• Journal of KSNVE
• /
• v.11 no.2
• /
• pp.307-314
• /
• 2001

This study aims to provide fundamental data for enhancing the sound insulation performance of windows. For this study, windows composed of various types and thicknesses, were classified into five categories； fixed, single, double, triple and airtight, and then tested. In order to analyze their sound insulation characteristics and performances. test results were rated using methods such as D, STC, Ts and arithmetical mean. It was found that the sound insulation performance of windows is affected due to their type rather than the thickness of the glass. It was also found that when gap between the inner and outer frames was filled with caulking material, the sound transmission loss at high frequency bands was greatly improved. Therefore, the sound insulation performance of windows would be enhanced by minimizing the gap between frames.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.310-310
• /
• 2010

태양전지의 양자효율이란 입사되는 광자 수에 대한 태양전지에 의해 수집되는 캐리어 수의 비를 의미한다. 본 연구에서는 결정질, 다결정질, 비정질 실리콘 태양전지 양자효율 측정 정확도 향상에 대하여 연구하였다. 태양전지 양자효율 측정에 어떠한 변수들이 영향을 미치고 정확한 측정을 하기위해서는 측정을 어떻게 하여야 하는가에 대한 실험을 하였다. 태양전지 특성분석은 실제 사용 환경에 맞도록 표준측정조건(standard test condition: STC)에서 측정한 데이터를 사용하여야 한다. 이 표준측정조건은 AM1.5G 스펙트럼, $100\;mW/cm^2$의 강도 및 온도 $25^{\circ}C$에서의 측정을 말한다. 조건에 맞지 않는 측정을 할 경우 어떠한 변화가 있는지와 어떻게 측정을 하는 것이 정확한 측정인가에 대한 연구를 진행하였다. 바이어스 광의 강도와 쵸핑 주파수에 따라 측정을 진행하였고, 태양전지의 분광반응도(spectral response: SR)를 측정하여 이를 이용하여 양자효율을 계산하였고, 양자효율 결과를 토대로 분석을 진행하였다.

• Electric Engineers Magazine
• /
• s.334
• /
• pp.30-35
• /
• 2010

본 고에서는 현장에 설치된 태양광발전시스템의 출력 측정 방법을 제시 하였다. 태양광발전시스템은 햇빛이라는 자연조건에 따라서 출력이 수시로 변동하기 때문에 태양전지 제조자가 제시하는 규격은 제작시에 태양전지를 표준 시험조건(즉, STC, Air Mass 1.5, 일사량 1000[$W/m^2$], 온도 $25^{\circ}C$기준)에서 시험한 성능 규격을 제시하고 있다. 그러나 적용현장에 설치된 태양전지는 인위적으로 표준 시험조건을 만들어 줄 수 없기 때문에 출력을 측정하면 제조자가 제시한 성능 규격이 제대로 나오는지 여부가 관심사다. 그렇기 때문에 설치현장에서 자연 조건에서 측정된 출력에다 태양전지 제작사에서 제시한 온도 및 일사량 특성곡선에서 추출된 보정계수를 적용하여 보정 출력을 산정해서 보정 출력을 토대로 제조사에서 제시한 규격에 부합하는 지 여부를 판단할 수 있는 방법을 제안하였다.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.2
• /
• pp.27-37
• /
• 1991

The adhesion strength of TiN films to substrate(STC 3) steel has been studied using the scratch adhesion test. Before deposition, the substrates were mechanically polished and TiN films were deposited at different substrate temperature($480^{\circ}C-540^{\circ}C$). The chemical properties of TiN films were investigated by RBS, and EDS, and the physical properties were investigated by micro-hardness tester, SEM, and X-ray diffractometer. According to results of this study, the adhesion strength of TiN films increase with increasing the deposition temperature. The roughness of the polished substrates surface were measured with a profilometer. It was observed that, as a general rule, the adhesion strength of deposited TiN films increase with decreasing the substrates surface roughness.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.6
• /
• pp.112-119
• /
• 1995

