• 접착 및 계면
• /
• 제16권3호
• /
• pp.116-121
• /
• 2015

본 연구에서는 발수성 재료로 쓰이고 상대적으로 가격이 비싼 불소계 실란을 대체하기 위해 octadecyltrichlorosilane (OTS)을 사용하였다. 코팅층의 기계적 접착강도를 향상시키기 위해 무기바인더를 산 촉매 하에서 졸-겔 반응에 의해 분산시켜 합성하였다. 합성된 실리카 나노입자는 나노크기의 거칠기를 제공하기 때문에 초소수성을 쉽게 얻기 어려우므로 유기용매에 의한 입자의 응집을 유도하였다. 실리카 나노입자의 적절한 크기 선택에 따라 OTS를 사용해서 표면을 소수화 시킨 후 유기용매의 양이 증가함에 따라 초소수성의 표면을 얻었고 극도의 물 반발 거동이 zero sliding angle과 함께 관찰되었다. 이러한 초소수성은 용매와의 혼합과 상관없이 유전상수가 25보다 작은 값을 가졌으며 용매 내에서 입자의 응집을 통해 유도된 초소수성 표면을 제조하는 것이 저유전상수 값에 대한 지표가 되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.231.1-231.1
• /
• 2015

Surface energy, being an important material parameter to control its interactions with the other surfaces plays a key role in bio-related application. Carbon films are found very promising due to their characteristics such as wear and corrosion resistant, high hardness, inert, low resistivity and biocompatibility. The present work deals with the deposition of carbon films using unbalanced facing target magnetron sputtering technique. The discharge characteristics were studied using optical emission spectroscopy and correlated with the film properties. Surface energy was investigated through contact angle measurement. The ID/IG ratio as calculated from Raman spectroscopy data increases with the increase in power density due to the higher number of sp2 clusters embedded in the amorphous matrix. The deposited films were smooth and homogeneous as observed by Atomic force microscopy having RMS roughness in the range of 1.74 to 2.25 nm. It is observed that electrical resistivity and surface energy varies in direct proportionality with operating pressure and has inverse relation with power density. The surface energy results clearly exhibited that these films can have promising applications in cell cultivation.

• 한국세라믹학회지
• /
• 제43권2호
• /
• pp.85-91
• /
• 2006

Electron Beam Physical Vapor Deposition (EB-PVD) was applied to fabricate a thin film YSZ electrolyte with large area on the porous NiO-YSZ anode substrate. Microstructural and thermal stability of the as-deposited electrolyte film was investigated via SEM and XRD analysis. In order to obtain an optimized YSZ film with high stability, both temperature and surface roughness of substrate were varied. A structurally homogeneous YSZ film with large area of $12\times12\;cm^2$ and high thermal stability up to $900^{\circ}C$ was fabricated at the substrate temperature of $T_s/T_m$ higher than 0.4. The smoother surface was proved to give the better film quality. Precise control of heating and cooling rate of the anode substrate was necessary to obtain a very dense YSZ electrolyte with high thermal stability, which affords to survive after post heat treatment for fabrication a cathode layer on it as well as after long time operation of solid oxide fuel cell at high temperature.

• 대한토목학회논문집
• /
• 제33권5호
• /
• pp.1829-1840
• /
• 2013

수리구조물의 효과적 운영과 홍수기 피해저감을 위해서는 하천수리특성에 대한 적절한 이해가 필수적이기 때문에 본 연구에서는 낙동강 수계 금호강 유입지점 하류를 대상으로 준설 및 수리시설물 운영에 따른 수리특성 영향을 분석하였다. 수리특성 분석을 위해 HEC-RAS 모형을 이용하였으며, 부정류 흐름 해석을 통해 흐름의 천이를 반영하고 수리시설물 운영을 위한 다기능보 제원을 적용하였다. 조도계수와 조고값의 관계, 정류와 부정류 흐름해석, 사업 전과 후 하천 단면 그리고 다기능보 운영에 따른 하천 흐름에 대해 다각도로 연구를 하였다. 낙동강 수계 주요 관심구간을 중심으로 급격한 지형변화 및 수리구조물 운영에 의한 홍수에 대비하고 주요지점별 유량 전달에 의한 홍수파에 대해 분석된 자료는 합리적인 하천관리를 위한 기초자료로 활용될 수 있을 것이다.

