• Transactions of Materials Processing
• /
• v.20 no.6
• /
• pp.409-419
• /
• 2011

Membrane structures are widely used for LNG(Liquefied Natural Gas) storage tanks. This study presents a membrane structure based on the Mark-III type. For its development, a series of numerical simulation was conducted using ABAQUS and experimental investigation was carried out. The manufacturing process of the membrane was simulated. The thickness distribution predicted by the numerical approach agreed well with the experimental results.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.1
• /
• pp.281-287
• /
• 2011

GFRP rebars could be deteriorated by concrete alkalinity. This paper focuses on the investigation of durability of GFRP rebars with ribs exposed to alkaline environment of concrete. It has been reported that the milled E-glass fibers in the ribs of GFRP rebar can increase bond strength between GFRP rebars and the concrete. In this study, the effect of milled alkaline resistant glass fibers (milled AR glass) and milled E-glass in the ribs on the durability of GFRP rebar is investigated through ISS tests and moist absorption tests of the bare rebar. To accelerate the effect of the alkalinity, high temperature($40^{\circ}C$) was applied. According to the test results, mix ratio of milled glass fibers in the ribs by weight had significant effect on durability of GFRP rebars with ribs. It is because that the high mix ratio may leads more voids in the ribs due to lower workability and formability. On the other hand, changing fiber type in the ribs from E-glass to AR-glass had no improvements on ISS strength of the GFRP rebar. Therefore, it is found that determination of proper mix ratio of milled glass fiber in the mixture for the formation of the ribs of the GFRP rebar is important.

• Membrane Journal
• /
• v.7 no.2
• /
• pp.95-109
• /
• 1997

The effects of varing axial flow rate and solute concentration on the performance of both module sets made by different methods for active layer formation were compared and determined. All experiments were conducted simultaneously at the same transmembrane pressure and energy consumption per membrane area. In every comparative run between the presence of Dean vortices in a helical module and absence of such vortices in a linear module from the first module set, the solution fluxes and permeabilities were higher, and in some cases substantially higher for the vortex flow. With pure water, the permeabilities of both modules from the second module set were different and the flux in a linear module was 150% higher than in the helical module. This explained both module membranes were totally different.

• Journal of Power System Engineering
• /
• v.16 no.6
• /
• pp.52-58
• /
• 2012

Roll forming process is one of the most widely used processes in the world for forming metals such as a furniture drawer guide or an up and down slide guide. It can manufacture goods of the uniform cross section on a large scale throughout the continuous processing. In the domestic design and manufacture, roll forming process for production is taking most of the method of 2-point under rail slide. However, this method is vulnerable to the structural strength and stiffness is not suitable for high load conditions. Therefore, through systematic study of high load, low noise 3-point ball type of under rail slide its own design and manufacturing technology is the need to build. In this paper, to make center member of 3-point ball-type under rail slide for the refrigerator doors, the roll forming modeling and simulation are performed. Tensile test is performed about SCP-1 1/2H for determine the mechanical properties of materials. Modeling and simulation of roll forming is used MSC.MARC software of a dedicated analysis program used by rigid plastic finite element method. Interference between the roll and the final shape are predicted from the results of the simulation.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.27 no.2
• /
• pp.197-207
• /
• 2011

