• Journal of Fisheries and Marine Sciences Education
• /
• v.12 no.2
• /
• pp.199-212
• /
• 2000

It is very important to investigate the hull response of a fishing vessel in the sea to ensure the safe navigation and fishing operation in rough sea by preserving excellent sea keeping qualities. For this purpose, the author measured various responses of three stem trawlers in waves using real sea experimental measuring system. The author analyzed the experimental data using the statistical and spectral analyzing method to get the characteristics of the motion responses of the vessels according to the wave height and the ship's speed. The results obtained can be summarized as follows ; (1) Rather higher response of the pitch motion due to the wave height appeared in the head sea and the bow sea than any other wave direction without relevance to ship's size. In case of the roll motion, the beam sea and the quartering sea have a high response value. The period of peak of the pitch motion and the roll motion according to the wave height in each vessel has almost same value respectively. (2) The change of response of the pitch motions deeply depend on the ship's speed in the head sea and the bow sea, but not in the other wave direction. (3) The change of response of the roll motions in the beam sea, the quartering sea and the following sea are affected by the influence of the ship's speed in 5k't to 8k't, but not related to the ship's speed in out of that range.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.21 no.3
• /
• pp.353-358
• /
• 2011

This paper presents a virtual-legged walking model for bipedal robots and analyzes its fundamental RPY(Roll, Pitch, and Yaw) motion effects by simulation. For the purpose of identifying the motion effects of the bipedal walking, we assign some arbitrary trajectories both at the center of mass and at the center of pressure of the robot based on human walking. And then we verify the major moments to the roll, pitch, and yaw directions of the robot. As a result, it is shown that those motions are natural in the process of bipedal walking and they are deeply dependent on the step distance, the vertical level of the center of mass, and the acceleration of the robot. The importance of trajectory planning for the footstep location during a bipedal walking is finally addressed in terms of balance.

• The Journal of Korean Society for Radiation Therapy
• /
• v.30 no.1_2
• /
• pp.201-208
• /
• 2018

Purpose : The purpose of this study is to compare and analyze the set-up errors using the Combine IGRT with ExacTrac and CBCT phased in the treatment of Stereotatic Body Radiotherapy. Methods and materials : Patient who were treated Stereotatic Body Radiotherapy in the ulsan university hospital from May 2014 to november 2017 were classified as treatment area three brain, nine spine, three pelvis. First using ExacTrac Set-up error calibrated direction of Lateral(Lat), Longitudinal(Lng), Vertical(Vrt), Roll, Pitch, Yaw, after applied ExacTrac moving data in addition to use CBCT and set-up error calibrated direction of Lat, Lng, Vrt, Rotation(Rtn). Results : When using ExacTrac, the error in the brain region is Lat $0.18{\pm}0.25cm$, Lng $0.23{\pm}0.04cm$, Vrt $0.30{\pm}0.36cm$, Roll $0.36{\pm}0.21^{\circ}$, Pitch $1.72{\pm}0.62^{\circ}$, Yaw $1.80{\pm}1.21^{\circ}$, spine Lat $0.21{\pm}0.24cm$, Lng $0.27{\pm}0.36cm$, Vrt $0.26{\pm}0.42cm$, Roll $1.01{\pm}1.17^{\circ}$, Pitch $0.66{\pm}0.45^{\circ}$, Yaw $0.71{\pm}0.58^{\circ}$, pelvis Lat $0.20{\pm}0.16cm$, Lng $0.24{\pm}0.29cm$, Vrt $0.28{\pm}0.29cm$, Roll $0.83{\pm}0.21^{\circ}$, Pitch $0.57{\pm}0.45^{\circ}$, Yaw $0.52{\pm}0.27^{\circ}$ When CBCT is performed after the couch movement, the error in brain region is Lat $0.06{\pm}0.05cm$, Lng $0.07{\pm}0.06cm$, Vrt $0.00{\pm}0.00cm$, Rtn $0.0{\pm}0.0^{\circ}$, spine Lat $0.06{\pm}0.04cm$, Lng $0.16{\pm}0.30cm$, Vrt $0.08{\pm}0.08cm$, Rtn $0.00{\pm}0.00^{\circ}$, pelvis Lat $0.06{\pm}0.07cm$, Lng $0.04{\pm}0.05cm$, Vrt $0.06{\pm}0.04cm$, Rtn $0.0{\pm}0.0^{\circ}$. Conclusion : Combine IGRT with ExacTrac in addition to CBCT during Stereotatic Body Radiotherapy showed that it was possible to reduce the set-up error of patients compared to single ExacTrac. However, the application of Combine IGRT increases patient set-up verification time and absorption dose in the body for image acquisition. Therefore, depending on the patient's situation that using Combine IGRT to reduce the patient's set-up error can increase the radiation treatment effectiveness.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.159-164
• /
• 1992

In this paper, the complex nonlinear dynamics of a satellite is obtained. And it is shown that several limitations exist when the magnetorquer is used as an active actuator to attitude control. Such limitations cause a delayed convergence of pitch and roll angle. The simulation results insure that the roll angle bias is dependent on the z axis spin rate. And a heuristic algorithm is applied to control the attitude libration through the computer simulations.