• 펄프종이기술
• /
• 제48권1호
• /
• pp.27-33
• /
• 2016

This study was carried out in order to investigate the effect of binder properties in pre-coating layer on the characteristics of top-coating layer and print mottle of coated paper. Four different latices were used as a binder in pre-coating layer, and coating color prepared with a same formulation was applied for top-coating. The properties and print mottle of coated paper were evaluated. It was found that glass transition temperature (Tg) was the important factor to control the properties of pre- and top-coating layer. PPS roughness of coated paper was decreased and paper gloss was increased with applying binder which has lower Tg. Properties of top-coating layer were affected by the binder used in pre-coating layer. Print mottle of coated paper was improved with using binder which has lower Tg in pre-coating layer. These results indicate that final printability and properties of top-coating layer can be improved with using suitable binder in pre-coating layer.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 추계학술발표강연 및 논문개요집
• /
• pp.135-135
• /
• 2003

The fast evolution in the fold of optical communication systems demands powerful optical information treatment. These functions can be performed by integrated optical systems. A key component of such systems is erbium doped waveguide amplifier(EDWA). The intra 4f radiative transition of Er at 1.5 $\mu\textrm{m}$ is particularly interesting because this wavelength is standard in optical telecommunications. The fabrication of waveguide amplifier for integrated optics using sol-gel process has received an increasing attention. Potential advantage of lower cost by less capital equipment and easy processing makes this process an attractive alternatives to conventional technologies like flame hydrolysis deposition, ion exchange and chemical vapor deposition, etc. In addition, sol-gel process has been found to be extremely suitable for the control of composition and refractive index related directly with optical properties. The main drawback of such an amplifier with respect to the EDWA is the need for a much higher Er3+ concentration to compensate for the smaller interaction length. However, the high doping of Er might be resulted in the non-radiative relaxation by clustering of Er ions End co-operative upconversion. In order to solve this problem, we investigate the possibility of avoiding short Er-Er distances by encapsulation of Er3+ ions in hosts such as organic-inorganic hybrid materials. For inorganic-organic hybrid sols, methacryloxypropyltrimethoxysilane (MPTS), zirconyl chloride octahydrate and erbium(III) chloride hexahydrate were used as starting materials, followed by conventional sol-gel process. It was observed by TEM that nano sols having core/shell toplology were formed, depending on the mole ratio of Zr/Er. The surface roughness for the coatings on Si substrate was investigated by AFM as a function of Zr/Er ratio. The local environment and vibrational Properties of Er3+ ions were studied using Near-IR, FT-IR, and UV/Vis spectroscopy. Nano hybrid coatings derived from polymer and Er doped encapsulation Eave the good luminescence at 1.55$\mu\textrm{m}$.

• 대기
• /
• 제21권4호
• /
• pp.415-427
• /
• 2011

In this study, the impacts of land surface conditions, land cover (LC) map and leaf area index (LAI), on the short-range weather forecast over the East-Asian region were examined using Unified Model (UM) coupled with the MOSES 2.2 (Met-Office Surface Exchange Scheme). Four types of experiments were performed at 12-km horizontal resolution with 38 vertical layers for two months, July and August 2009 through consecutive reruns of 72-hour every 12 hours, 00 and 12 UTC. The control experiment (CTRL) uses the original IGBP (International Geosphere-Biosphere Programme) LC map and old MODIS (MODerate resolution Imaging Spectroradiometer) LAI, the new LAI experiment (NLAI) uses improved monthly MODIS LAI. The new LC experiment (NLCE) uses KLC_v2 (Kongju National Univ. land cover), and the new land surface experiment (NLSE) uses KLC_v2 and new LAI. The reduced albedo and increased roughness length over southern part of China caused by the increased broadleaf fraction resulted in increase of land surface temperature (LST), air temperature, and sensible heat flux (SHF). Whereas, the LST and SHF over south-eastern part of Russia is decreased by the decreased needleleaf fraction and increased albedo. The changed wind speed induced by the LC and LAI changes also contribute the LST distribution through the change of vertical mixing and advection. The improvement of LC and LAI data clearly reduced the systematic underestimation of air temperature over South Korea. Whereas, the impacts of LC and LAI conditions on the simulation skills of precipitation are not systematic. In general, the impacts of LC changes on the short range forecast are more significant than that of LAI changes.

