• Journal of Navigation and Port Research
• /
• v.43 no.6
• /
• pp.369-376
• /
• 2019

Ship hydrodynamics in the confined waterways is challenging. When a ship is maneuvering in confined waterways, the hydrodynamic behavior may vary significantly because of the hydrodynamic interaction between the bottom of the ship hull and the seabed, or so-called shallow water effects. Thus, an accurate prediction of shallow water and bank effects is essential to minimizing the risk of the collision and the grounding of the ships. The hydrodynamic derivatives measured by the virtual captive model test provide a path to predicting the change in ship maneuverability. This paper presents a numerical simulation of captive model tests to predict the maneuverability of a ship in confined waterways. Also, straight and zig-zag simulation were conducted to predict the trajectory of a ship maneuvering in confined waterways. The results showed that the asymmetric flow around a ship induced by vicinity of banks causes pressure differences between the port and starboard sides and the trajectory of a ship maneuvering in confined waterways.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.7
• /
• pp.800-806
• /
• 2016

The maneuverability of a tugboat is affected by the slewing motion of a barge while the tug is navigating with the barge in water. Therefore, it is necessary to reduce the slewing motion of the barge to allow for safe towing work. In this study, a water tank experiment was performed to examine the factors affecting the slewing motion of a barge and improve course stability. The characteristics of slewing motion vary according to bow shape. Three barge models, each with a different bow shape, were selected as experimental subjects. A comprehensive analysis was performed to study the effects of various factors on the slewing motion of a barge such as the presence of a skeg and bridle, towing speed, and the length of the towline. The effect of the location of the skeg varied according to bow-hull form. The slewing motion of the barge decreased as the length of the towline increased, and this decrease was even greater when a bridle was connected to the towline. In addition, the slewing motion decreased significantly as the length of the bridle increased. The slewing angles did not show significant change with respect to towing speed.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2018.11a
• /
• pp.12-13
• /
• 2018

For navigation safety, navigators have to be familiar with maneuverabilities. When a vessel encounters a danger of collisions and stranding, maneuverability is essential for the safety of ship. It is composed of turning, course change, speed change, etc. In the latter part, maneuverabilities and motion of Training Ship HANBADA are provided by full-scale measurement in the $10^{\circ}/10^{\circ}$ Zig-Zag Test, $20^{\circ}/20^{\circ}$ Zig-Zag Test and Turning Circle Test(Port and Starboard). It aims to provide information on maneuverabilities and motion of Training Ship HANBADA so that the navigators can take proper action to avoid.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.4
• /
• pp.430-437
• /
• 2018

For a ship navigating in waves, added resistance, sway force and yaw moment due to waves differ from still water conditions, which affects the maneuverability of the ship. Therefore, it is important to estimate the sway force and yaw moment generated by waves. In this study, numerical simulations were carried out to calculate the hydrodynamic forces acting on a barge in still water and waves using CFD. Based on the results, the characteristics of course stability of a barge were investigated and analyzed. The hydrodynamic forces acting on the barge in waves were stronger than in still water, and it was confirmed that hydrodynamic forces become greater as wavelength becomes longer. In long wavelength regions, the (-) value of the yaw damping lever was larger than in still water. However, in short wavelength regions and when wavelength coincided with the length of the ship, values were smaller than in still water. In this region, it can be assumed that course stability improved. In other words, in long wavelength regions, the course stability of the barge was worse than in still water and short wavelength regions. Therefore, attention is required for safe navigation in long wavelength regions.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.5
• /
• pp.595-602
• /
• 2017

In Korea, much research and development have occurred to enhance the technological competitiveness of tuna purse seining fisheries. Due to these efforts, fishing efficiency has been improved with the development of radar, sonar and global positioning systems for fish detection and revisions to the hull forms of tuna purse seiners. However, for skiff boats, net boats and speed boats, which are auxiliary working boats mounted on tuna purse seiners, technology has lagged behind relative to the modernization of the main vessel. In this study, the hull of an existing propeller-based net boat with steel wire net to protect tuna was changed to the hull of a water jet propulsion vehicle to reduce resistance and improve maneuverability. As a result, a prototype of a water jet propulsion option was produced according to the aluminum structure strength standards specified by the Ministry of Oceans and Fisheries, and safety was confirmed by performing a drop test. Moreover, through a sea trial test, an existing net boat was shown to have a speed of 12.0knots and a towing force of 2,545 kgf at 2,500 RPM. The prototype had a speed of 26.7 knots and a towing force of 2,011 kgf at 3,200 RPM, which satisfied the towing capacity standards of auxiliary working boats mounted on tuna purse seiners.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.7
• /
• pp.922-930
• /
• 2020

