• ETRI Journal
• /
• v.33 no.3
• /
• pp.326-334
• /
• 2011

This paper outlines the time jitter effect of a sampling clock on a software-defined radio technology-based digital intermediate frequency (IF) transceiver for a mobile communication base station. The implemented digital IF transceiver is reconfigurable to high-speed data packet access (HSDPA) and three bandwidth profiles: 1.75 MHz, 3.5 MHz, and 7 MHz, each incorporating the IEEE 802.16d worldwide interoperability for microwave access (WiMAX) standard. This paper examines the relationship between the signal-to-noise ratio (SNR) characteristics of a digital IF transceiver with an under-sampling scheme and the sampling jitter effect on a multichannel orthogonal frequency-division multiplexing (OFDM) signal. The simulation and experimental results show that the SNR of the OFDM system with narrower band profiles is more susceptible to sampling clock jitter than systems with relatively wider band profiles. Further, for systems with a comparable bandwidth, HSDPA outperforms WiMAX, for example, a 5 dB error vector magnitude improvement at 15 picoseconds time jitter for a bandwidth of WiMAX 3.5 MHz profile.

• International Journal of Automotive Technology
• /
• v.8 no.2
• /
• pp.149-154
• /
• 2007

The engine behavior in a transient condition is important to not only emission regulations but also fuel economy. A fast response gas analyzer can be a useful tool to investigate exhaust gas in a transient operation. It should be designed to analyze gas concentration with a short time constant by a fast sampling module and an appropriate measuring method for each emission element. In this study, a new fast sampling module is introduced and flow analysis is performed by numerical simulation. The analysis has shown the proper operating condition and the sensitivity of the module for practical application. Calculated flow to the sampling module has $0.5{\sim}4%$ error, while backflow toward the expansion tube is expected when pressure in CP (Constant Pressure) chamber is over 0.6 bar. For a stable supply of flow to the optical cell, sample gas pressure should be in the range, $0.35{\sim}1.90$ bar, when the pressure in the CP camber and the optical cell are 0.2 bar and 0.158 bar, respectively.

• Journal of the Korean Statistical Society
• /
• v.13 no.2
• /
• pp.107-113
• /
• 1984

In a linear regression model the idependent variables are frequently subject to measurement errors. For this case, the problem of estimating unknown parameters has been extensively discussed in the literature while very few has been concerned with the effect of measurement errors on prediction. This paper investigates the behavior of the predicted values of the dependent variable in terms of the average mean square error of prediction (AMSEP). AMSEP may be used as a criterion for selecting an appropriate estimation method, for designing an estimation experiment, and for developing cost-effective future sampling schemes.

• Journal of the Korean Statistical Society
• /
• v.29 no.4
• /
• pp.435-441
• /
• 2000

Ko(1998, 1999) proposed certain flexible two-stage plans that could be served as one-step interim analysis in on-going clinical trials. The proposed Plans are optimal simultaneously in both a Bayes and a Neyman-Pearson sense. The Neyman-Pearson interpretation is that average expected sample size is being minimized, subject just to the two overall error rates $\alpha$ and $\beta$, respectively of first and second kind. The Bayes interpretation is that Bayes risk, involving both sampling cost and wrong decision losses, is being minimized. An example of this correspondence are given by using a binomial setting.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.232-237
• /
• 1991

Digital Variable Structure Controller(DVSC) is proposed to control variable speed recirculating pump for hot-water heating control system. In this study, nonlinear sliding line is used beyond output error boundary layer and PID sliding line is used within the layer. For long dead time compensation, constraint is added to Smith predictor algorithm. Steady state error is eliminated by using the proposed sliding line in spite of heating load change. By decreasing sampling time, good sliding motion is yielded but system output noise bv flow dynamics is amplified.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.10 no.2
• /
• pp.128-133
• /
• 2010

This paper presents a method for estimating the parameters of dynamic models for induction motor dominating loads. Using particle swarm optimization, the method finds the adequate set of parameters that best fit the sampling data from the measurement for a period of time, minimizing the error of the outputs, active and reactive power demands and satisfying the steady-state error criterion.

• The Korean Journal of Applied Statistics
• /
• v.25 no.4
• /
• pp.697-706
• /
• 2012

An Agresti-Coull type test is considered for the difference of binomial proportions in two doubly sampled data subject to common false-positive error. The performance of the test is compared with likelihood-based tests. The Agresti-Coull test has many desirable properties in that it can approximate the nominal significance level well, and has comparable power performance with a computational advantage.

• Communications for Statistical Applications and Methods
• /
• v.20 no.5
• /
• pp.357-366
• /
• 2013

This paper defines an improvement for estimating the population mean of a study variable using auxiliary information and known values of certain population parameter(s), when there is a non-response in a study as well as on auxiliary variables. Under a simple random sampling without a replacement (SRSWOR) scheme, the mean square error (MSE) of all proposed estimators are obtained and compared with each other. Numerical illustration is also given.

• Journal of the Korean Data and Information Science Society
• /
• v.24 no.4
• /
• pp.885-893
• /
• 2013

This paper considers Bayes estimations of the small area means under Fay-Herriot model with measurement errors. We provide empirical Bayes predictors of small area means with the corresponding jackknifed mean squared prediction errors. Also we obtain hierarchical Bayes predictors and the corresponding posterior standard deviations using Gibbs sampling. Numerical studies are provided to illustrate our methods and compare their eciencies.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.8 s.251
• /
• pp.923-930
• /
• 2006

A Kriging model is a sort of approximation model and used as a deterministic model of a computationally expensive analysis or simulation. Although it has various advantages, it is difficult to assess the accuracy of the approximated model. It is generally known that a mean square error (MSE) obtained from the kriging model can't calculate statistically exact error bounds contrary to a response surface method, and a cross validation is mainly used. But the cross validation also has many uncertainties. Moreover, the cross validation can't be used when a maximum error is required in the given region. For solving this problem, we first proposed a modified mean square error which can consider relative errors. Using the modified mean square error, we developed the strategy of adding a new sample to the place that the MSE has the maximum when the MSE is used for the assessment of the kriging model. Finally, we offer guidelines for the use of the MSE which is obtained from the kriging model. Four test problems show that the proposed strategy is a proper method which can assess the accuracy of the kriging model. Based on the results of four test problems, a convergence coefficient of 0.01 is recommended for an exact function approximation.