• Clean Technology
• /
• v.27 no.1
• /
• pp.24-32
• /
• 2021

Unburned carbon (UC) was successfully separated from fly ash by up to 85.8% in weight via froth flotation using soybean oil as a collector. An 18 wt% yield of microceramics (CM) could be achieved by employing a hydro cyclone separator located immediately after the flotation equipment. UC and CM were tested as alternatives to weight-adding material and polymer (especially polypropylene in this study) filler, respectively. Large particles of UC were broken down into smaller ones via ball milling to have an average particle diameter of 10.2 ㎛. When crushed UC was used as an alternative to clay as a rubber weight-adding material, a somewhat lower tensile strength and elongation rate than the allowed values were unfortunately obtained. In order to satisfy the standard limits, further treatment of UC is required to enhance surface energy for more intimate bonding with rubber. CM was observed in spherical forms with an average diameter of 5 ㎛. The surface of the CM particles was modified with phenol, polyol, stearic acid, and oleic acid so that the surface modified CM could be used as a polypropylene-filling agent. The flowability was good, but due to the lack of coupling forces with polypropylene, successful impact strength and flexural strength could not be obtained. However, when mixing the surface-modified CM with 1% silane by weight, a drastic increase in both the impact strength and flexural strength were obtained.

• Journal of the Korean Electrochemical Society
• /
• v.24 no.4
• /
• pp.100-105
• /
• 2021

Recently, all-solid-state batteries have attracted much attention to improve safety of rechargeable lithium batteries, but the solid-state batteries of conductive ceramics or solid polymer electrolytes show poor electrochemical properties because of several problems such as high interfacial resistance and undesired reactions. To solve the problems of the reported all-solid-state batteries, a hybrid solid electrolyte is suggested, in this study, NASICON-type nanoparticle Li_1.5Al_0.5Ti_1.5P₃O₁₂ (LATP) conductive ceramic, PVdF-HFP, and a carbonate-based liquid electrolyte were composited to prepare a quasi-solid electrolyte. The hybrid solid electrolyte has a high voltage stability of 5.6 V and shows an suppress effect of lithium dendrite growth in the stripping-plating test. The LiNi_0.83Co_0.11Mn_0.06O₂ (NCM811)-based battery with the hybrid solid electrolyte exhibits a high discharge capacity of 241.5 mAh/g at a high charge-cut-off voltage of 4.8V and stable electrochemical reaction. The NCM811-based battery also shows 139.4 mAh/g discharge capacity without short circuit or explosion at 90℃. Therefore, the LATP-based hybrid solid electrolyte can be an effective solution to improve the safety and electrochemical properties of rechargeable lithium batteries.

• Restorative Dentistry and Endodontics
• /
• v.23 no.1
• /
• pp.141-161
• /
• 1998