• 한국자동차공학회논문집
• /
• 제15권5호
• /
• pp.9-16
• /
• 2007

Since the liquid phase LPG injection(LPLI) system has an advantage of higher power and lower emission characteristics than the mixer type fuel supply system, many studies and applications have been conducted. However, the heat extraction, due to the evaporation of liquid fuel, causes not only a dropping of LPG fuel but also icing phenomenon that is a frost of moisture in the air around the nozzle tip. Because both lead to a difficulty in the control of accurate air fuel ratio, it can result in poor engine performance and a large amount of HC emissions. The experimental investigation was carried out on the bench test rig in this study. It was found that n-butane, that has a relatively high boiling point($-0.5^{\circ}C$), was a main species of droplet composition and also found that the droplet problem was improved by the use of a large inner to outer bore ratio nozzle whose surface roughness is smooth. The icing phenomena were decreased when the an engine head temperature was increased, although a large amount of icing deposit was still observed in the case of $87^{\circ}C$. Also, it was observed that the icing phenomenon is improved by using anti-icing bushing.

• 한국콘텐츠학회:학술대회논문집
• /
• 한국콘텐츠학회 2009년도 춘계 종합학술대회 논문집
• /
• pp.437-441
• /
• 2009

현대사회는 하천에서부터 시작되었다고 할 정도로 우리 삶의 중심에 있는 자연의 중요한 일부라고 할 수 있다. 하천은 단순한 치수와 이수뿐만 아니라 다양한 자연 그대로의 환경적 잠재 기능을 복원하는 방향으로 전환되고 있다. 이러한 하천 복원의 필수적 요소는 식생이나 이것은 하천의 흐름저항을 크게 하여 홍수시 수위를 증가시키는 요인이 된다. 따라서 식생에 따른 조도계수의 변화와 흐름저항으로 인한 수리학적 특성을 이해하는 것은 하천복원에서 중요한 요소가 된다. 본 연구에서는 하천식생 복원모형에서의 홍수위 분석과 하상변동을 예측하고자 한다. 이를 위해 공주대교 상 하류 구간에 HEC-RAS와 RMA-2 모형을 적용하여 홍수위 분석을 실시함과 동시에 SED-2D 모형을 적용하여 하상변동을 예측하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.2170-2174
• /
• 2005

Selective Laser Sintering (SLS) is a useful rapid prototyping technique for the manufacture of three dimensional (3D) solid objects directly from a scanning data. A new approach called a Selective Multi-Laser Sintering (SMLS) system has been developed at Korea Institute Machinery & Materials (KIMM) as an industrial type SFFS. This SMLS machine is built with a frame, heaters, nitrogen supply part, laser system. This system uses the dual laser and 3D scanner made in $Solutionix^{TM}$ to improve the precision and speed for large objects. The three-dimensional solid objects are made of polyamide powder. The investigation on each part of SMLS system is performed to determine the proper theirs design and the effect of experimental parameters on making the 3D objects. The temperature of the system has a great influence on sintering the polymer. Because the stability of the powder temperature prevents the deformation of each layer, the controls of the temperature in both the system and the powders are very important during the process. Therefore, we simulated the temperature distribution of build room using the temperature analysis with ANSYS program. Selected radiant heater is used to raise temperature of powder to melting point temperature. The laser parameters such as scan spacing, scan speed, laser power and laser delay time affect the production the 3D objects too. The combination of the slow scan speed and the high laser power shows the good results without the layer curling. The work is under way to evaluate the effect of experimental parameters on process and to produce the various objects. We are going to experiment continuously to improve the size accuracy and surface roughness.