Early fracture and cutting force of ceramic tool for hardened STC3 steel was investigated in this study. It was found that early fracture of ceramic tool was mostly occurred before normal wear was progressed beyond a critical cutting speed and normal wear was performed under the critical cutting speed. The relationships among critical cutting speed, which was a cause of early fracture, suggested cutting cross section, that is, maximum thickness of cut and width of cut, and cutting force were examined. The following conclusions were obtained: (1)Critical cutting speed showed a high value in the case of small maximum thickness of cut and large nose radius, but was not influenced by width of cut, (2)Principal, feed and radial force, respectively, showed the proportional value to constant cutting area, width of cut and maximum thickness of cut orderly, (3)Occurrence of early fracture was dependent upon radial force.

• Journal of the Korean Society for Heat Treatment
• /
• v.2 no.4
• /
• pp.11-18
• /
• 1989

To investigate the influence of $TiCl_4$, $N_2$ inlet fraction on the TiN layer, TiN film was deposited onto the STC3 and STD11 steel from gas mixtures of $TiCl_4/N_2/H_2$ by the radio frequency plasma assisted chemical vapor deposition. The films were deposited at various $TiCl_4$, $N_2$ inlet fractions. The results showed that the film thickness was increased with $TiCl_4$ inlet fraction. However, while the thickness was increased with $N_4$ inlet fraction under 0.4 the thickness was decreased with increasing $N_2$ inlet fraction over 0.4. The density of deposited films was varied as $TiCl_4$, $N_2$ inlet fraction and its maximum value was about $5.6g/cm^3$. The contents of chlorine were increased with increasing $TiCl_4$ inlet fraction and nearly constant with increasing $N_2$ inlet fraction.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.61 no.4
• /
• pp.251-256
• /
• 2016

The increase in carbon stock and sustainability of crop production are the main challenges in agricultural fields relevant to climate change. Methane is the most important greenhouse gas emitted from paddy fields. This study was conducted to investigate the effects of tillage and cultivation methods on methane emissions in rice production in 2014 and 2015. Different combinations of tillage and cultivation were implemented, including conventional tillage-transplanting (T-T), tillage-wet hill seeding (T-W), minimum tillage-dry seeding (MT-D), and no-tillage-dry seeding (NT-D). The amount of methane emitted was the highest in T-T treatment. In MT-D and NT-D treatments, methane emissions were significantly decreased by 77%, compared with that in T-T treatment. Conversely, the soil total carbon (STC) content was higher in MT-D and NT-D plots than in tillage plots. In both years, methane emissions were highly correlated with the dry weight of rice ($R^2=0.62{\sim}0.96$), although the cumulative emissions during the rice growing period was higher in 2014 than in 2015. T-T treatment showed the highest $R^2$ (0.93) among the four treatments. Rice grain yields did not significantly differ with the tillage and cultivation methods used. These results suggest that NT-D practice in rice production could reduce the methane emissions and increase the STC content without loss in grain yield.

• The Journal of Korean Academy of Prosthodontics
• /
• v.33 no.2
• /
• pp.210-230
• /
• 1995

