changes in the beach-dune system, which is located along Dasa-ri coast, Chungnam Province, South Korea. Using a network RTK-GPS and drone-based aerial photographs, we analyzed the temporal and spatial changes in the area, before and after the reinforcement. As a result, the dune reinforcement seems to be helpful to mitigates the coastal erosion and to prevent the coastline retreat at least for one year.

• Nuclear Engineering and Technology
• /
• v.54 no.8
• /
• pp.3051-3058
• /
• 2022

In the present work, untreated Iraqi sand with grain sizes varied between 100 and 200 ㎛ was used to produce a colored glass sample that has shielding features against the low gamma-ray energy. Therefore, a weight of 70-60 wt % sand was mixed with 9-14 wt% B₂O₃, 8-10 wt% Na₂O, 4-6 wt% of CaO, 3-6 wt% Al₂O₃, in addition to 0.3% of Co₂O₃. After melting and annealing the glass sample, the X-ray diffraction spectrometry was applied to affirm the amorphous phase of the fabricated glass samples. Moreover, the X-ray dispersive energy spectrometry was used to measure the chemical composition, and the MH-300A densimeter was applied to measure the fabricated sample's density. The Makishima-Makinzie model was applied to predict the mechanical properties of the fabricated glass. Besides, the Monte Carlo simulation was used to estimate the fabricated glass sample's radiation shielding capacity in the low-energy region between 22.1 and 160.6 keV. Therefore, the simulated linear attenuation coefficient changed between 10.725 and 0.484 cm^-1, raising the gamma-ray energy between 22.1 and 160.6 keV. Also, other shielding parameters such as a half-value layer, pure lead equivalent thickness, and buildup factors were calculated.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.2
• /
• pp.29-39
• /
• 2006

In the companion paper (Paik 2006), a new formulation for calculating the nonlinearly distributed active earth pressure acting on a caisson backfilled with crushed rock and sand is proposed, and it takes into account arching effects as well as difference in internal friction angles and unit weights between sand and crushed rock. In this study, in order to partially check the accuracy of the proposed equation, the results of the proposed equation are compared with the equation proposed by Paik (2003a) for caissons with rough surface and homogeneous backfill, and are compared with results of Rankine's theory for caissons with smooth surface and homogeneous backfill. In addition, a parametric study is performed to investigate the effect of $phi_{r}$, $phi_{s}$, $\delta_{r}$, $\gamma_{r}$, $\gamma_{s}$ and $\beta$ on the magnitude of active earth pressure acting on the caisson, and construction methods for minimizing active earth pressure on the caisson are also provided based on the results of a parametric study.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.6C
• /
• pp.377-384
• /
• 2006

Theoretical and experimental study of the unconfined penetration (UP) test was conducted to suggest a new test method (referred to as IUP, Improved Unconfined Penetration) for determination of the tensile strength of compacted sand-bentonite mixtures. The tensile strength of compacted mixtures can be calculated from limit analysis based on the theory of perfect plasticity. The measurement errors in new test method were reduced by improving the UP device. Preliminary experiment results indicate that the tensile strength increases with increasing the disk size, loading rate and pH level. In addition, the disk diameter with 25.4 mm and the loading rate with 0.5%/min~1%/min are most suitable condition for the IUP test. The reliability of IPU test was verified by through the fact that good agreement between the IUP and conventional split tensile test results is observed.

• Journal of The Geomorphological Association of Korea
• /
• v.28 no.1
• /
• pp.51-66
• /
• 2021

This study shows that coastal sand dunes are negatively affected by coastal forests. In South Korea, planting pine trees on the dunes has been carried out to stabilize the dune landscapes and protect residential areas from coastal disasters since the 20th century. However, this strategy could reduce the resilience of dunes. In this study, we selected three monitoring sites with automated weather stations to compare the geomorphological and environmental characteristics between tree-covered and grass-covered dunes at Sohwang-ri, Boryeong-si, Chungnam Province for three years. In addition, we monitored the rates of erosion and deposition using eight pins along the dune crests. We found that the forest affected both wind velocity and direction, resulting in decreased blown sand supply to the dunes in front of the forest. The velocity of the strong winds faster than 5 m/s diminished to 10%-30% of the control sites, and the direction of northwesterly wind were skewed to the north by about 6°. Sand deposition occurred at about 15-20 m away from the pine forest and the amount was only 1/10 of the deposition within the grass-covered dunes. This study suggests that planting trees in coastal dunes is an undesirable strategy with negative impacts on the landscape management.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.5 no.1
• /
• pp.19-24
• /
• 2009

Bentonite-based grouting has been usually used for sealing a borehole installed for a closed-loop vertical ground heat exchanger in a geothermal heat pump system (GHP) because of its high swelling potential and low hydraulic conductivity. The bentonite-based grout, however, has relatively lower thermal conductivity than that of ground formation. Accordingly, it is common to add some additives such as silica sand into the bentonite-based grout for enhancing heat transfer. In this study, graphite is adapted to substitute silica sand as an addictive because graphite has very high thermal conductivity. The effect of graphite on the thermal conductivity of bentonite-based grouts has been quantitatively evaluated for seven bentonite grouts from different product sources. In addition, the viscosity of graphite-added bentonite grout was measured to evaluate the field pumpability of the grout.