• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.395-399
• /
• 2004

Four microalloyed steels containing B were investigated in terms of hardenability, mechanical properties and microstructure depending upon the cooling rates in order to develop the steel grade for the cold forged fasners. The alloy with the largest DI value among 4 alloys, which contains $0.12\%\;C,\;1.54\%\;Mn,\;0.65\%\;Cr,\;0.11\%V,\;0.040\%Ti\;and\;0.0033\%B$, showed the larest shift to the right hand side in the TTT diagram, implying the wide allowable cooling rate range subsequent to hot rolling in long bar processing, Mechanical tests indicated that yield strength are dependent upon the DI value in water quenched specimens but other properties showed almost the same values. In the same grade of steel, the increase in cooling rates causes the decrease in elongation but the increase in strength, reduction of area and Charpy impact values. Microstructural examination in steel grade with the larest DI values revealed martensitic structure In the water quenched state, a mixture of martensite and bainite in the oil quenched, and ferrite + pearlite in the air cooled and the forced air cooled but the latter showed finer microstructure.

• Journal of Welding and Joining
• /
• v.32 no.5
• /
• pp.21-25
• /
• 2014

Oil and gas fields were left unexploited which deemed too deep and sour. New developing markets are emerging in this part and pipe manufacturers need demanding requirements in the combination of sour service requirements with heavier wall thickness required to cope with increasing water depths. Whilst, the strength and fracture toughness needed to meet the strict requirements In order to deliver the optimum sour properties in the final pipe, attention needs to be paid to each stage throughout the process from steel making. The main key during steel making is strengthening, securing mechanical properties and suppression of center segregation by adding proper chemical elements and controlling water cooling and plate rolling. Additionally in welding, it is required to prevent HAZ softening by high heat input during welding of heavy thick pipes and hydrogen assisted cracking in high strength steels with hard phases. In this paper, we introduce markets of sour resistant linepipe steels and in response to this, have a look in the development trend of sour resistant linepipe steels and its sour characteristics in welded joints.

• Tribology and Lubricants
• /
• v.35 no.4
• /
• pp.237-243
• /
• 2019

Through this study, we investigate the effects of ultrasonic nanocrystal surface modification (UNSM) technology on the fatigue life of needle roller bearings. The fatigue life of untreated and UNSM-treated needle roller bearings is evaluated using a roller fatigue tester at various contact stress levels under oil-lubricated conditions. We can ascertain that the fatigue life of an UNSM-treated needle roller bearing was extended by approximately 34.3% in comparison with an untreated one, where the effectiveness of UNSM technology diminishes with increasing contact stress. The surface roughness and surface hardness of needle roller bearings before and after being treated by UNSM technology are compared and discussed to understand the role of UNSM technology in improving the fatigue life of needle roller bearings. In addition, a fractograph of the damaged bearings is observed using a scanning electron microscopy to shed light on the fracture mechanisms of bearings under different contact stress levels. We can therefore conclude that the application of UNSM technology to the needle roller bearings improves the fatigue life by reducing the friction coefficient and increasing the wear resistance; this may be attributed to a reduction in surface roughness from 0.5 to $0.149{\mu}m$ and an increase in surface hardness from 58 to 62 HRc.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.7
• /
• pp.635-642
• /
• 2014

The large volume multi-tasking vertical lathe was developed for machining the bearing parts for a wind power generator. Although the machined part is large in size high precision tolerances are required recently. One of the most important components to achieve this mission is the rotating table which holds and supports the part to be machined. The oil hydrostatic bearing is adopted for the thrust bearing and the rolling bearing for the radial bearing. In this article experimental performance evaluation and its analysis results are presented. The rotational accuracy of the table is assessed and the frequency domain analysis for the structural loop is performed. And in order to evaluate the structural characteristic of table the moment load experiment is performed. The rotational error motion is measured as below 10 ${\mu}m$ for the radial and axial direction and 22,800 Nm/arcsec of moment stiffness is achieved for the rotary table.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.4
• /
• pp.82-88
• /
• 2012

The usage of recycling agent is the most effective way of enhancing the performance of recycled asphalt pavement. Generally, many countries accepted these recycling agents retarding the various types of cracks resulted in binder aging. Contrary to such general tendency, recycling agents are used as very small amount in domestic recycling plant. The main reason of this is relatively high price of recycling agent. Even though agent price is high, agent can be a effective and economical way of alternative in asphalt recycling. In this study, penetration and softning point test performed by using RTFO(Rolling Thin Film Oven) aged binder. And, PG(Performance Grade) at high temperature, fatigue and MSCR(Multi Stress Creep and Recovery) tests exercised. The oil type agent is worked well to retrieving target penetration number. In PG test, $G^*/sin{\delta}$ of agents identically showed high value and polymer type agent is good at recovery value.