To compare the wear resistance of four kinds of commercial acrylic resin teeth [SR-Orthosit PosterioresR(Ivoclar Co., Liechtenstein), Endura PosteriorR(Shofu Inc. Japan), trubyte IPN teethR(Dentsply International Inc., York,), Trubyte BiotoneR(dentsply Inermational Inc. Brazil) by means of the toothbrush abrasion method, the artificial resin teeth were embedded in epoxy resin with the occlusal surfaces aligned in one plane for a total of 40 blocks. There after, each lock was mounted in the arm of the toothbrush abrasion machine(K 236, Japan). Wear measurements were made on the three preconditioned states. Those were as follows : no treatment specimens, thermocycled specimens, and thermocycled specimens which were immeresed applied load of 400g during the buring the brushing cycle. At the end of the 30,000-stroke cycle, each specimen was removed, and weighed. The microhardness of four kinds of commercial resin teeth were determined by means of microhardness tester. Microhardness tests were performed on te no treatment specimens, thermocycled specimens, and thermocycled specimens with immersion in the denture cleansing solution. Finally, the comparison of thermal properties were perfomed using differential scanning calorimeter(DSC-1500). The following results were obtained : 1. In the case of no treatment teeth, the wear amount of endura Posterior(EN) was the greatest among the others(p<0.01), and the wear amount of three kinds of artificial resin teeth was increased in the order of Trubyte IPN teeth(IN), Trubyte Biotone(BN), SR-Orthosit Posteriores(SN) but there was no statistic significance(p>0.01). 2. The wear amount of Trubyte IPN teeth(IT) and Trubyte Biotone(BT), was increased due to thermocycling effect, but that of Endura Posteriores(ET) was decreased conversely(p<0.01). 3. Except for the SR-Orthosit Posteriores(STC), the wear amount of three kinds of artificial resing teeth(that is, ETC, ITC, BTC) was increased due to denture cleansing solution$(Cledent^R)$, but there was no statistic significance(p>0.01). But the wear amount of the SR-Orthosit Posteriores(STC) was the greatest among the others(p<0.01). 4. The wear amount of toothbrush was the greatest in case of contact with occlusal surface of SROrthosit Posteriores resin teeth(p<0.01). 5. the microhardness values(KHN) of the SR-Orthosit Posteriores was the highest among the experimental artificial resin teeth(p<0.01). 6. There was no relationship between microhardness valuse(KHN) and wear amount of four kinds of experimental artificial resin teeth(p<0.01). 7. The differential canning calorimetric property of four kinds of artificial resin teeth did not show endothermal or exothermal peak in the range of $100^{\circ}C$

• Journal of Radiation Protection and Research
• /
• v.29 no.4
• /
• pp.251-256
• /
• 2004

CsI(Tl), $CdWO_4(CWO),\;Bi_4Ge_3O_{12}(BGO)\;and\;Gd_2SiO_5:Ce(GSO)$ scintillators were studied to manufacture a phoswich detector. The maximum wavelengths of the CsI(Tl), CWO, BGO and GSO scintillators are 550 nm, 475 nm, 490 nm and 440 nm for the radioluminescence, and the absolute light outputs of the CsI(Tl), CWO, BGO and GSO scintillators are 54890 phonon/MeV, 17762 phonon/MeV, 8322 phonon/MeV and 8932 phonon/MeV with a neutral filter, and the decay time of the CsI(Tl), CWO, BGO and GSO scintillators is $1.3{\mu}s,\;8.17{\mu}s$, 213 ns and 37 ns by a single photon method. The phoswich detector which was manufactured with plastic and CsI(Tl) scintillators could separate the ${\beta}$ particle and ${\gamma}$ ray. The phoswich detector could also measure the pulse height spectra of the ${\beta}$ particle and ${\gamma}$ ray by a PSD method.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.4
• /
• pp.30-37
• /
• 1997

This thesis is concerned with the study on the characteristics of the tool failure occuring at the beginning of cutting in finish machining of hardened steels such as carbon tool steel and alloy tool steel by a ceramic tool (Al$_{2}$O$_{3}$+TiC) with nose radius. In the machining of hardened carbon steel STC3, the wear mechanism on the flank face of the ceramic tool is abrasion wear. The mode of tool failure is developed into catastropic fracture with flaking. It is thought that the fracture caused by FeO and TiO$_{2}$ results from the oxidation of Fe in the workpice and TiC in the ceramic tool and the deposit of Fe formed on the surface of the ceramic tool. In the machining of hardened alloy steel STD11, the wear mechanism on the flank face of the ceramic tool is that abrasion and adhesion wear exist simultaneously. The mode of tool failure at the beginning of cutting features is DOC notch wear. It is thought that the DOC notch wear caused by FeO and TiO$_{2}$results from the oxidation of Fe and TiC in the workpiece and ceramic tool, respectively.