• Water for future
• /
• v.16 no.3
• /
• pp.171-179
• /
• 1983

In the Jeon Cheon Basin, unconsolidated alluvium and marine clay beds overlying Tertiary conglomerate and impermeable mudstone, and Cambro-Ordovician sedimentary rocks composed of mainly cavernous limestones, and age-unknowned crystalline rocks are occured. Most productive rock is Cambro-Ordovician limestones containing a lot of solution openings and secondary porosities and shows its transmissivity of 1836$m^2$/day and storativity of 1.47 $\times$ $10^{-3}$. The storage of deep seated groundwater in linestone aquifer is estimated about 1059 $\times$ $10^6$ metric tons, being equivalent to 6 years total precipitation of the basin. The safe yield of the groundwater to be abstracted from the aquifer is about 126,000 tons/day. To pump at least 100,000 tons/day of groundwater from the said aquifer, a well field comprising 34 deep wells ranging in depth from 80 to 100 meter and penetrating the cavernous limestone aquifer shall be established at middle and down stream area.

• Structural Engineering and Mechanics
• /
• v.5 no.5
• /
• pp.507-521
• /
• 1997

The ultimate behavior of a reinforced concrete hyperbolic paraboloid saddle shell under uniformly distributed vertical load is investigated using an inelastic, large displacement finite-element program originally developed at North Carolina State University. Unlike with the author's previous study which shows that the saddle shell possesses a tremendous capacity to redistribute the stresses, introducing tension stiffening in the model the cracks developed are no longer through cracks and formed as primarily bending cracks. Even though with small tension stiffening effect, the behavior of the shell is changed markedly from the one without tension stiffening effect. The load-deflection curves are straight and the slope of the curves is quite steep and remains unchanged with varying the tension stiffening parameters. The failure of the shell took place quite suddenly in a cantilever mode initiated by a formation of yield lines in a direction parallel to the support-to-support diagonal. The higher the tension stiffening parameters the higher is the ultimate load. The present study shows that the ultimate behavior of the shell primarily depends on the concrete tensile characteristics, such as tensile strength (before cracking) and the effective tension stiffening (after cracking). As the concrete characteristics would vary over the life of the shell, a degree of uncertainty is involved in deciding a specified ultimate strength of the saddle shell studied. By the present study, however, the overload factors based on ACI 318-95 are larger than unity for all the cases studied except that the tension stiffening parameter is weak by 3 with and without the large displacement effect, which shows that the Lin-Scordelis saddle shell studied here is at least safe.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.2
• /
• pp.24-29
• /
• 2020

In South Korea, agricultural mechanization has been carried out in paddy field, but not in the upland field during recent decades. Among crops such as root vegetables, leafy vegetables from upland field, corn is used as forage for livestock as well as food for men. The corn harvester needs to be developed to replace men's labor in rural area to follow the recent needs in the farm industry. The corn harvester is comprised of three parts such as cutting part, feeding part and pick-up part. The feeding part is so long for cut corns to be delivered from the cutting part to the pick-up part. Structurally, the load from the long moment arm is likely to be big. Thus, the setup to measure the stress on the duct of the feeding part was configured with the data acquisition system. The strain gages were attached on several points that seem to be loaded a lot comparatively. The stress was measured and the measured stresses were divided by the yield stress to get the safety factor. And then, we made sure the safety factors were above 1 on the all points. In conclusion, the feeding part of the corn harvester which convey the cut corn from the cutting part from the pick-up part can be regarded to be made safe structurally.

• Journal of the Korean Institute of Gas
• /
• v.19 no.1
• /
• pp.23-27
• /
• 2015

The stress and deformation behavior safeties of cylindrical hollow rollers have been analyzed by the finite element method, and investigated for over design capability based on the computed results. According to the stress analysis result which is related to the strength of a hollow roller, the maximum stress of 39.8MPa in which is operated near the bearing for supporting a hollow roller structure is overestimated design as 15.9% level compared with a yield strength, 250MPa of a steel material. And the maximum deformation of 0.032mm in which is operated at the middle span of a total length of cylindrical hollow rollers is very small and sufficiently safe compared with a total length and a thickness of a hollow roller. Thus, the FEM computed results for a stress and deformation indicate that a current FEM analysis model of cylindrical hollow rollers is over designed.

• Journal of Drive and Control
• /
• v.14 no.2
• /
• pp.23-29
• /
• 2017

In this study, a flexible multi-body dynamic simulation model of a knuckle boom crane is developed to evaluate the stress of spindle and rack gears under dynamic working conditions. It is difficult to predict potential critical damage to a knuckle boom crane if only the static condition is considered during the development process. To solve this issue, a severe working scenario (high speed with heavy load) was simulated as a boundary condition for testing the integrity of the dynamic simulation model. The crane gear model is defined as a flexible body so contact analysis was performed. The functional motion of a knuckle boom crane is generated by applying forces at each end of the rack gear, which was converted from hydraulic pressure measured for the experiment. The bending and contact stress of gears are theoretically calculated to validate the simulation model. In the simulation, the maximum stress of spindle and rack gears are observed when the crane abruptly stops. Peak impact force is produced at the contact interface between pinion and rack gears due to the inertia force of the boom. However, the maximum stress (bending/contact) of spindle and rack are under the yield stress, which is safe from damage. By using the developed simulation model, the experiment process is expected to be minimized.