The study aimed at examining how different reline resins affect flexural strength and flexural modulus of denture base. A total of 80 specimens ($64{\times}10{\times}3.3$ mm, according to ISO 1567:1999) of heat-polymerized resin, 40 specimens for (Lucitone199(Dentsply Int., NewYork, USA), SR Ivocap(Ivoclar AG, Schaan, Liechtenstein)) respectively, were polymerized according to the manufacturer's instructions and divided into eight groups(n = 10). Control group specimens remained intact. Specimens in the other groups were abraded on both sides to 2 mm thickness, and were relined in 1.3 mm thickness with 3 types of resins (Lucitone199(Dentsply), SR Ivocap(Ivoclar), and Rebase II(Tokuyama Co., Ltd, Tokyo, Japan)). All specimens were preserved in distilled water at $37^{\circ}C$ for 50 hours, and then were subjected to flexural strength testing in a universal testing machine using 3-point loading. A crosshead speed of 5 mm/min was used, and the distance between the supports was 50 mm. Data analyses included one-way analysis of variance(ANOVA) and the Tukey Honestly Significant Difference test (p=.05). Both heat-polymerized resin groups and auto-polymerized resin groups showed statistically low flexural strength and flexural modulus than control groups. Specimens relined with Lucitone 199 showed significantly higher flexural strength and flexural modulus than those relined with SR-Ivocap. Specimens relined with auto-polymerized resin showed significantly lower flexural strength and flexural modulus than those relined with heat-polymerized resin. Relining with heat-polymerized resins showed superior mechanical properties to relining with an auto-polymerized resin. Relining with the same heat-polymerized resin as the denture base does not affect mechanical properties of a denture. Lucitone199 using a compression-mould technique resulted in the highest flexural strength.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2001.04a
• /
• pp.80-80
• /
• 2001

제지 공정의 효율적인 운영을 위한 수단으로 보류 및 탈수성의 분석은 매우 중요한 작 업 이 다. 보류 및 탈수 특성 을 평 가하기 위 하여 SR(Shopper-Riegler), CSF(Canadian S Standard Freeness tester) 그리고 원형 수초지기 등의 비난류 상태의 자연탈수 특성 평가 장치와 동적 조건의 감압식 탈수성 분석기 등이 사용되고 있다. 하지만 이것들은 제지 공정 에 보다 더 근접한 탈수 및 보류 특성을 평가하기에는 부족한 점이 있다. 특히 wet-end 첨 가제들의 효능을 보다 정확히 분석하는 것이 불가능하다. 이런 이유로 난류 발생과 감압 탈 수 둥을 유도한 탈수 특성 평가 장치 개발의 필요성이 커지고 있다. R RDA - HSF(Retention Drainage Analyzer- Handsheet Former)는 지료조성, 감압탈수 및 습지의 성형이 자동화되어 보류도와 탈수성, 종이지합 및 강도를 종합 평가 할 수 있는 새 로운 실험실용 초지기이다. 보다 현장에 가까운 초지 조건을 구현하기 위해서 지료의 농도 를 높이고 진공 탈수를 실시함에 따라 기존의 탈수성 분석기나 보류도 측정기의 단점을 보 완하게 되 었다. 본 연 구에 서 는 Canadian Standard Freeness test와 Dynamic Drainage Jar test 및 원 형 수초지기를 활용한 기존의 탈수성, 보류도 분석 결과와 RDA-HSF를 비교하여, 자연 탈수를 이용하는 기존의 탈수 및 보류 설비에 비해 현장 공정을 보다 현실적으로 재현할 수 있는 감압 탈수 초지 설비로서 RDA-HSF의 활용 가능성을 분석하였다. RDA-HSF를 활용한 실험실적 분석을 통해 현장의 상황올 유사하게 재현함에 따라 공정 운영 인자의 변화에 따른 제품의 품질 및 생산효율을 예측할 수 있게 된 바, 보다 효율적 인 공정 관리가 가능할 것으로 기대된다. 안료 입자의 경우 피인쇄체의 표면 공극을 채우고, 비히클의 경우 미세한 공극속으로 침투되어 경화됨으로써 피인쇄체가 지니고 있는 공극량을 감소시커 게 될 것이다. 그리고 피인쇄체의 각종 형태의 공극으로 침투된 잉크의 양에 반비례적으로 피인쇄체의 표변에 잉크가 잔류하게 될 것이다. 따라서 본 연구에서는 여러가지 안료를 사용하여 각각 다른 공극 특성을 지니는 도공지를 제조한 후 이들이 가지는 공극 특성과 잉크의 잔류 거동에 대해 고찰해 보고자 하였다.여 표면 유효층 일부만 오버레이시키며I 주조 및 단조가 불가능한 재료까지도 표면부에 오버레이 시킴으로 서 부품 및 설비의 제조에 있어 재료비의 절감과 제품의 수명이 획기적으로 개선될 수 있다. 그리고 최근에는 도금 빛 용사 둥과 같은 표면처리를 할 경우임의 소재 표면에 도금 및 용 사에 용이한 재료를 오버레이용접시킨 후 표면처리를 함으로써 보다 고품질의 표면층을 얻기위한 시도가 이루어지고 있다. 따라서 국내, 외의 오버레이 용접기술의 적용현황 및 대표적인 적용사례, 오버레이 용접기술 및 용접재료의 개발현황 둥을 중심으로 살펴봄으로서 아직 국내에서는 널리 알려지지 않은 본 기 술의 활용을 넓이고자 한다. within minimum time from beginning of the shutdown.및 12.36%, $101{\sim}200$일의 경우 12.78% 및 12.44%, 201일 이상의 경우 13.17% 및 11.30%로 201일 이상의 유기의 경우에만 대조구와 삭제 구간에 유의적인(p<0.05) 차이를 나타내었다.는 담수(淡水)에서 10%o의 해수(海水)로 이주된지 14일(日) 이후에 신장(腎臟)에서 수축된 것으로 나타났다. 30%o의 해수(海水)에 적응(適應)된 틸라피아의 평균 신사구체(腎絲球體)의 면적은 담수(淡水)에 적응된 개체의 면적보다 유의성있게 나타났다. 해수(海水)에 적응(適應