Marine accidents involving fishing boats, caused by a loss of stability, have been increasing over the last decade. One of the main reasons for these accidents is a sudden wind attacks. In this regard, the wind loads acting on the ship hull need to be estimated accurately for safety assessments of the motion and maneuverability of the ship. Therefore, this study aims to develop a computational model for the inlet boundary condition and to numerically estimate the wind load acting on a fishing boat. In particular, wind loads acting on a fishing boat at the wind speed profile boundary condition were compared with the numerical results obtained under uniform wind speed. The wind loads were estimated at intervals of 15° over the range of 0° to 180°, and i.e., a total of 13 cases. Furthermore, a numerical mesh model was developed based on the results of the mesh dependency test. The numerical analysis was performed using the RANS-based commercial solver STAR-CCM+ (ver. 13.06) with the k-ω turbulent model in the steady state. The wind loads for surge, sway, and heave motions were reduced by 39.5 %, 41.6 %, and 46.1 % and roll, pitch, and yaw motions were 48.2 %, 50.6 %, and 36.5 %, respectively, as compared with the values under uniform wind speed. It was confirmed that the developed inlet boundary condition describing the wind speed gradient with respect to height features higher accuracy than the boundary condition of uniform wind speed. The insights obtained in this study can be useful for the development of a numerical computation method for ships.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.2
• /
• pp.370-376
• /
• 2022

Smart ships related studies are being conducted in various fields owing to the development of technology, and an engine room patrol robot that can patrol the unmanned engine room is one such study. A patrol robot moves around the engine room based on the information learned through artificial intelligence and checks the machine normality and occurrence of abnormalities such as water leakage, oil leakage, and fire. Study on engine room patrol robots is mainly conducted on machine detection using artificial intelligence, however study on movement and control is insufficient. This causes a problem in that even if a patrol robot detects an object, there is no way to move to the detected object. To secure maneuverability to quickly identify the presence of abnormality in the engine room, this study experimented with whether a patrol robot can determine the shortest path by applying the A* algorithm. Data were obtained by driving a small car equipped with LiDAR in the ship engine room and creating a map by mapping the obtained data with SLAM(Simultaneous Localization And Mapping). The starting point and arrival point of the patrol robot were set on the map, and the A* algorithm was applied to determine whether the shortest path from the starting point to the arrival point was found. Simulation confirmed that the shortest route was well searched while avoiding obstacles from the starting point to the arrival point on the map. Applying this to the engine room patrol robot is believed to help improve ship safety.

• Journal of Chest Surgery
• /
• v.41 no.5
• /
• pp.659-662
• /
• 2008

Video-assisted pulmonary lobectomy was introduced in the early 1990's by several authors, and the frequency of video-assisted thoracic surgery (VATS) lobectomy for lung cancer has been slowly increasing because of its safety and oncologic acceptability in patients with early stage lung cancer However, VATS is limited by 2D imaging, an unsteady camera platform, and limited maneuverability of its instruments. The da Vinci Surgical System was recently introduced to overcome these limitations. It has a 3D endoscopic system with high resolution and magnified binocular views and EndoWrist instruments. We report three cases of da Vinci robot system-assisted pulmonary lobectomy in patients with early stage lung cancer.

• Journal of Biomedical Engineering Research
• /
• v.16 no.4
• /
• pp.543-554
• /
• 1995

This paper describes the improvement of driving stability and the control system for INMEL-VII which is motorized manual wheelchair to satisfy requirements of the disabled The INMEL-VI was based on high maneuverability of the omnidirection drive and safety But the results of field tests about two years showed some problems to the disabled in daily life such as driving stability, Pm switching noise, and rotation of motor without driving command on negative slope. To solve the problems due to an increased DC motor power and applied to direct connection method in INMEL- VII. It improved the driving circuits and set switching frequency to 5KHz to eliminate the switching noise caused by PWM control of DC motor, As compare with the INMEL-VI, INMEL-VII is improved in driving stability by transfer the weight center to forward. The results of field testing proved the improvement of the driving stability and software algorithm It has been estimated to have a hlgh practical use for powered walking aids to the disabled's daily life.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2006.10a
• /
• pp.157-165
• /
• 2006

In February,2004, at International Maritime Organization (IMO), LONDON, a new international convention 'International Convention fur the Control and Management of Ship's Ballast Water and Sediment 2004' was adopted. It is called 'Ballast Water Management Convention (BWM)'. Ballast water means charged seawater or fresh water in ship's special tanks (ballast tank) to keep safety navigation and ship's maneuverability. However, from 1980, it was point out the serious problem for marine ecosystem and human life that ballast water includes harmful marine species (and small organisms) and these species are also discharged along with ballast water. These species were released with discharged ballast water in water areas, where species are different from discharged ballast water. The problem is that released species increase when released species are more powerful than native species and consequently, marine ecological system is destroyed in released water area. Authors have inspected the validity of the ballast water exchange using pumping-through method that is one of the methods of ballast water management. In this paper, the numerical simulation of the motion and density of the fluid at the time of exchange of the fluid in a 2-dimensional tank using the pumping-through method was carried out by using two different type numerical methods. One method is MPS method that is one of the particle methods. Other one is Finite Different Method (FDM). Authors were compared with result of two numerical method calculations and experiment result and reported some knowledge from these results.