The depth and patterns of demineralization according to the difference in concentration and application time of phosphoric acid were observed through the transmission electron microscope, and shear bond strengths to the acid -conditioned dentin were then measured and compared with the TEM results. To investigate the influence of polymer addition into the phosphoric acid and the effect of difference in concentration and application time of the acid, the specimens were randomly divided into 9 groups. Among the specimens, the exposed dentin surfaces were acid-conditioned with 10% polymer-thickened phosphoric acid(All Bond 2, Bisco, U.S.A.) and aqueous 10%, 20%, 30%, 40% phosphoric acid for 20 seconds, The rest of the specimens were acid-conditioned with 10% phosphoric acid for 15s, 30s, 60s, 120s respectively. The specimens were immersed in 4% glutaraldehyde in 0.1M sodium cacodylate buffer and postfixed with 1 % osmium tetroxide without decalcification and then observed under a JEOL Transmission Electron Microscope(JEM 1200 EX II, Japan). After the specimens were acid-conditioned as the above, primer and adhesive resin were applied to blot-dried dentin and shear bond strengths were then measured and analysed. The results were as follows : 1. The intertubular demineralization depth of 4.0-$5.0{\mu}m$ in 10% polymer-thickened phosphoric acid gels was similar or slightly deeper than that of 4.0-$4.5{\mu}m$ in aqueous 10% phosphoric acid solution. 2. The intertubular demineralization depth of aqueous 20%, 30% and 40% phosphoric acid solution was 6.5-$7.0{\mu}m$, 6.5-$7.5{\mu}m$ and 9.0-$15.0{\mu}m$ respectively. It showed that the depth of dentin demineralization is partly related to the concentration of phosphoric acid solution. 3. The intertubular demineralization depth of aqueous 10% phosphoric acid solution in application time for 15s, 30s, 60s and 120s was 2.5-$3.0{\mu}m$, 4.0-$6.0{\mu}m$, 6.5-$7.0{\mu}m$ and 8.5-$14.0{\mu}m$ respectively. It showed that the depth of dentin demineralization is directly related to the application time of phosphoric acid solution. 4. The partially demineralized dentin layer between demineralized collagen layer and unaffected dentin was showed to a width of 0.5-$1.0{\mu}m$ in lower concentration groups treated with aqueous 10% phosphoric acid for 20s, 60s, 120s and 20% phosphoric acid for 20s. 5. The demineralization effect at the border of intertubular-peritubular junction was less evident than that in the peritubular and intertubular dentin. The collagen fibers in the intertubular dentin had a random orientation, whereas those that lined the tubules were circumferentially aligned. The cross-linkage of dentinal collagen in demineralized collagen layer was clearly seen. 6. A statistically significant difference of bond strengths according to the difference in phosphoric acid concentration did not exist among the groups treated with 10%, 20%, 30% and 40% acid solution (P>0.05). However, bond strengths to the treated dentin with 10% phosphoric acid solution for 30s were significantly higher than that for 120s (P<0.05).

• Applied Chemistry for Engineering
• /
• v.8 no.2
• /
• pp.172-178
• /
• 1997

Polyaniline(PANI)-stearic acid(SA) composite monolayer was formed at the air-water interface. The stearic acid as a surfactant was used to promote PANI monolayer formation. Uniform PANI-SA monolayer assemblies with Y type and transfer ratio of ca. 1 were fabricated using the Langmuir-Blodgett(LB) technique. The PANI-SA composite LB films with high electrical conductivity of $10^{-1}{\sim}10^{-2}S/cm$ were obtained by doping of HCl or $I_2$, and their conductivity revealed essentially close value as that of conventional PAHI-HCl complex. Especially, iodine is found to be the most promising dopant, since it gives a remarkable stability for the application as a polymer electrode in the MIM molecular device consisted of acceptor, sensitizer, and donor. The structure and physical properties of PANI-SA LB films were investigated through the near-ir UV, FT-IR, and Cyclic voltammetry.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.1
• /
• pp.171-178
• /
• 2019

Fiber-reinforced polymer (FRP) composites have proved to be reliable as strengthening materials. Most of existing studies used single types of FRP composites. Therefore, in this experimental study, carbon FRP sheet, aramid FRP sheet, and hybrid FRP plate including glass fibers were fabricated, and the effect of pre-stressed FRP composites on flexural strengthening of reinforced concrete (RC) beams was investigated. In total, eight RC beam specimens were fabricated, including one control beam (specimen N) without FRP composites and seven FRP-strengthened beams. The main parameters were type of FRP composite, the number of anchors used for pre-stressing, and thickness of FRP plates. As a result, the beam strengthened with pre-stressed FRP plate showed superior performance to the non-strengthened one in terms of initial strength, strength and stiffness at yielding, and ultimate strength. As the number of anchors and thickness of FRP plate (i.e., amount of FRP plates) increased, the strengthening effect increased as well. When hybrid FRP plates were pre-stressed, the strengthening effect was higher in comparison with pre-stressed single type FRP plate.