• Membrane Journal
• /
• v.25 no.5
• /
• pp.415-421
• /
• 2015

$SrCo_{0.8}Fe_{0.1}Nb_{0.1}O_{3-{\delta}}$ oxide was synthesized by solid state reaction method. Dense ceramic membrane was prepared using as-prepared powder by pressing and sintering at $1250^{\circ}C$. XRD result of membrane showed single perovskite structure. The oxygen permeability were measured under 0.21 atm of oxygen partial pressure ($P_{O_2}$) and between 800 and $950^{\circ}C$. The oxygen permeation flux of $SrCo_{0.8}Fe_{0.1}Nb_{0.1}O_{3-{\delta}}$ membrane was increased with the increasing temperature. The maximum oxygen permeation flux was $1.839mL/min{\cdot}cm^2$ at $950^{\circ}C$. Long period permeability experiment was carried out to confirm the phase stability and $CO_2$-tolerance of membrane containing Nb in the condition of air with $CO_2$ (500 ppm) as feed stream at $900^{\circ}C$. The phase stability and $CO_2$-tolerance of $SrCo_{0.8}Fe_{0.1}Nb_{0.1}O_{3-{\delta}}$ were investigated by XRD and TG analysis. The result of $SrCo_{0.8}Fe_{0.1}Nb_{0.1}O_{3-{\delta}}$ which exposed carbon dioxide for 100 hours indicated 8wt% of $SrCO_3$. But it was known that the level of $SrCO_3$ production dose not have a significant effect on oxygen permeability.

• Membrane Journal
• /
• v.6 no.3
• /
• pp.157-165
• /
• 1996

Polysulfone(PS) membranes were prepared from homogeneous PS solutions by the phase inversion technique. When propionic acid(PA) was added into a casting solution of n-methylpyrrolidone(NMP) and PS, precipitation rate of the solution film was accelerated. This kind of acceleration was consistent, even though a precipitating nonsolvent was changed from water to isopropanol. These phenomena were caused by decrease of nonsolvent tolerance in the casting solution due to addition of PA. PS powder was prepared by precipitation of a 3wt% solution in dimethylformamide(DMF) using ethanol as nonsolvent. Gas adsorption analysis of the powder showed that the capillary condensation sites were found in the powder structure. Membranes prepared from PS solution(15wt%) in NMP had the following characteristics of gas adsorption and water permeation. In gas adsorption analysis, the membrane precipitated using isopropanol showed low uptake of nitrogen gas and the capillary condensation sites were not found. On the contrary, a significant amount of the capillary condensation sites was found in the membrane coagulated by water, which was related to increase of nitrogen uptake. tn the membrane prepared froin the solution including PA, an increase of the Henry's law sites and the Langmuir sites was not found clearly. However, the capillary condensation sites were significantly increased, and the water transport also increased.