• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.723-726
• /
• 2001

The design of delivery system is one of the most important subject in injection molding. Delivery system is a channel to flow the polymer melt from the injection molding machine to the mold cavities and affect quality and productivity of the part. The synthesis of delivery system of injection molding has been done empirically, since it requires profound knowledge about the moldability and causal effects on the properties of the part, which are not available to designers through the current CAD systems. A knowledge-based CAD system is constructed by adding the knowledge module to an existing geometric modeler and contains knowledge to permit non-experts ad well as mold design experts to generate the acceptable geometries of gate and runner for injection molded parts.

• Tribology and Lubricants
• /
• 제35권1호
• /
• pp.44-51
• /
• 2019

The paper presents the rotordynamic performance measurements and model predictions of a fuel cell electric vehicle (FCEV) air compressor supported on gas foil bearings (GFBs). The rotor has an impeller on one end and a thrust runner on the other end. The front (impeller side) and rear (thrust side) gas foil journal bearings (GFJBs) are located between the impeller and thrust runner to support the radial loads, and a pair of gas foil thrust bearings are located on both sides of the thrust runner to support the axial loads. The test GFJBs have a partial arc shim foil installed between the top foil and bump strip layers to enhance hydrodynamic pressure generation. During the rotordynamic performance tests, two sets of orthogonally installed eddy-current displacement sensors measure the rotor radial motions at the rotor impeller and thrust ends. A series of speed-up and coast-down tests to 100k rpm demonstrates the dominant synchronous (1X) rotor responses to imbalance masses without noticeable subsynchronous motions, which indicates a rotordynamically stable rotor-GFB system. Finite element analysis of the rotor determines the rotor free-free (bending) natural modes and frequencies well beyond the maximum rotating frequency. The predicted damped natural frequencies and damping ratios of the rotor-GFB system reveal rotordynamic stability over the speeds of interest. The imbalance response predictions show that the predicted critical speeds and rotor amplitudes strongly agree with the test measurements, thus validating the developed rotordynamic model.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2001년도 유체기계 연구개발 발표회 논문집
• /
• pp.347-353
• /
• 2001

A combined cycle, 'HYBRID', is emerging as a new power generation technology that is particularly suitable for the distributed power generation system, with high energy efficiency and low pollutant emission. Currently micro gas turbines and fuel cells are attracting a lot of attention to meet the future needs in the distributed power generation market. This hybrid system may have every advantages of both systems because a gas turbine is synergistically combined with a fuel cell into a unique combined cycle. The hybrid system is believed to become a leading runner in the distributed power generation market. This paper introduces a current plan associated with the development of the hybrid system which consists of a micro gas turbine and a solid-oxide fuel cell(SOFC).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.628-632
• /
• 2002

Low voltage circuit breakers which interrupt rapidly and raise the reliability of power supply are widly used in power distribution systems. In the paper, it was investigated how much Interrupting capability was improved by correcting the shape of the contact system in molded case circuit breaker(below MCCB), especially arc runner. Prior to the interrupting testing, it was necessary for the optimum design to analyze electromagnetic forces on the contact system, generated by current and flux density. This paper presents both our compuational analysis and test results on contact system in MCCB

• International Journal of Fluid Machinery and Systems
• /
• 제2권2호
• /
• pp.102-109
• /
• 2009

A design optimization system for Francis turbine was developed. The system consists of design program and CFD solver. Flow passage shapes are optimized automatically by using the system with Multi-Objective Genetic Algorithm (MOGA). In this study, the system was applied to a high specific speed Francis turbine (nSP = 250m-kW). The runner profile and the draft tube shape were optimized to decrease hydraulic losses. As the results, it was shown that the turbine efficiency was improved in wide operating range, furthermore, the height of draft tube was reduced with the hydraulic performance kept.

• 소성∙가공
• /
• 제16권1호
• /
• pp.54-60
• /
• 2007

Optimum injection molding condition for a box mold was searched by the Response Surface Analysis(RSA) with the aid of process monitoring system(PMS). Process variables on the control panel of the injection molding machine such as barrel temperatures, screw speed profile, holding pressures, etc. cannot guarantee the uniformity of the material variables directly related with the state of the product in the mold cavity. In order to make sure the state of the resin in the cavity, pressures and temperatures in the cavity, runner and nozzle were monitored in the experiment with the PMS. To accomplish the consistency of the molding process, dependent variables such as the switchover point and holding time were searched with the PMS. With a proper objective function about deflection of the box-type product, the optimum injection molding condition was obtained.

