• Journal of the Institute of Convergence Signal Processing
• /
• v.12 no.3
• /
• pp.163-168
• /
• 2011

In this paper, we proposed non-linear gamma curve algorithm for gamma correction. The previous non-linear gamma curve algorithm is generated by the least square polynomial using the Gauss-Jordan inverse matrix. However, the previous algorithm has some weak points. When calculating coefficients using inverse matrix of higher degree, occurred truncation errors. Also, only if input sample points are existed regular interval on 10-bit scale, the least square polynomial is accurately works. To compensate weak-points, we calculated accurate coefficients of polynomial using eigenvalue and orthogonal value of mat11x from singular value decomposition (SVD) and QR decomposition of vandemond matrix. Also, we used input data part segmentation, then we performed polynomial curve fitting and merged curve fitting results. When compared the previous method and proposed method using the mean square error (MSE) and the standard deviation (STD), the proposed segmented polynomial curve fitting is highly accuracy that MSE under the least significant bit (LSB) error range is approximately $10^{-9}$ and STD is about $10^{-5}$.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.2
• /
• pp.35-40
• /
• 2011

We have studied the impact and bending characteristics of a dual band antenna (1.575, 2.645 GHz) with composite sandwich construction. Mechanical performance of the antenna can be improved by reinforcing the antenna by sandwiching the planar antenna with layers of carbon fiber-reinforced plastic(CFRP) and glass fiber-reinforced plastic(GFRP) using an adhesive film. According to the ASTM D7137, ASTM C393 and MIL-STD401B, impact and bending test were performed and the S-parameters and gains of the antenna were measured in order to verify electrical and mechanical performance. The maximum contact load and the bending load of the antenna are 4 kN and 400 N and gains of the antenna are 6 dBi and 4.6 dBi in the GPS and DMB bands, respectively. The proposed antenna structure can be applied to surfaces of vehicles.

• Journal of the Korean Society for Heat Treatment
• /
• v.14 no.1
• /
• pp.8-16
• /
• 2001

The effects of gas composition, pressure, temperature and time on the case thickness, hardness and nitride formation in the surface of tool steels(STD11 and STD61) have been studied by micro-pulse plasma nitriding. External compound layer and internal diffusion layer and the diffusion layer were observed in the nitrided case of tool steels. The relative amounts and kind of phases formed in the nitrided case changed with the change of nitriding conditions. Generally, only nitride phases such as ${\gamma}(Fe_4N)$, ${\varepsilon}(Fe_{2-3}N)$, or $Cr_{1.75}V_{0.25}N_2$ phases were detected in the compound layer, while nitride and carbide phases such as ${\varepsilon}-nitride(Fe_{2-3}N)$, $(Cr,Fe)_{\gamma}C_3$ or $Fe_3C$ were detected in the diffusion layer by XRD analysis. The thickness of compound layer increased with the increase of nitrogen content in the gas composition. Maximum case depth was obtained at gas pressure of 200Pa.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.4
• /
• pp.100-110
• /
• 1995

This paper aims at reviewing the possibility of application over normal or abnormal, detection used by AE, and the characteristics of grinding processes. In this study, when WA-vitri-fied ' resinoid bond grinding wheels:36 kinds of grinding wheel and grinding depth were tuned at the surface grinding, the zone of AE signal generation is theoretically modelled and reviewed by grinding processes. The variation of grinding resistance( F$n^{9}$ $F_{t}$) and AE signal is detected in-process by the use of AE measuring system. The tests are carried out in accordance with grain size and grade of grinding wheels, and work-pieces-STD11 and STD61. According to the experiment's results, the following can be expected;as grinding time passes by, the relation of grinding depth and quantity of AE signal, observing on AE signal and grinding burn suggest the characteristics of grinding processes and evalution on the possibility of control of grinding machine, and monitoring abnormal conditions.e, and monitoring abnormal conditions.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.10
• /
• pp.11-20
• /
• 2002

This paper proposes a hardware/software codesign of the MLSE equalizer for GSM.GPRS systems. We analyze algorithms of the MLSE equalizer which consists of a channel estimator using the correlation method and the Viterbi processor. We estimate the computational complexity requirement based on the simulation of TI TMS320C5x DSP. We also estimate the gate count from the results of logic synthesis using the samsung 0.5㎛ standard cell library (STD80). Based on the results of the complexity estimation and gate count, we propose the efficient software/hardware codesign of the MLSE equalizer based on the results of the complexity estimation and gate count.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.11C
• /
• pp.1052-1057
• /
• 2006

The implement the adaptive partial response maximum likelihood (PRML) detector with tilt analyzer for asymmetric high-density optical storage system. For the estimation of disc tilt, we exploit spc patterns in each data frame. Because of using the ROM table to renew the coefficients of equalizer and reference values of branches, the complexity of the hardware is reduced. The proposed PRML has been designed and verified by VerilogHDL and synthesized by the Synopsys Design Compiler with Hynix $0.35{\mu}m$ STD cell library. In the result, the total gate count is 35K, and the maximum operating frequency is 140MHz.

• Korean Journal of Materials Research
• /
• v.11 no.4
• /
• pp.324-328
• /
• 2001

CrN films were deposited onto STD61 steel substrates using an arc-ion plating apparatus, with and without ion-nitriding pretreatment, and their oxidation was studied between 700 and $900^{\circ}C$ for 40hr in air. The oxidation behavior was examined by thermogravimetric analyses, X-ray diffraction. EDS and SEM. The deposited CrN films consisted of CrN and $Cr_2$N phases. The CrN films increased the oxidation resistance of the substrate by forming a protective $Cr_2$$O_3$ layer. The ion-nitriding pretreatment has not affected the oxidation resistance of the CrN film.

• Journal of the Korean Society of Industry Convergence
• /
• v.8 no.4
• /
• pp.227-234
• /
• 2005

In this study an experimental investigation was conducted to assesment of cutting ability for CBN ball end-milling, STD11 and NAK80 materials. The cutting force and surface roughness of the work-pieces were obtained in machining center. The assessment of CBN tools were inspected through the tool dynamotor and SEM. When $30^{\circ}$ negative rake angle, the wear and cutting force were good, surface roughness was better at cutting fluid during CBN cutting.

• Tribology and Lubricants
• /
• v.16 no.4
• /
• pp.253-258
• /
• 2000

Frictional behavior of wire electric discharge machined surfaces of spheroidized annealed STDll steel was investigated. The surfaces were produced with a various series of finish cuts where pulse energy was reduced with increase in the number of finish cuts. Roughness and micro-hardness of the surfaces were also measured. It is observed that the increase in the number of finish cuts produces the surface exhibiting lower frictional resistance followed by higher resistance after considerable wear. Effects of finish cuts on the friction characteristics are discussed with the aid of roughness and micro-hardness of the surfaces.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.106-112
• /
• 2003

High-speed machining is one of the most effective technology to improve productivity. Because of the high speed and high feed rate, high-speed machining can give great advantages for the machining of dies and molds. This paper describes on the improvement of machining accuracy in high-speed machining and an estimate about machining accuracy of high-speed machining.