• The KSFM Journal of Fluid Machinery
• /
• v.5 no.1 s.14
• /
• pp.55-61
• /
• 2002

The feasibility of an oil-free, motor-driven, two-stage centrifugal compressor supported by air bump bearings is investigated. This centrifugal compressor is driven by a 75 kW motor at an operating speed of 39,000 RPM, and a pressure ratio of the compressor is set up to 4. The analysis is performed by using bearing equilibrium position, heaving stillness, Campbell diagram, unbalance response, and stability. It is demonstrated in this paper that air bump bearings can be adopted well to an oil-free, motor-driven, centrifugal compressor. Specially, Cu-coated bump bearings have enough damping force to reduce a synchronous unbalance for rigid modes of the two-stage compressor. Futhermore, this concept may be applied to the flexible rotor system such as high speed turbomachinery with a super critical speed.

• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.74-76
• /
• 2004

This paper deals with the analytical method to calculate the high temperature demagnetization characteristics of a high-speed machine with diametrically magnetized permanent magnet rotor. The equivalent magnetic circuit model is used to analyze the magnet operating point on high temperature condition. Agreements have been obtained between the results of the analytical model and finite-element analysis on prototype high-speed motors.

• Journal of the Korean Society of Safety
• /
• v.13 no.1
• /
• pp.54-63
• /
• 1998

This paper proposes a theoretical analysis of a closed loop adaptive speed control system for control the inverter driven permanent magnet synchronous motor(PMSM). This control system utilizes a mechanically sensorless state observer for the generation of all controller feedback information. The observer processes measurements of stator frame voltage and current to produce estimates of rotor position and speed and rotor frame currents. It is shown that the identity observer, when properly formulated, has the same linearized error dynamics as the extended kalman filter(EKF). Consequently, it is shown that the gains within the identity observer can be designed in a manner identical to that of the EKF. In this way, the designability of the nonlinear observer is assured, as is the optimality of its performance for small errors. A sequence of simulation are performed and they demonstrate the successful performance.

• Electrical & Electronic Materials
• /
• v.10 no.9
• /
• pp.889-894
• /
• 1997

A miniaturized wind-mill type ultrasonic motor which has diameter in 12.7 mm and thickness in 2.0mm using PMN-PZT piezoelectric ceramics was fabricated. The wind-mill type ultrasonic motors has only three plate and of two wind-mill shape slotted metal endcaps a rotor whose end is hollowed out so that its periphery fits with the shape of the stator and a bearing to guide the rotor. A Finite Element Analysis was carried out to obtain the endcaps behavior under a radial displacement change of piezoelectric disk and to optimize the structure of the number of slots. Increasing the applied voltage the revolution speed of ultrasonic motors was increased. The maximum speed of 700 rpm and the maximum torque of 0.22 nN·m of the wind-mill type ultrasonic motors were obtained.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.109-111
• /
• 2002

It requires to study on accurate control skill for the technical improvement of servo system require. It needs to study on brake that has constant-torque speed range as load. In this paper, braking torque of eddy current brake between electromagnet stator and rotating disk are analyzed. The torque-speed characteristics and proper disk construction are presented in here. From the computer simulation results, it was found that eddy current braking torque is linear or approximately constant over the desired speed range depending on the rotor material, disk construction, pole number and pole displacement of stator, these are confirmed by experimental results.

• Tribology and Lubricants
• /
• v.15 no.4
• /
• pp.304-313
• /
• 1999

High-speed rotors set a lot of high vibration and stability problems especially when the speed of rotation is going through the first or the second critical speed. The aim of this paper is to investigate the possibility of an active control of a rigid rotor with squeeze film damper which has a good configuration of easily controlled end seal clearances and/or adjustment of a feed pressure. A theoretical method is presented and some numerical results are compared with test measurements. Both results show that the vibration or bit sizes are decreased when the end seal gap decreases with constant supply pressure, and when the supply oil pressure increases with constant seal gap. The experimental results show also a pleasing similarity on both orbit sizes and their decrement ratio compared with theoretical analysis. The possibility of an active control with the squeeze film damper was verified by adjusting the seal gap and the supply pressure.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.8
• /
• pp.408-415
• /
• 2006

This paper deal with control and design of 50,000rpm class Active Magnetic Bearing(AMB) system for high speed precision motor. In the design of AMB system, the design parameters adopted high robust rotor shaft, Active Magnetic Bearing, sensor and control system. In the design of Magnetic Bearing, 2-D Finite Element Method(FEM) is used and transfer matrix method is using for rotor dynamics. The control accuracy of high speed AMB system is demonstrated by experimentations.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.10
• /
• pp.433-437
• /
• 2005

This paper studied Rotary type ultrasonic motor which has cross type stator. The stator consists of hollowed cross type metal which has four piezoelectric ceramics on the ends of cross bars. When two harmonic voltages which have 90$^{\circ}$ phase difference given to ceramics, the elliptical motion was generated in the inside tips. Inside tips are contact with rotor and these elliptical motions are rotate the rotor The finite element analysis was used to optimize the dimension and displacement of the stator. And the analyzed results were compared with the experimental results of the motor. As results, the speed and the torque of motor was increased by increasing width of the cross bar. And the speed and torque o( motor was not influenced to length of cross bar. The speed and torque was linearly increased by increasing voltage. The maximum torque was generated when the motor fabricated length of cross bar and width of ceramics in the ratio of 1:2.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2064-2066
• /
• 2002

This paper proposes Model Reference Adaptive Fuzzy System(MRAFS) using Fuzzy Logic Controller(FLC) as a adaptive laws in Model Reference Adaptive System(MRAS) in order to realize the speed-sensorless control of an induction motor. MRAFS estimates the speed of an induction motor with a rotor flux of a reference model and adjustable model in MRAS. Fuzzy logic controller reduces the error of the rotor flux between the reference model and the adjustable model using the error and the change of error as the input of FLC. The computer simulation is executed to verify the propriety and the effectiveness of the proposed system.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.887-888
• /
• 2006

Switched Reluctance Motor(SRM) is rotated by reluctance force generated between rotor pole and stator pole. So SRM must be switched by exciting current according to rotor position. but SRM takes the advantages of high speed driving and very simple structure. The single phase SRM can not be start by itself and torque ripple is generated more than multi-phase SRM. But mechanical structure and driver is simpler than multi-phase SRM. The single phase SRM driver is composed with the absolute encoder and DSP to control exciting section and current, and is supplied by constant voltage. So The paper is intend to measure the speed charactrer of double silent pole type SRM by using the unipolar driving curcuit.