• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.10
• /
• pp.4569-4573
• /
• 2011

Resolver doesn't have a advantage to price in comparision with encorder. However, resolver is used to the case of detecting a absoluteness position and is used to a fine control in the place of having a stability by mechanic. The position by resolver and the method by speed detecting is applied by observer and have a part of processing analog signal. In this paper, we used the method which output signal of resolver is demodulated by cos and sin waveform and the demodulated analog signal is transmitted to controller. We designed the estimated on the program of a controller and observed the movement on the low speed.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.61 no.3
• /
• pp.111-115
• /
• 2012

Generally, brushless DC motor(BLDCM) driving system uses hall sensors or encoders as the mechanical position or speed sensor. It is necessary to achieve the informations of rotor position for driving trapezoidal type brushless DC motor without any position sensor. In this paper, the commutation signals are obtained without the motor neutral voltage, multistage analog filters, A/D converters, or the complex digital phase shift circuits which are indispensable in the conventional sensorless control algorithms. In the proposed method, in stead of detecting the zero crossing point of the nonexcited motor back electromagnetic force for the average motor terminal to neutral voltage, the commutation signal are extracted directly from the specific average line to line voltage with low-pass filter, adder and comparators circuit. In contrast to conventional methods, the neutral voltage is not need; therefore, the commutation signals are insensitive to the common mode noise. Moreover, the complex phase shift circuit can be eliminated. The effectiveness of the proposed method is verified through simulation results.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.23-27
• /
• 2004

Information of rotor position is necessary to drive Linear Switched Reluctance Motor(LSRM). Therefore, linear optical encoder is used to detect a mover position. Normally, since the price of encoder, which is used for linear motor is relatively higher than the one used for rotory motor and the cost of additional equipment increases with the length of motor. As a results, LSRM has a great part for the total cost. In this paper, as using reflective type photo-sensors, it replaced the expensive linear encoder.

• Journal of Power System Engineering
• /
• v.3 no.2
• /
• pp.64-69
• /
• 1999

The paper shows a result for development of BLDC motor drive by using a resolver as position detection sensor. The developed drive use a method detecting rotor position based on HSI interrupt function of microprocessor without a specialized counting circuit. The algorithm generating three-phase PWM wave to change switching voltage and current is realized based on single chip microprocessor. The PWM generating part and position counting circuit are realized by software technique without usage of conventional analogue circuit or object-oriented chips. So the drive system become compact. The effectiveness of the developed drive is verified by experimented results of speed response for step reference input.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1144-1145
• /
• 2007

This paper is investigated the sensorless drive for BLDC motor using microprocessor. Since the BLDC motor should be commutated according to a rotor position, the sensors are required to detect the position. But the sensors increase cost and volume, complicate the motor configuration, and do not operate properly in some operating environments such as high temperature conditions, so that the necessity of sensorless commutation algorithm is getting increased. This paper is proposed the method to drive BLDC motor without position-detecting sensor using Back EMF. Back EMF commutation method was implemented the sensorless drive system which could control the rotational speed and monitor the behavior of a motor.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.9
• /
• pp.1-7
• /
• 2014

Brushless Direct Current(BLDC) Motor is essential to measure a rotor position because of that this motor type needs to synchronize the rotor's position and changeover phase current instead of a brush and commutator used on the existing dc motor. Recently, many researches have studied on sensorless control drive for BLDC motor. The conventional control methods are a compensation value dq, Kalman filter, Fuzzy logic, Neurons neural network, and the like. These methods has difficulties of detecting BEMF accurately at low speed because of low BEMF voltage and switching noise. And also, the operation is long and complex. So, it is required a high-performance microprocessor. Therefore, it is not suitable for a small BLDC motor sensorless drive. This paper presents control methods suitable for economic small BLDC motor sensorless drive which are an improved design of the BEMF detection circuit, simplifying a complex algorithm and computation time reduction. The improved motor sensorless drive is verified stability and validity through being designed, manufactured and analyzed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.92-99
• /
• 2008

This paper describes an signal processing method for the hall sensorless position control of ETC control system using a BLDC motor. The proposed ETC control system, which is mainly consisted of a BLDC motor, a throttle plate, a return spring and reduction gear, has a position sensor with an analog voltage output on the throttle valve instead of BLDC motor for detecting rotor position of motor. So the additional commutation information is necessarily needed to control the mentioned ETC module. In order to estimate and determine the commutation state, it is proposed to properly manipulate the resolution of A/D converter considering the mechanical parameter, that is, the number of motor slot and the ratio of reduction gear. Through this method, the estimation of commutation state for operating the system is possible and the discrete signal for commutation is stably obtained. The validity of the method is examined through the experimental results.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.1
• /
• pp.50-56
• /
• 2005

This paper develops a sensorless BLDCM drive for frequently startup. The position information is based on detecting the zero-crossing point of the BEMF that can be directly obtained from the terminal voltage of the floating phase without voltage-dividing and filtering. As a result, this approach makes it possible to detect the rotor position over a wide speed range, especially at a lower speed. A fast startup procedure is also discussed because the induced BEMF signals are not present when motor is at rest. Experimental results shows that the schemes implemented are feasible and the performance achieved are satisfactory.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.2 no.2
• /
• pp.231-239
• /
• 1998

In this paper, we designed a current controlling servo system for speed control of a PMSM. In existing auto-tuning methods for PI controller parameters, the output response is delayed and the overshoot is generated. By solving these existing problems in this paper, a new PI auto-tuning method is applied to the speed controller for fast-response and reduced overshoot. PMSM servo systems offer a great advantage in unmanned factories where a great number of servo motors are employed, because of its easy maintenance characteristics and controllability. The implemented servo system is composed of absolute position detecting circuits of a rotor, a new auto-tuning PI control algorithm, a speed controller by using DSP, and power driving section. The proposed servo system is verified for it's practical availability by considering experimental results.

• Proceedings of the KIEE Conference
• /
• 2007.04a
• /
• pp.377-379
• /
• 2007

To reduce the chattering errors of reed switch sensors used for automatic remote measurement of water supply system, a reed switch sensor was analyzed and improved. The operation of reed switch sensors can be described as a mechanical contact by approximation of permanent magnet piece to generate an electrical pulse. The reed switch sensors are used in measurement application by detecting the rotational or translational displacement. To apply for flow measurement devices, the reed switch sensors should keep high reliability. They are applied for the electronic digital type of water flow meters. The reed switch sensor is just installed simply on the mechanical type flow meter. A small magnet is attached on a pointer of the water meter counter rotor. Inside the reed sensor, two steel leaf springs make mechanical contact and apart as rotation of flow meter counter. The counting electrical contact pulses can be converted as the water flow amount. The MCU sends the digital flow rate data to the server using the wireless communication network. But it occurs data difference or errors by chattering noise. The reed switch sensor contains chattering error by it self at the force equivalent position. The vibrations such as passing car near to the switch sensor installed location. In order to reduce chattering error, most system uses just software methods for example using filter and also statistical calibration methods. The chattering errors were reduced by changing leaf spring structure using mechanical hysteresis characteristics.