• Journal of information and communication convergence engineering
• /
• v.2 no.2
• /
• pp.76-79
• /
• 2004

The DS-SS (Direct Sequence Spread Spec1nun) transmitter is part of a low data rate (∼150 kbps - burst rate and 64 bps - average data rate) wireless communication system. It is traditionally implemented using Digital Signal processing chip (DSP). However, with rapid increase in variety of services through cell phones, such as, web access, video transfer, online games etc. demand for higher rate is increasing steadily. Since the chip rate and thereby the sampling rate requirements of the system are fairly high, the transmitter should implemented using Field programmable Gate Arrays FPGAs instead of a DSP. This paper shows the steps taken to get a working prototype of the transmitter unit on a FPGA based platform.

• International Journal of Safety
• /
• v.3 no.1
• /
• pp.27-31
• /
• 2004

Some of the petroleum products contain benzene which is well known as a confirmed human carcinogen. For example, gasoline products contain benzene ranging up to several percents by weight. High exposures to the benzene and other organic solvents would be likely to occur during intermittent tasks and or processes rather than continuous jobs such as sampling, repair, inspection, and loading/unloading jobs. The work time for these jobs is various. However, most of work time is very short and the representative time interval is 15 minutes. Thus, it is preferable to do exposure assessment for 15 minute time weighted average which is known as a short time exposure level(STEL) by ACGIH rather than for 8-hours TWA. It is particularly significant to the exposure monitoring for benzene since it has been known that the exposure rate plays an important role to provoke the leukemia. Due to the large variations, a number of processes/tasks, the traditional sampling technique for organic solvents with the use of the charcoal and sampling pumps is not appropriate. Limited number of samples can be obtained due to the shortage of sampling pumps. Passive samplers can eliminate these limitations. However, low sampling rates resulted in collection of small amount of the target analysts in the passive samplers. This is originated the nature of passive samplers. Field applications were made with use of passive samplers to compare with the charcoal tube methods for 15 minutes. Gasoline loading processes to the tank lorry trucks at the loading stations in the petroleum products storage area. Good agreements between the results of passive samplers and those of the charcoal tubes were achieved. However, it was found that special cautions were necessary during the analysis at very low concentration levels.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.343-345
• /
• 2015

Currently, SAW Device has been used as a frequency filter using the property of passing only a desired frequency with a narrow bandwidth. However, the areas of activity in various fields since the permanent advantages can be widened by using a non-powered. These sensor tags using SAW Device has been done, but a lot of research, the development of the state still insufficient for Reader Platform. How to read the value of the ID Tag Using SAW Device has a time domain sampling (TDS) method and a frequency domain sampling (FDS) method. The purpose of the paper, we use the FDS method that requires high-speed processing with a relatively slow sampling rate does not require high-speed sampling. Reader Platform was the way to detect ID through PC as FDS way, but It is based on the Cortex-A9 processor and it works a low price, compact and real-time Reader Platform.

• Journal of Korean Society for Quality Management
• /
• v.17 no.1
• /
• pp.69-81
• /
• 1989

This study is concerned with a job sequencing method using the concept of sampling technique in the case of Job Shop. This is the follow study of Kang and Ro (1988) which examined the possibility of application of sampling technique to determine the Job Sequence in the case of Flow Shop. Not only it is very difficult, but also it takes too much time to develop the appropriate job schedules that satisfy the complex work conditions. The most job sequencing algorithms have been developed to determine the best or good solution under the special conditions or assumptions. The application areas of these algorithms are also very narrow, so it is very hard to find the appropriate algorithm which satisfy the complex work conditions. In this case it is very desirable to develop a simple job sequencing method which can select the optimal job sequence or near optimal job sequence with a little effort. This study is to examine the effect of sampling job sequencing which can select the good job of 0.01%~5% upper good group. The result shows that there is the sets of 0.05%~23% job sequence group which has the same amount of performance measure with the optimal job sequence in the case of experiment of N/M/G/$F_{max}$. This indicates that the sampling job sequencing method is a useful job sequencing method to find the optimal or good job sequence with consuming a small amount of time. The results of ANOVA show that the only one factor, number of machines is the significant factor for determining the job sequence at ${\alpha}=0.01$. It takes about 10 minutes to compare the number of 10,000 samples of job sequence by personal computer and it is proved that the selection rate of the same job sequence with optimal job sequence is 23.0%, 3.9% and 0.065% in the case of 2 machines, 3 machines and 4 machines, respectively. The area of application can readily be extended to the other work condition.

