• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.3
• /
• pp.394-400
• /
• 2012

In this paper, charging modes of series resonant converter for a high voltage energy storage capacitor are compared in terms of charging time, peak resonant current, normalized peak resonant current and voltage in each operation mode. Operating principles of the full bridge series resonant converter with capacitor load are explained and analyzed in discontinuous and continuous operation mode. Based on the analysis and simulation result, $0.6{\omega}_r$ < ${\omega}_s$ < $0.75{\omega}_r$ and $1.3{\omega}_r$ < ${\omega}_s$ < $1.4{\omega}_r$ are evaluated to the best range of switching frequency for charging of an high voltage energy storage capacitor. 1.8 kJ/s SRC prototype is assembled with TI 28335 DSP controller and 40 kJ, 7 kV energy storage capacitor. Design rules based on the comparative analysis are verified by experiment.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.11
• /
• pp.1441-1447
• /
• 1999

A discrete time domain modeling is presented for the pulse-width modulated series resonant converter (PWM-SRC) with a discontinuous current mode. This nonlinear system is linearized about its equilibrium state to obtain a linear discrete time model for the investigation of small signal performances such as the stability and transient response. The usefulness of this small signal model is verified through the dynamic simulation.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.530-533
• /
• 1987

In high-frequency switched mode converters, Series Resonant Converter (SRC) is investigated using state-plane method. Phase plane trajectories of the SRC permit a direct closed form solution of the steady state operation and can make problems easy to solve. This paper describes steady state responses and characteristics of the SRC with respect to various circuit factors. The magnitute of steady state response and the average current through load are clearly related to how such the switching frequency differs from the resonant frequency. The results of the steady state analysis can be used to estimate the device and component stress on the power circuit.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.1
• /
• pp.33-39
• /
• 2005

Comparing with the conventional transformer without the air gap, a contactless transformer with the large air gap between the long primary winding and the secondary winding has increased leakage inductance and reduced magnetizing inductance. For transferring the primary power to the secondary one, the high frequency series resonant converter has been widely used for the contactless power supply system with the large air gap and the increased leakage inductance of the contactless transformer However, the high frequency series resonant converter has the disadvantages of the low efficiency and high voltage gain characteristics in the overall load range due to the large air gap and the circulating magnetizing current. In this paper, the characteristics of the high efficiency and unit voltage gain are revealed in the proposed three-level series-parallel resonant converter. The results are verified on the simulation based on the theoretical analysis and the 5kW experimental prototype.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.3
• /
• pp.256-264
• /
• 2022

The frequency power control method (FCM) which has a wide operating frequency range is adopted for induction heating (IH) cooktops. When FCM is applied to the full-bridge series resonant converter (FB-SRC) based IH system, high-frequency switching of the inverter is required compared to the half-bridge SRC (HB-SRC)-based IH system. Therefore, the switching loss of the inverter increases, and applying FCM under the condition that the inverter operating frequency range is limited is difficult. Therefore, this paper proposes a control strategy with the phase shift power control method considering that limited frequency conditions are presented. Loss analysis following the control method is performed through simulation and mathematical analysis. In addition, the validity of the proposed control strategy is verified by analyzing the heating performance following the control method through the test results of the 3,200[W] prototype.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.8
• /
• pp.828-835
• /
• 1990

A new state feedback control scheme is proposed to improve the stability and dynamic performances of the series resonant converter (SRC). The proposed scheme can be easily implemented without speed limitation. Design parameter of the proposed control is the ratio of the state feedback gains. A closed loop dynamic modeling for the SRC with the proposed control law is derived. Parametric curves which can be used to select the design parameter in the control system are presented. The experimental results show that the excellent dynamic performance of the converter can be obtained by properly selecting the design parameter. The results are further compared with both the theoretical analysis and the frequency control.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.1
• /
• pp.24-31
• /
• 2018

An induction heating (IH) resonant converter, as well as its coil design method, is proposed in this study to improve the heat capability of low- and high-resistance IH vessels. Conventional IH resonant converters have been designed only for heating high-resistance containers designed for IH application. Thus, the primary current in the resonant tank becomes extremely high to transfer the rated power when the converter heats the low-resistance vessel. As a result, the rated power cannot be transferred due to overcurrent flows against the rated switch current. Hence, the optimal number of coil turns and proper operating frequency to heat high- and low-resistance vessels are proposed in this study by analyzing an IH load model. Simulation and experimental results using a 2.4 kW prototype resonant converter and its IH coil validate the proposed design.

• Journal of the Korean Society of Safety
• /
• v.3 no.1
• /
• pp.21-29
• /
• 1988

Conventional pwm switching power supply have the disadvantage some aspects of size, light weight, noise and system stability. High frequency Series Resonant Converter (SRC), described in this paper, almost improve above disadvantages. We use the state plane technique as analysis method. This technique is powerful tool which can clearly analyze the peak stress of the state variables inside the converter, Here, we can define each operation mode from frequency ratio Fsn, switching frequency to resonant frequency, and we analyze the output performance in each operation mode. To verify the theoretical analysis, we compose the actual converter, and the experimental results are compared with analysis.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.151-154
• /
• 1988

Quantum converters, a subset of resonant converters operating with optimal conditions are modeled. It is shown that series resonant converter(SRC) can be modeled as buck/boost converter with an equivalent inductor and parallel resonant converter(PRC) can be modeled as Cuk converter, with an equivalent capacitor. Also new resonant circuits with boost, buck-boost and Cuk converter characteristics are proposed. From these models, the quantum converters can be designed to be controlled with closed loop feedback, having many advantages such as low device switching stress, reliable high frequency operation and low EMI.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.1
• /
• pp.57-63
• /
• 2014

In this paper a bidirectional DC-DC converter is proposed for renewable energy systems, eco-friendly vehicles, energy storage systems, uninterruptible power supply(UPS) systems and battery test equipments. The two-stage bidirectional converter employing a fixed-frequency series loaded resonant converter is designed to be capable of operating under zero-current-switching turn on and turn off regardless of voltage and load variation, and hence its magnetic components and EMI filters can be optimized. And efficiencies and volumes of the two-stage bidirectional converters are compared according to configuration of isolated and non-isolated parts and a two-stage topology suitable for low voltage and high current applications is proposed. A 12kW(12V, 1000A) prototype of the proposed converter has been built and tested to verify the validity of the proposed operation.