• Journal of the Korean Society of Industry Convergence
• /
• v.9 no.1
• /
• pp.51-59
• /
• 2006

The study is diagnosis about fatigue failure phenomenon of heating coil spring (sup9) and heat treatment method that is used to crusher. Because more than 80~90% of damage announcement of breakdown of machine and construction is been caused in fatigue present state, fatigue failure became important leading person at design. Calculated design load is imposed repeatedly that fatigue breakdown is safe. Is phenomenon that change load is imposed in the construction continuously. Used coil spring applies heat 30minute by Quenching temperature $860^{\circ}C$ if see manufacturing process and temperature of gasoline of $50^{\circ}C$ keep after quench that know tempering a $460^{\circ}C$ 90minute a product be. If doto apply heat $950^{\circ}C$ material at rolling process historically before quenching, austenite formation clay pipe being done AGS(Austenite Grain Size) by 2.5~4 become. Apply heat quenching 30minute by $820^{\circ}C$ by improvement method and after quench that keep $50^{\circ}C$ in oil tempering if do $450^{\circ}C$, 90minute spring ideal formation sorbite formation of the river form and condition that satisfy most more than AGS 7 appeared. Also, we can secure authoritativeness through MT since shot peening processing.

• Tribology and Lubricants
• /
• v.33 no.3
• /
• pp.119-125
• /
• 2017

In this study, we perform a numerical analysis to predict the film thickness and lubrication regions for a thrust ball bearing under different operating conditions. Film thinning and replenishment affect the film thickness in starved lubrication. As the inlet meniscus position is brought to the edge of the Hertz contact, the thin film thickness is calculated as starved equation. We use a film replenishment model to determine the recovery film thickness between rolling elements. We use a hydrodynamic model to describe film recovery, that results from the effects of surface tension. In this model, we consider the surface tension gradient in fluid depression as the driving force for fluid recovery. We use Fourier transform method to determine the time-dependent depth of depressed oil. We calculate the change in the central film thickness graphically by using the recovery equation in starved elastohydrodynamic lubrication(EHL) under operating conditions that include numbers of balls, sliding velocity, applied force, and ambient film thickness. We evaluate the degree of starvation by using the distance from the center of the contact area to the meniscus position. Parched lubrication, a phenomenon where the film thickness decreases consistently, occurs at the severe condition. We determine optimal values with respect to the numbers of balls, and sliding velocity. The investigation can contribute to the design operating conditions for proper lubrication.

• Journal of Veterinary Clinics
• /
• v.32 no.4
• /
• pp.374-379
• /
• 2015

A 10-year-old gelding Warmblood weighing 560 kg was referred to J&C Equine Hospital with the history of hyperpnea, depression, pawing, and rolling for 7 hours. According to the results of clinical and ultrasound examination, it was considered that intestines were distended with thickened wall. The horse had been treated with lactated Ringers' solution (14 L, IV), flunixin meglumine (1.1 mg/kg, IV), and mineral oil (1 L, PO), but he did not show any responses to those treatments. Exploratory laparotomy was performed and identified incarcerated small intestine through the epiploic foramen. The horse received resection and anastomosis of the entrapped small intestine. After surgery, the horse was treated with intensive postoperative care of fluid therapy (5 L with 20 mEq/L KCl, every 2 hours), flunixin meglumine (1.1 mg/kg, IV, sid), antibiotics (penicillin 22,000 IU/kg, IV, qid and gentamicin 6.6 mg/kg, IV, sid), lidocaine constant rate infusion (bolus 1.3 mg/kg over 15 minutes then 0.05 mg/kg/minute), common nutritional supplements, nasogastric intubation every 2 hours and trunk bandage. Postoperative feeding program had started with small amount of hay every 4 hours and gradually increased to normal amount till 5 days. At 77 days after surgery, he showed sudden outbreak of colic and was euthanized. The causes of colic were small intestinal strangulation by passing through the mesenteric rents and postoperative adhesion between small intestines. According to the results, it is recommended to perform perioperative intensive care of horse with colic and to use several methods to prevent adhesions during abdominal surgery of horses.

• Journal of Korea Port Economic Association
• /
• v.38 no.2
• /
• pp.49-67
• /
• 2022

This study applied the method of Diebold and Yilmaz (2012, 2014, 2016) to analyze the connectedness between the Freight Index (BDI, BDTI, BCTI), energy price(oil, natural gas, coal), and grain price(soybean, corn, wheat) from July 19, 2007 to March 31, 2022. The main analysis results of this paper are as follows. First, according to the network analysis results, the total connectedness was measured to be 20.43% for the entire analysis period, indicating that there was a low correlation between the freight index and the commodity price. In addition, looking at the directional results, the variable with the greatest effects was corn, and conversely, the variable with the lowest effects BDI. When classified by events, BCTI was found to play a major role only during the COVID-19 period. Second, according to the results of the rolling-sample analysis, the total connectedness be found to be highly correlated with changes in economic conditions such as the financial crisis, trade war, and COVID-19 when specific events occurred.