• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.22 no.6
• /
• pp.223-229
• /
• 2023

This papart proposes single pole double throw (SPDT) switch with six-stage radial stub resonators in the 3.6~4.0 GHz band. The switch was simulated using ADS (Advanced Design Software), a design tool for the wireless communication circuits, and evaluated on a pcb substrate. The measurement results of the radial SPDT switch showed an average 90 dB isolation, and 1.5 dB insertion loss. This isolation characteristic was 20 dB superior to higher than those laboratory or commercial products reported thus far. The proposed SPDT switch is applicable to multi-band RF front-end systems, such as WiMAX, LTE/5G, Wi-Fi, and HyperLAN.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.1 s.343
• /
• pp.143-148
• /
• 2006

This paper presents a high isolation and power-handling single-pole double-throw(SPDT) switch for dual band wireless LAN applications. The switch circuit has asymmetric topology which uses stacked-gate to have high power-handling and isolation for the Tx path. The proposed SPDT switch has been designed with optimum gate-width, bias, and number of stacked-gate FET. This SPDT switch has been implemented with $0.25{\mu}m$ GaAs pHEMT process which has Gmmax of 500mS/mm and fmax of 150GHz. The designed SPDT switch has the measured insertion loss of better than 0.9dB and isolation of better than 40dB for the Tx path and 25dB for the Rx path and the high power handling capability with PldB of about 23dBm for control voltage of -3/0V. The fabricated SPDT switch chip size is $1.8mm{\times}1.8mm$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.10 s.101
• /
• pp.1003-1009
• /
• 2005

In this paper, small-size high-power single pole double throw(SPDT) switch with defected pound structure(DGS) is presented for wireless broadband internet application. To reduce the circuit size using slow-wave characteristic, the DGS is applied to ${\lambda}/4$ transmission line of the switch and the measured results are compared with them of conventional switch. To secure high degree of isolation, the switch with the DGS is composed of shunt-connected PIN diodes and shows insertion loss of 0.8 dB and isolation more than 50 dB at 2.3 GHz. The size of the switch is reduced about $50\%$ only with the DGS patterns while it has very similar performance to the conventional shunt-type switch.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.7 s.337
• /
• pp.57-62
• /
• 2005

This paper describes the design of a high performance microwave single pole double throw (SPDT) monolithic microwave integrated circuit switch using GaAs pHEMT process. The switch design proposes a novel coplanar waveguide (CPW) impedance transform network which results in the low insertion loss and high isolation by compensating for the FET parasitics to get the low on-resistance and low off-capacitance. The proposed switch has the measured isolation of better than 24 dB and insertion loss of less than 2.6 dB from 53 to 61 GHz. The chip is fabricated with the size of 2.2mm $\times$ 1.6 mm.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.8
• /
• pp.52-58
• /
• 2008

Ths paper describes the Dual-band switch which was proposed new structure that could improved the specification of broadband and designed by the optimized structure through simulation. The Dual-band switch with 2.4[GHz]/5.8[GHz] that can apply to 802.11a/b/g system that is commercialized present was studied to get a new structure with higher power, high isolation. The transmitter of switch was designed to operate a parallel switching element with stack structure of two FET. The receiver designed to have asymmetry structure that insert series FET in addition to basic serial/parallel FET. SPDT(Single Pole Double Throw) Tx/Rx FET switch is a device that can do switching from a port of input to two port of output. The fabricated SPDT switch has the characteristic of insertion loss of a below -3[dB] form DC to 6[GHz] and the isolation of a below -30D[dB](Rx mode).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.10A
• /
• pp.965-970
• /
• 2005

In this paper, SPDT Tx/Rx MMIC switch applicable to IEEE 802.11a WLAN systems is designed and fabricated using a specific designed epitaxial layered pHEMT wafer and ETRI's $0.5{\mu}m$ pHEMT switch process. The SPDT switch exhibits a low insertion loss of 0.68dB, high isolation of 35.64dB, return loss of 13.4dB, power transfer capability of 25dBm, and 3rd order intercept point of 42dBm at frequency of 5.8GHz and control voltage of 0/-3V. The comparison of the measured performances with commercial products based on the GaAs pHEMT technology for low voltage operating at ${\pm}$ 3V/0V shows that the return loss is somewhat inferior to the commercial products and insertion loss is compatible with each other however, isolation characteristics are much better than in conventional chips. Based on these performances, we can conclude that the developed SPDT switch MMIC has an enough potential for IEEE802.11a standard 5 GHz-band wireless LAN applications.