• Analytical Science and Technology
• /
• v.18 no.4
• /
• pp.338-343
• /
• 2005

In this work, sample loss of reduced sulfur compounds (RSC) was investigated with respect to bag sampling techniques. For comparison purpose, calibration slopes were obtained by analyzing standards prepared by 'within syringe dilution' (WSD) method against those made either by 'Tedlar bag dilution' (TBD) or by 'polyester aluminum bag dilution' (PBD) method. The results indicated that the recovery rate of TBD showed the mean values of about 87%, while those of PBD about 77%. Despite the fact that sample loss is inevitable, precise sampling of reduced sulfur compounds may still be possible, if one acknowledges and be prepared for such loss rates of bag sampling methods.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.12 s.354
• /
• pp.61-67
• /
• 2006

This paper proposes the algorithm for tracking of the residual phase errors incurred by carrier frequency offset and sampling frequency offset in the orthogonal frequency division multiplexing (OFDM) systems which are suitable for high data rate wireless communications. In the OFDM systems the subcarriers which are orthogonal to each other are modulated by digital data and transmitted simultaneously. The carrier frequency offset causes degradation of signal to noise ratio(SNR) performance and interference between the adjacent subcarriers. The errors in the sampling timing caused by the sampling frequency difference between the transmitter and the receiver sides also cause a major performance degradation in the OFDM systems. The residual error tracking and compensation mechanism is essential in the OFDM system since the carrier and the sampling frequency offset cause the loss of orthogonality resulting in the system performance loss. This paper proposes the scheme where the channel gain and the payload data information are reflected in the residual error tracking process which results in the reduction of the estimation error and the tracking performance improvements under the frequency selective fading wireless channels.

• Journal of Korean Society for Quality Management
• /
• v.51 no.4
• /
• pp.515-530
• /
• 2023

Purpose : This research aims to develop a data-driven inspection policy for radio stations utilizing the KS Q ISO 2859-1 sampling method, addressing potential regulatory relaxations and impending management challenges. Methods : Using radio station inspection big data from the past six years, we established a simulation model to evaluate the current policy. A new inspection sampling policy framework was designed based on the KS Q ISO 2859-1 method. The study compares the performance of the current and proposed inspection systems, offering insights for an improved inspection strategy. Results : This study introduced a simulation model for inspection system based on the KS Q ISO 2859-1 sampling method. Through various experimental designs, key performance indicators such as non-detection rate and sample proportion were derived, providing foundational data for the new inspection policy. Conclusion : Using big data from radio station inspections, we evaluated current inspection systems and quantitatively compared a new system across diverse scenarios. Our simulation model effectively verified the feasibility and efficiency of the proposed framework. For practical implementation, essential factors such as lot size, inspection cycle, and AQL standards need precise definition and consideration. Enhancing radio station inspections requires a policy-driven approach that factors in socio-economic impacts and solicits feedback from industry participants. Future study should also explore various perspectives related to legislative, institutional, and operational aspects of inspection organizations.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.174-182
• /
• 2014

To monitor the wind-induced responses of buildings, conventional real-time kinematic (RTK) methods based on two global positioning system (GPS) receivers (e.g., a reference and a rover) are widely applied. However, these methods can encounter problems such as difficulty in securing and maintaining a space for a reference station. With the recently developed virtual reference station (VRS)-RTK approach, the position of a structure can be measured using only a rover receiver. In this study, to evaluate the applicability of VRS-RTK methods in monitoring the lateral structural responses of frame structures, we performed free vibration tests on a one-story frame model (the first natural frequency of 1 Hz) and a three-story frame model (the first natural frequency of 0.85 Hz). To assess the reliability of the displacement and acceleration responses measured by the GPS, we performed a concurrent measurement using laser displacement sensors and an accelerometer. The accelerometer results were consistent with the GPS measurements in terms of the time history and frequency content. Furthermore, to derive an appropriate sampling rate for the continuous monitoring of buildings, the errors in the displacement responses were evaluated at different GPS sampling rates (5, 10, 20 Hz). The results indicate that as the sampling rate increased, the errors in the displacement responses decreased. In addition, in the three-story model, all modal components (first, second, and third modes) could be recorded at a sampling rate of 20 Hz.

• Journal of the Korean Data and Information Science Society
• /
• v.13 no.2
• /
• pp.129-138
• /
• 2002

This paper deals with logistic regression models for analysing separation rates from majors. The model building procedure shows how to incoporate the effects of some factors causing from three-way nested sampling scheme and discusses what type of characteristics as independent variables directly affecting the rates should be considered.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.497-498
• /
• 2009