• Journal of Pharmacopuncture
• /
• v.17 no.1
• /
• pp.35-43
• /
• 2014

Objectives: This study was performed to analyze the single dose toxicity of Chukyu (spine-healing) pharmacopuncture. Methods: All experiments were conducted at the Biotoxtech, an institution authorized to perform non-clinical studies under the regulations of Good Laboratory Practice (GLP) regulations. Sprague-Dawley rats were chosen for the pilot study. Doses of Chukyu (spine-healing) pharmacopuncture, 0.1, 0.5 and 1.0 mL, were administered to the experimental groups, and a dose of normal saline solution, 1.0 mL, was administered to the control group. This study was conducted under the approval of the Institutional Animal Ethic Committee. Results: No deaths or abnormalities occurred in any of the four groups. No significant changes in weight, hematological parameters or clinical chemistry between the control group and the experimental groups were observed. To check for abnormalities in organs and tissues, we used microscopy to examine representative histological sections of each specified organ; the results showed no significant differences in any of the organs or tissues except in one case, where interstitial infiltrating macrophages were found in one female rat in the 0.5-mL/animal experimental group. Conclusion: The above findings suggest that treatment with Chukyu (spine-healing) pharmacopuncture is relatively safe. Further studies on this subject are needed to yield more concrete evidence.

• Journal of Society of Preventive Korean Medicine
• /
• v.9 no.2
• /
• pp.107-123
• /
• 2005

Traditional herbal medicine is widely used among the Korean people, and other eastern Asian countries employ similar therapies as well. In recent years, due to increasing interest in herbal medicine, many researches have been made on the toxicity and adverse drug reactions of herbal medications. Through private and public media, there have been many opinions that taking herbal medicine is very harmful, especially, to liver and kidney. We face upon evaluation of herbal medication, safe, and efficacy. Furthermore, we need to control quality of herbs. This study aims to verify the evidence that taking herbal medicine will yield equal reaction in 2 lab animal groups (A and B). One frequently prescribed herbal medication, Yugmijihwangtang, was used to test the evaluation of quality on lab animals (SD-Rat). There were no significant differences in body, visceral weight, and serum analysis test results after herbal medication for 1 month. But, AST and ALT scores were raised in 2 subjects in group A (over reference range). It seems to be an adverse drug reaction, and this finding was restricted in group A herbal medicine. These results suggest that we need to qualify herbal plants in Korea, and study which herbs would cause specific reactions in human.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.11
• /
• pp.1331-1337
• /
• 2013

This study deals with the structural optimization of hybrid vertical-axis wind turbine blades using a response surface method (RSM). The structural analysis results suggest that the stress of hybrid vertical-axis wind turbine blades exceeds the yield strength. Optimization techniques are then applied to structural design to ensure a safe structure. First, the design factors that strongly influence the structural response are identified. The RSM was applied based on the design of experiments. The objective function and constraint terms set the weight and allowable stress, respectively. Furthermore, sensitivity analysis was conducted to indicate the effects of the design factors on the stress and weight. Finally, structural design was performed for the hybrid vertical-axis wind turbine blade.

• Water for future
• /
• v.27 no.1
• /
• pp.79-88
• /
• 1994

This study was conducted to analyse groundwater flow in the Bugok hot spring area using the MODFLOW model which can simulate three dimensional groundwater flow both in confined and unconfined aquifers. Based on this study the following conclusions were obtained: 1) The hydraulic conductivity and the specific storage of the aquifer were 0.0135 m/day and 0.020, respectively, and the model-predicted groundwater elevation agreed well with the observed one. 2) Simulation results showed that the groundwater level declines at the end of the one-year simulation period when the annual recharge rate is small and the annual pumping rate high, which is the worst combination. Except that combination, the groundwater level does not decline at the end of one-year simulation period indication the pumping rates used were allowable. 3) The safe yield depends upon the magnitudes of the recharge and pumping rates. The pumping rate should not produce excess decline of groundwater level around April when the water level is the lowest in a year.

• Journal of Pharmacopuncture
• /
• v.18 no.3
• /
• pp.63-67
• /
• 2015

Objectives: This study was performed to analyze the single-dose oral toxicity of the super key (processed sulfur). Methods: All experiments were conducted at Medvill, an institution authorized to perform non-clinical studies, under the Good Laboratory Practice (GLP) regulations. In order to investigate the oral toxicity of super key. We administered it orally to Sprague-Dawley (SD) rats. The SD rats were divided into four groups of five male and five female animals per group: group 1 being the control group and groups 2, 3, and 4 being the experimental groups. Doses of super key 500 mg/kg, 1,000 mg/kg and 2,000 mg/kg were administered to the experimental groups, and a dose of normal saline solution, 10 mL/kg, was administered to the control group. We examined the survival rates, weights, clinical signs, gross findings and necropsy findings. This study was conducted under the approval of the Institutional Animal Ethics Committee. (Approval number: A01-14018). Results: No deaths or abnormalities occurred in any of the four groups. Although slight decreases in the weights of some female rats were noted, no significant changes in weights or differences in the gross findings between the control group and the experimental groups were observed. To check for abnormalities in organs, we used microscopy to examine representative histological sections of each specified organ; the results showed no significant differences in any of the organs. Conclusion: The results of this research showed that administration of 500 - 2,000 mg/kg of super key did not cause any changes in the weights or in the results of necropsy examinations. Neither did it result in any mortalities. The above findings suggest that treatment with super key is relatively safe. Further studies on this subject are needed to yield more concrete evidence.