• Journal of the Korean Vacuum Society
• /
• v.14 no.4
• /
• pp.207-214
• /
• 2005

This paper presents a channel structure for promising high performance pseudomorphic high electron mobility transistor(pHEMT) switching device for design and fabricating of microwave control circuits, such as switches, phase shifters, attenuators, limiters, for application in personal mobile communication systems. Using the designed epitaxial channel layer structure and ETRI's $0.5\mu$m pHEMT switch process, single pole double throw (SPDT) Tx/Rx monolithic microwave integrated circuit (MMIC) switch was fabricated for 2.4 GHz and 5 GHz band wireless local area network (WLAN) systems. The SPDT switch exhibits a low insertion loss of 0.849 dB, high isolation of 32.638 dB, return loss of 11.006 dB, power transfer capability of 25dBm, and 3rd order intercept point of 42dBm at frequency of 5.8GHz and control voltage of 0/-3V These performances are enough for an application to 5 GHz band WLAN systems.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.4
• /
• pp.155-159
• /
• 2004

This paper describes the design and the simulation of a single pole double throw(SPDT) FET switch for wireless LAN(IEEE802.11a ＆ IEEE802.11b) applications using drain impedance transformation network with Microstrip transmission line. At the receiving path insertion losses were from 0.8(㏈) to 1.462(㏈) between 2(㎓) and 4(㎓), from l.26(㏈) to 2.3(㏈) between 4.7(㎓) and 6.7(㎓) and the isolations were under 30(㏈) between 2(㎓) and 6.7(㎓). At the transmitting path insertion loss were from 1.18(㏈) to 2.87(㏈) between 2(㎓) and 4(㎓) from 0.625(㏈) to 1.2(㏈) between 4.7(㎓) and 6.7(㎓) and the isolations were under 30(㏈) between 2(㎓) and 6.7(㎓).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.3A
• /
• pp.179-184
• /
• 2003

In this paper, an asymmetric topology of MMIC SPDT switch was proposed to increase the isolation in the receiving path and decrease the insertion loss with higher P1dB in the transmitting path for the ISM band. This SPDT switch was implemented with 0.5㎛ GaAs MESFETs processed by ETRI for the IDEC MPW project. For the receiving path the measured insertion losses were 1.518dB at 3GHz and 1.777dB at 5.75GHz and the isolations were 38.474dB at 3GHz and 29.125dB at 5.75GHz. For the transmitting path the insertion losses were 0.916dB at 3GHz and 1.162dB at 5.75GHz and the isolations were 23.259dB at 3GHz and 16.632dB at 5.75GHz. Compared to the symmetric topology the isolations of the receiving path for the asymmetric one were improved by 15.9dB at 3GHz and 11.9dB at 5.75GHz and its insertion loss was increased by about 0.6dB. In addition, P1dB of 21.5 dBm for the transmitting path was obtained, which is increased by 3.86dB compared to the symmetric one.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.362-370
• /
• 2010

In this paper, a compact RF Front-end module for Wireless Fidelity(Wi-Fi) and Worldwide Interoperability for Microwave Access(WiMAX) applications is realized by low temperature co-fired ceramic(LTCC) technology. The RF Front-end module is composed of three LTCC band-pass filters, a Film Bulk Acoustic Resonator(FBAR) filter, fully embedded matching circuits, an SPDT switch for mode selection, an SPDT switch for Tx/Rx selection, and an SP4T switch for band selection. The parasitic elements of 0.2~0.3 pF are generated by the structure of stacking in the top pad pattern for DC block capacitor of SPDT switch for mode selection. These kinds of parasitic elements break the matching characteristic, and thus, the overall electrical performance of the module is degraded. In order to compensate it, we insert a parallel lumped-element inductor on capacitor pad pattern for DC block, so that we obtain the optimized performance of the RF Front-end module. The fabricated RF front-end module has 12 layers including three inner grounds and it occupies less than $6.0mm{\times}6.0mm{\times}0.728mm$.