• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2002.11a
• /
• pp.81-90
• /
• 2002

Air entrainment of a winding roll with a nip roller was studied numerically. The amount of air entrainment between two rotating rollers was obtained by solving lubrication equation, Reynolds equation, which neglect the existence of a web. However, the numerical model of this study included the web existence, therefore it considered the two lubricating air films between a winding roll and a web and also between a nip roller and the web. The pressure profiles and gap profiles of the two films were obtained by solving lubrication equation for the two air films and force balance equation of the web. Ballooning phenomenon was examined in terms of nip force, wrap angle, web stiffness, web speed, and web tension. This ballooning phenomenon caused by the back flow of the air film blocked by the nip roller. Air entrainment of the two numerical models was compared.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.5
• /
• pp.31-46
• /
• 1999

A drying paper strives to shrink due to the shrinkage of the individual paper fibres. Laboratory results show that a reduction of the shrinkage or an imposed stretch leads to a large increase in tensile stiffness and a large decrease in strain at break. In c cylinder drying section the water in the web is repeatedly heated on the drying cylinder and evaporated in the free draw. To evaluate the drying process regarding influence on paper properties these sub-processes, or drying phases, have to be studied separately. The effect of the conditions on the drying cylinder and on the VacRoll is investigated in pilot trails. Both the fabric tension on the drying cylinder and on the VacRoll reduces the shrinkage of the paper. The laboratory results are used as input to a numerical simulation of the conditions in the free draw. If the web width is increased or the length of the free draw is reduced the mean shrinkage of the paper web is reduced . However, the difference in shrinkage between the middle and the edge of the web is increased.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.893-900
• /
• 1994

In this study, workspace analysis has been performed for a Clemens Coupling type parallel robotic wrist with four degrees of freedom such as three angular degrees of freedom and 1 plunge motion. Because of plunge motion, this mechanism has no singular point that the general roll-pitch-roll mechanisms have. Also, proposed mechanism performs larger load, faster motion, with less weight and has better structural characteristics such as higher stiffness and strength to weight ratio compared with serial type mechanisms. As a basic step for position control, the closed form solution of forward and inverse kinematics are proposed and workspace is analyzed and plotted by applying triangle tracer method for workspace boundary tracing.

• Journal of Advanced Marine Engineering and Technology
• /
• v.14 no.2
• /
• pp.35-47
• /
• 1990

The natural frequency of lateral vibration for ship's propulsion shafting tends to become lower as the relative stiffness of supproted system of the propulsion shafting decreases and the weight of shafting increases. Especially, the propulsion shafting of high-power ships such as car ferries, roll-on/roll-off, and container ships are susceptible to lateral vibration for their resonant speeds are happened to be in ordinary operating speed ranges. So far, many papers on the lateral vibration of ship's propulsion shaftings are published but they treated mainly special cases and not explained explicitly the calculation process. In this paper, the calculation processes of undamped and also forced damped lateral vibration by the transfer matrix method are presented and the calculation programs are developed. With the developed computer programs, a ship's propulsion shafting which was introduced on the published paper is analyzed for its lateral vibration and also the lateral vibration of the main drive shaft for a lathe is calculated to show the availiability of developed computer programs.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.100-105
• /
• 2002

In order to investigate how the chassis frame stiffness including body structure affects vehicle handling characteristics, in this paper, objective test evaluations such as steady state circle maneuvering test and pulse input transient test are performed. The basic steer characteristics can be obtained from stability factor and 4 parameter method is used to evaluate vehicle handling characteristics between original vehicle and the other with reinforced chassis. The result shows that vehicle with reinforced chassis has advantages in handling characteristics.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.3
• /
• pp.229-234
• /
• 2010

This paper presents the analysis of pitch static attitude(PSA) in thermally assisted magnetic recording(TAMR) suspension. The TAMR suspension using an optical fiber has high stiffness such as vertical, pitch and roll. Therefore, P-torque is greatly increased by the optical fiber. Also, flying height(FH) of the slider with TAMR suspension can be largely changed by PSA. In this paper, we focus on the FH by PSA of TAMR suspension. The FH is investigated using various PSA and proper PSA is proposed.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.12
• /
• pp.1303-1312
• /
• 2013

We report an ultra-precision lathe designed to machine micron-scale features on a large-area roll mold. The lathe can machine rolls up to 600 mm in diameter and 2,500 mm in length. All axes use hydrostatic oil bearings to exploit the high-precision, stiffness, and damping characteristics. The headstock spindle and rotary tooling table are driven by frameless direct drive motors, while coreless linear motors are used for the two linear axes. Finite element method modeling reveals that the effects of structural deformation on the machining accuracy are less than $1{\mu}m$. The results of thermal testing show that the maximum temperature rise at the spindle outer surface is approximately $0.5^{\circ}C$. Finally, performance evaluations of the error motion, micro-positioning capability, and fine-pitch machining demonstrate that the lathe is capable of producing optical-quality surfaces with micron-scale patterns with feature sizes as small as $20{\mu}m$ on a large-area roll mold.

• Structural Engineering and Mechanics
• /
• v.48 no.4
• /
• pp.479-500
• /
• 2013

This paper presents the experimental as well as analytical study conducted on layer-bonded scrap tire rubber pad (STRP) isolators to develop low-cost seismic isolators applicable to structures in developing countries. The STRP specimen samples were produced by stacking the STRP layers one on top of another with the application of adhesive. In unbonded application, the STRP bearings were placed between the substructure and superstructure without fastening between the contact surfaces which allows roll-off of the contact supports. The vertical compression and horizontal shear tests were conducted with varying axial loads. These results were used to compute the different mechanical properties of the STRP isolators including vertical stiffness, horizontal effective stiffness, average horizontal stiffness and effective damping ratios. The load-displacement relationships of STRP isolators obtained by experimental and finite element analysis results were found to be in close agreement. The tested STRP samples show energy dissipation capacity considerably greater than the natural rubber bearings. The layer-bonded STRP isolators serve positive incremental force resisting capacity up to the shear strain level of 150%.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1561-1569
• /
• 2000

Flying attitudes of the slider, which are flying height, pitch and roll, are affected by the air flow velocity, the skew angle, and the manufacturing tolerances. Traditional designs of the air bearing surface have considered only the flying performances for the variations in the air flow velocity and the skew angle, which are determined by the radial position. In this study, we present the new shape design of the air bearing surface by considering the track seek performance and the air bearing stiffness as well as the traditional design requirements. The optimization technique is used to improve the dynamic characteristics and operating performance of the newly proposed air bearing surface shape design further. The optimized configuration is obtained automatically and the optimally designed sliders show the enhanced flying and dynamic characteristics.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.197-204
• /
• 2003

This paper develops a computer model for estimating the handling of a cabover type large-sized truck. The truck is composed of front and rear suspension systems, a frame, a cab, and ten tires. The computer model is developed using ADAMS. A shock absorber, a rubber bush, and a leaf spring aunt a lot on the dynamic characteristic of the vehicle. Their stiffness and damping coefficient are measured and used as input data of the computer model. Leaf springs in the front and rear suspension systems are modeled by dividing them three links and joining them with joints. To improve the reliability of the developed computer model, the frame is considered as a flexible body. Thus, the frame is modeled by finite elements using MSC/PATRAN. A mode analysis is performed with the frame model using MSC/NASTRAN in order to link the frame model to the computer model. To verify the reliability of the developed computer model, a double lane change test is performed with an actual vehicle. In the double lane change, lateral acceleration, yaw rate, and roll angle are measured. Those test results are compared with the simulation results.