• Journal of Sensor Science and Technology
• /
• v.14 no.2
• /
• pp.96-100
• /
• 2005

The planar Schottky diodes were fabricated and modeled to probe the device applicability of the cracked GaN epitaxial layer on a (111) silicon substrate. On the unintentionally n-doped GaN grown on silicon, we deposited Ti/Al/Ni/Au as the ohmic metal and Pt as the Schottky metal. The ohmic contact achieved a minimum contact resistivity of $5.51{\times}10.5{\Omega}{\cdot}cm^{2}$ after annealing in an $N_{2}$ ambient at $700^{\circ}C$ for 30 sec. The fabricated Schottky diode exhibited the barrier height of 0.7 eV and the ideality factor was 2.4, which are significantly lower than those parameters of crack free one. But in photoresponse measurement, the diode showed the peak responsivity of 0.097 A/W at 300 nm, the cutoff at 360 nm, and UV/visible rejection ratio of about $10^{2}$. The SPICE(Simulation Program with Integrated Circuit Emphasis) simulation with a proposed model, which was composed with one Pt/GaN diode and three parasitic diodes, showed good agreement with the experiment.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.975-978
• /
• 1999

The transmission line effects of IC interconnects have a substantial effect on a hish-speed VLSI circuit performance. The effective transmission lime parameters are changed with the increase of the operation frequency because of the skin of the skin effect, proximity effect, and silicon substrate. A new signal delay estimation methodology based on the RLC-distributed circuit model is presented ［2］. The methodology is demonstrated by using SPICE simulation and a high-frequency experiment technique.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.40 no.5
• /
• pp.531-539
• /
• 1991

We develop an analytical model of the static and the dynamic characteristics of amorphous silicon thin film transistors (a-Si TFTs) in order to incorporate into a widely used circuit simulator such as SPICE. The critical parameters considered in our analytical model of a-Si TFT are the power factor (XN) of saturation source-drain current and the effective channel length (L') at saturation region. The power factor, XN must not always obey so-called

• Journal of Sensor Science and Technology
• /
• v.23 no.4
• /
• pp.284-289
• /
• 2014

In this paper, modeling of a gate/body-tied (GBT) PMOSFET photodetector with built-in transfer gate is performed. It can control the photocurrent with a high-sensitivity. The GBT photodetector is a hybrid device consisted of a MOSFET, a lateral BJT, and a vertical BJT. This device allows for amplifying the photocurrent gain by $10^3$ due to the GBT structure. However, the operating parameters of this photodetector, including its photocurrent and transfer characteristics, were not known because modeling has not yet been performed. The sophisticated model of GBT photodetector using a process simulator is not compatible with circuit simulator. For this reason, we have performed SPICE modeling of the photodetector with reduced complexity using Cadence's Spectre program. The proposed modeling has been demonstrated by measuring fabricated chip by using 0.35 im 2-poly 4-metal standard CMOS technology.

• Journal of Korea Multimedia Society
• /
• v.3 no.5
• /
• pp.535-541
• /
• 2000

In this paper, we analyzed the characteristics of schottky junction to develop the voltage swing of ISL, and simulated the characteristics with the programs at this junctions. Simulation programs for analytic characteristics are the SUPREM V, SPICE, Medichi, Matlab. The schottky junction is rectifier contact between platinum silicide and silicon, the characteristics with programs has simulated the same conditions. The analytic parameters were the turn-on voltage, saturation current, ideality factor in forward bias, and has shown the results of breakdown voltage between actual characteristics and simulation characteristics in reverse bias. As a result, th forward turn-on voltage, reverse breakdown voltage, barrier height were decreased but saturation current and ideality factor were increased by substrates increased concentration variations.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.82-82
• /
• 2008

One-dimensional (1D) nanowires have been received much attention due to their potential for applications in various field. Recently some logic applications fabricated on various nanowires, such as ZnO, CdS, Si, are reported. These logic circuits, which consist of two- or three field effect transistors(FETs), are basic components of computation machine such as central process unit (CPU). FETs fabricated on nanowire generally have surrounded shapes of gate structure, which improve the device performance. Highly integrated circuits can also be achieved by fabricating on nano-scaled nanowires. But the numerical and SPICE simulation about the logic circuitry have never been reported and analyses of detailed parameters related to performance, such as channel doping, gate shapes, souce/drain contact and etc., were strongly needed. In our study, NAND and NOT logic circuits were simulated and characterized using 2- and 3-dimensional numerical simulation (SILVACO ATLAS) and built-in spice module(mixed mode).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.75-78
• /
• 1998