• Journal of Food Hygiene and Safety
• /
• v.24 no.4
• /
• pp.352-356
• /
• 2009

The purpose of this study was to introduce the toxicological study review to evaluate the safety of PDMS on the 69th JECFA meeting. Polydimethylsiloxane is a polymer and its ADI was established at 23rd JECFA meeting in 1979. The ADI was maintained although the specification was expanded at its 26th, 29 th, 37 th meetings. Recently, it was reported that PDMS with low molecular weight and viscosity has high absorption rate and different toxicity, so it was submitted at 69th meeting. Toxicological studies of PDMS were submitted from the sponsor and additional information is collected from a document searching. The toxicological studies were reviewed in accordance with the 'Guidelines for the preparation of toxicological working papers for the Joint FAO/WHO Expert Committee on Food Additives'. In the available acute, sub-chronic and chronic toxicity studies on PDMS, dose-related increases in incidence and severity of ocular lesions(corneal crystal, inflammation of the corneal epithelium etc.) were consistently observed after oral dosing. It seems to be a local irritant effect, but the mechanism by which the ocular lesions arose is unclear, although the lack of absorption of PDMS indicates that it is unlikely to be a direct systemic effect. Consequently, the relevance of the ocular lesions for food use of PDMS could not be determined. The ADI of PDMS was re-established from 0-1.5 mg/kg bw/day to 0-0.8 mg/kg bw/day by applying additional safety factor 2 based on its ocular toxicity. The result of 0-0.8 mg/kg bw/day is a temporary ADI until further data are provided to 2010.

• Journal of Sericultural and Entomological Science
• /
• v.25 no.1
• /
• pp.1-20
• /
• 1983

It has been known that the insect molting hormone and its analogues exist also in plant kingdom and their concentration has been found to be about 0.1~2.0% of dry matter, which is equivalent to $10^3{\sim}10^5$ times of those in insects. This study was carried out; 1) to isolate the phytoecdysones from Korean Achyranthes radix and characterize their physico-chemical properties. 2) to investigate the biological activity of this phytoecdysone on Bombyx mori larvae. The resuls were summarized as follows; 1. The extraction method of phytoecdysones was optimized by three consecutive reflux for 1hr using 200g of dried and milled radix per 1l methanol. 2. The purification from the crude extract was made by a series of steps such as precipitation of gum-type polymer with n-Butyl acetate, adsorption on technical grade silica and chromatography with neutral alumina. The conditions of each step were optimized and the resulting crude crystal was about 500mg per kg dry radix. 3. The crude crystal from the cultivated Achyranthes(Achyranthes japonia) contained ecdysterone (20-hydroxyecdysone) and inokosterone in the proportion of one to one. In order to separate these, a series of processes such as acetylation, separation by alumina column chromatography deacetylation by alcoholysis, deionization and crystallization were introduced and optimized 125mg of ecdysterone and 18mg of inokosterone per kg dry radix were thus obtained. 4. The wild Achyranthes (Achyranthes obtusifolia) radix was found to contain the ecdysterone only. A 285mg of ecdysterone was crystallized per kg dry radix. 5. Isolated ecdysterone, inodosterone and acetylated compounds were characterized by IR., UV., NMR spectroscopy, mp, TLC and densitometry. 6. Ligation experiment was undertaken to confirm the biological activity of the purified ecdysterone; the ecdysterone could induce larval-pupal metamorphosis in the ligated abdomen of 4th instar larvae injecting 0.5~1.0${\mu}g$. 7. By ecdysterone feeding experiment using artificial diet, it was elucidated that the critical time of feeding would be the first half of each instar resulting in increased weight of silk layer. 8. The ecdysterone was fed to 5th instar silkworm at the level of 1, 2, 3, 5ppm of dry feed of artificial diet containing 5% mulberry leaves for 72hrs. At 2ppm of the concentration. body weight and silk layer weight were arrived at maximum. But at higher concentrations body weight and silk layer weight decreased than the control group. At 2ppm of the concentration, body weight was increased by 12.5%. 9. Feeding 2ppm of ecdysterone at the later half of 5th instar, the duration of larvae was shortened.