• 한국유체기계학회 논문집
• /
• 제14권6호
• /
• pp.5-10
• /
• 2011

Recently, small hydropower attracts attention because of its renewable, clean and abundant energy resources to develop. Therefore, a tubular type hydro turbine is proposed for small hydropower in this study because the turbine has relatively simple structure and high possibility of applying to small hydropower. The purpose of this study is to investigate the performance characteristics of the turbine by field test. Field test iss conducted using one tubular turbine system as well as serial arrangement system by two tubular turbines taking into consideration of actual operation conditions. The results show that efficiency of test turbine changes considerably by the runner vane angle. Best efficiency of one turbine arrangement is higher than that of two turbine serial arrangement.

• 원예과학기술지
• /
• 제17권3호
• /
• pp.325-328
• /
• 1999

본 실험은 딸기의 촉성재배에서 일반적으로 사용되고 있는 수동식 야냉육묘시설의 온도와 일장조절이 어려운 단점을 보완하고자 온도와 일장이 자동조절 되는 자동화 시설 내에서 육묘하였을 때 화아분화의 진행정도와 묘소질의 변화, 정식후 수량에 미치는 영향을 구명하고자 수행하였다. 자동화 야냉처리는 수동식처리와 마찬가지로 20일간의 처리에 의해 화아분화 유기가 가능하였다. 처리 14일째에는 화아분화 초기단계로 진행되었으며 20일째에는 분화기까지 진행되었다. 자동화 야냉처리 동안 묘소질은 수동식 육묘장보다 중, 하단에서는 약간 도장하여 관부가 가늘어지는 경향을 보였으며 엽록소 함량의 증가와 증산량의 감소가 있었다. 그러나 화아분화 처리된 묘의 정식후 생육은 처리간에 큰 차이가 없었다. 조기수량이나 품질면에서도 수동식 야냉육묘 방법과 차이가 없어 온도와 일장의 자동조절 자동화 시설내에서 촉성재배 딸기육묘가 가능하였다.

• International Journal of Safety
• /
• 제9권2호
• /
• pp.22-28
• /
• 2010

This paper describes a web-based design review system as a knowledge management system relating reliability and safety system design. Since people's consciousness for safety and security become sensitive and increases the need of establishing a proactive prevention method for internal failures and relating risks in products. It also means that prevailing tacit knowledge in retired workers, in order to transform them to be easily used to support new system development, become more important. When considering safety and reliability design, at least two data sheet are necessary; Failure Modes and Effects Analyses (FMEA) and Risk Assessment (RA). These two data are practically made separately. However, it includes the concerns that a risk by failures during long-term use may not be noticed. To overcome this insufficiency, a support tool for integrating reliability evaluation and risk assessment data simultaneously is expected to be revealed. The authors have then developed a web-based design review system for reliability and safety system design. The system include various profitable functions; making FMEA and RA sheet, retrieving past data sheet for engineering change management and new product development and web-based discussion to increase the efficiency of discussion. The system is applied to one practical development works in order to demonstrate its effectiveness that is to be made clear by interviewing user's qualitative comment.

• 대한기계학회논문집A
• /
• 제39권1호
• /
• pp.111-115
• /
• 2015

핫 러너를 이용한 사출 공정에서는, 색교체가 중요한 문제이다. 이 연구는 열가소성 수지의 색교체 특성을 평가할 수 있는 방법을 제시하고자 한다. 캐필러리 다이를 이용하여 색교체도를 평가할 수 있는 방법을 고안하고 구현한다. 캐필러리 다이로부터의 토출물을 영상화하여, 회색음영으로 정량화하였다. 그 음영도를 기반으로 하여, 색교체도를 결정하였다. 주어진 온도와 토출 속도에서, 색교체도가 토출회수에 따라 변화하는 추이를 얻어 내고 분석하였다.