• Progress in Medical Physics
• /
• v.26 no.1
• /
• pp.6-11
• /
• 2015

The purpose of this study was to analyze the rotational errors of roll, pitch, and yaw in the whole breast cancer treated by the three-dimensional radiation therapy (3D-CRT) using TomoDirect (TD). Twenty-patient previously treated with TD 3D-CRT was selected. We performed a retrospective clinical analysis based on 80 images of megavoltage computed tomography (MVCT) including the systematic and random variation with patient setup errors and treatment setup margin (mm). In addition, a rotational error (degree) for each patient was analyzed using the automatic image registration. The treatment margin of X, Y, and Z directions were 4.2 mm, 6.2 mm, and 6.4 mm, respectively. The mean value of the rotational error for roll, pitch, and yaw were $0.3^{\circ}$, $0.5^{\circ}$, $0.1^{\circ}$, and all of systematic and random error was within $1.0^{\circ}$. The errors of patient positioning with the Y and Z directions have generally been mainly higher than the X direction. The percentage in treatment fractions in less than $2^{\circ}$ at roll, pitch, and yaw are 95.1%, 98.8%, and 97.5%, respectively. However, the edge of upper and lower (i.e., bottom) based on the center of therapy region (point) will quite a possibility that it is expected to twist even longer as the length of treatment region. The patient-specific characters should be considered for the accuracy and reproducibility of treatment and it is necessary to confirm periodically the rotational errors, including patient repositioning and repeating MVCT scan.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.40 no.4
• /
• pp.311-318
• /
• 2004

It is very important for the safe navigation and fishing operation to ensure the hull response of a fishing vessel in rough seas. This is an experimental study on the dynamical characteristics of ship's motion during operating job and sailing in the real sea. The experiments were carried out on the small stern trawler in operating job and sailing, and then the ship's roll and pitch motion were simultaneously recorded by P/C according to the wave directions. From these data, the statistical properties and power spectra were obtained and the analysis of ship's motions in the both case were made. The results obtained are summarized follows : (1) The amplitudes of pitch motion don't appear a big different between trawl job and sailing, but at bow seas, its in sailing have a tendency to increase more than in trawl job. The amplitudes of roll motion appear a bog different between trawl job and sailing, but at beam sea, that slightly decreasing tendency. (2) The peak period of pitch motion in trawl job and sailing change, but that of roll motion don't change according to the direction of waves. (3) The warp tention cause the motion of hull to be reduce, if the tention of each side have a ballance.

• Journal of Navigation and Port Research
• /
• v.48 no.3
• /
• pp.155-163
• /
• 2024

As the demand for reducing carbon emissions increases, efforts to reduce the usage of fossil fuels and research on renewable energy are also increasing. Among the various renewable energy harvesting techniques, the floating offshore wind turbine has several advantages. Compared to other technologies, it has fewer installation limitations due to interference with human activity. Additionally, a large wind turbine farm can be constructed in the open ocean. Therefore, it is important to conduct motion analysis of floating offshore wind turbines in waves during the initial stage of conceptual design. In this study, a frequency motion analysis was conducted on a semi-submersible type floating offshore wind turbine. The analysis focused on the effects of varying trim on the motion characteristics. Specifically, motion response analysis was performed on heave, roll, and pitch. Natural period analysis confirmed that changing the trim angle did not significantly affect the heave and pitch motions, but it did have a regular impact on the roll motion.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.11
• /
• pp.1184-1191
• /
• 2009

A bearingless linear motor(BLLM) which consists of two stators and a common mover is able to levitate and move its mover without any linear bearing or even additive windings. In the previous study, BLLM was actively controlled on the translation and pitch motion, while the roll motion is passively stable. In order to control the roll motion, this paper suggests adding active magnetic bearings(AMBs) at bottom of the mover in BLLM. The AMBs control the roll motion and also partially supports the weight of the mover. In this paper, magnetic forces generated by the AMBs are estimated by using an FEM model. Based on the analysis results, the bias current of the AMBs is determined and a PD controller is designed. Through an experimental levitation test, it was verified that roll motion is well controlled by AMB during levitation.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.3
• /
• pp.229-234
• /
• 2010

This paper presents the analysis of pitch static attitude(PSA) in thermally assisted magnetic recording(TAMR) suspension. The TAMR suspension using an optical fiber has high stiffness such as vertical, pitch and roll. Therefore, P-torque is greatly increased by the optical fiber. Also, flying height(FH) of the slider with TAMR suspension can be largely changed by PSA. In this paper, we focus on the FH by PSA of TAMR suspension. The FH is investigated using various PSA and proper PSA is proposed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.583-584
• /
• 2006

Printing technology has begun to get into the spotlight in many ways due to the low cost effectiveness to existent semi-conductor process. It also has very useful application areas, not only paper printing but also patterning for LCD color tilter, Photovoltaic patterning, RFID antenna, OLED, and so on. In this study, an apparatus of gravure offset printing was developed for fine line width printing. The pattern was composed of $20{\mu}m$ size of continuous lines of which pitch size was $40{\mu}m$. The printed pattern shows that it is possible to make around $20{\mu}m$ line-width printing pattern. The roll-to-roll printing system for fine line-width printing based on primary experiment is presented. For testing of multi-layer printing, the system was designed to be capable of printing two different materials from each printing unit using gravure-offset printing method and have a function of alignment of two printed materials.