The SONOSFET Shows low operation voltage, high cell density, anti good endurance due to modified Fowler-Nordheim tunneling as memory charge injection method. In this paper, therefore, the NOR-type Flash EEPROM composed of SONOSFET, which has fast lead operation speed and Random Access characteristics, is proposed. An 8${\times}$8 bit NOR-type SONOSFET Flash EEPROM had been designed and its electrical characteristics were verified. Read/Write/Erase operations of it were verified with the spice parameters of SONOSFETs which had Oxide-Nitride-Oxide thickness of 65${\AA}$-165${\AA}$-35${\AA}$ and that of scaled down as 33${\AA}$-53${\AA}$-22${\AA}$, respectively. When the memory window of the scaled-down SONOSFET with 8V operation was similar to that of the SONOSFET with 13V operation, the Read operation delay times of the scaled-down SONOSFET were 25.4ns at erase state and 32.6ns at program state, respectively, and those of the SONOSFET were 23.5ns at erase state and 28.2ns at program state, respectively.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.34C no.6
• /
• pp.11-21
• /
• 1997

The delay models for CMOS invertr presented so far predicted the delay time quite accurately whens input transition-time is very small. But the problem that the accuracy is inclined to decrease becomes apparent as input transition tiem increases. In this paper, a delay model for CMOS inverter is presented, which accuractely predicts the delay time even though input transition-time increases. To inverter must be included in modeling process because the main reason of inaccuracy as input transition tiem is the leakage current through the complementary MOS. For efficient modeling, this paper first models the MOSes with simple I-V charcteristic, with which both the pMOS and the nMOS are considered easily in calculating the inverter delay times. This resulting model needs few parameters and re-models each MOS effectively and simply evaluates output voltage to predict delay time, delay values obtained from this effectively and simply evaluates output voltage to predict delay time, delay values obtained from this model have been found to be within about 5% error rate of the SPICE results. The calculation time to predict the delay time with the model from this paper has the speed of more than 70times as fast as to the SPICE.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.463-466
• /
• 2000

According to the development of the semiconductor micro device technology, IC chip trends the high integrated, low power tendency. Nowadays, it can be showed the tendency of single chip in system level. But in the system level, IC operates by multi power supply voltages. So, semiconductor process is necessary for these multi power operation. Therefore, in this paper, dual gate high voltage device that operate by multi power supply of 5V and 20V fabricated in the 0.5${\mu}{\textrm}{m}$ CMOS process technology and its electrical characteristics were analyzed. The result showed that the characteristics of the 5V device almost met with the SPICE simulation, the SPICE parameters are the same as the single 5V device process. And the characteristics of 20V device showed that gate length 3um device was available without degradation. Its current was 520uA/um, 350uA/um for NMOS, PMOS and the breakdown voltages were 25V, 28V.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.4
• /
• pp.685-695
• /
• 1997

In this paper, a new CMOS continuous-time fully-differential current-mode integrator is proposed as a basic building block of the low-voltage high frequency current-mode active filter. The proposed integrator is composed of the CMOS complementary circuit which can extend transconductance of an integrator. Therefore, the unity gain frequency which is determined by a small-signal transconductance and a MOSFET gate capacitance can be expanded by the complementary transconductance of the proposed integrator. And also the magnitude of pole and zero are increased. The unity gain frequency of the proposed integrator is increased about two times larger than that of the conventional continuous-time fully-differential integrator with NMOS-gm. These results are verified by the small signal analysis and the SPICE simulation. As an application circuit of the proposed fully-differential current-mode integrator, the three-pole Chebyshev lowpass filter is designed using 0.8.$\mu$m CMOS processing parameters. SPICE simulation predicts a 3-dB bandwidth of 148MHz and power dissipation of 4.3mW/pole for the three-pole filter with 3-V power supply.