• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.499-504
• /
• 1993

To find a way for establishing work roll initial crown according to roll conditions, computer simulation for predicting plate crown in plate mill is done and effects of roll conditions on plate crown is analysed. Roll gap profile and plate crown are measured to be compared to the calculated values. As a result,a regression equation to establish work roll initial crown according to roll cooditions such as backup roll diameter, backup roll crown and work roll crown is obtained.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.3
• /
• pp.73-81
• /
• 1995

To find a way for establishing work roll initial crown according to roll conditions, computer simutation for predicting plate crown in plate mill is done and effects of roll conditions on plate crown is analyzed. Toll gap rorfile and plate crown are measured to be compared to the calculated values. As a result, regression equation to establish work roll initial crown according to roll conditions such as backup roll diameter, backup roll crown and work roll diameter is obtained.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.11
• /
• pp.200-210
• /
• 2002

In twin roll strip casting process, coupled analyses of heat transfer and deformation for the cast roll are carried out by using the finite element program MARC to examine the thermal crown. Shrink fit effect and plastic deformation are considered. The results shows that the thermal crown is greatly influenced by shrink ft and that the thermal crown for POSCO Pilot Caster 2 Copper Roll has “M” shape. The effects of several factors on thermal crown are also investigated. The amount of thermal crown increases as heat flux, casting speed, steeve thickness and casting roll width increase and decreases as the casting roll diameter increases.

• Transactions of Materials Processing
• /
• v.24 no.3
• /
• pp.212-217
• /
• 2015

SmartCrown is a system to control the plate crown by shifting the sine-shaped work rolls in the axial direction. The control range of the plate crown depends on a depth of sine-shaped roll profile because the roll radius varies continuously along the axial direction. When the roll profile is changed to improve the control range, the contact stress between the work roll and the back-up roll also changes. In the current study, the contact stress for various profiles and rolling conditions were analyzed using the finite element method and compared with results from Hertzian contact theory. A submodel method is used to increase the accuracy of the finite element analysis. The analysis results showed that the maximum increase in the contact stress was only 53MPa, so it is anticipated that no back-up roll spalling will occur.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.8
• /
• pp.1451-1457
• /
• 1992

In hot strip rolling, the thickness of strip cannot be retained uniform by several irregular parameters. It has been shown that the load distribution can affect only a small fraction of the excess strip crown, whereas the thermal effects of working roll are the major reason on large changes in the strip center crown during hot rolling. In this study, the temperature distribution of working roll is represented by fourier series expansion. The analytical solution of the resulting thermo-elasticity problem is obtained by love's strain function. The results which are compared with those of the finite element method show good agreements.

• Transactions of Materials Processing
• /
• v.14 no.1 s.73
• /
• pp.43-48
• /
• 2005

The production of metal strip with uniform thickness and flatness are two important problems associated thin strip rolling. The thickness and flatness of strip are affected by the flattening of contact surface between strip and roll, the elastic recovery and the bending of roll. Especially, the flatness of the strip is greatly affected by bending deflection of roll. The roll must be designed considered the elastic deformation of roll. This study describes the measurement of thickness and flatness of strip and shows the crown roll for producing flat strip. But it is difficult to produce the crown roller. The cross rolling that is a simple method which can produce the flat strip is introduced and it is found the optimal cross angle for improvement of flatness of plate. These problems are solved by the MARC code on the basis of elastic-plastic material and the updated Lagrangian formulation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.8
• /
• pp.847-854
• /
• 2007

The battery electrode of a mobile phone is made of layered polymer coated on aluminum foils and the hot rolling process is applied to increase the density per volume of an electrode for a high capacity battery. The flatness of batteries surfaces should be less than $2{\mu}m$. To satisfy the required flatness, the deformation of roll surface due to bending and heating of the roll should be minimized. Complicated hot oil paths of $100^{\circ}C$ inside the roll are required for heating the polymer layers. FEA was used to calculate thermal deformations and temperatures distributions of the roller. Based on FEA, a modified surface curvature called a crown roll was suggested and this gave the area of 30% improved flatness compared with a flat roll. The flat roll satisfied the flatness of $2{\mu}m$ in the length of 340 mm and the crown roll resulted in the longer length of 460 mm. Experiments to measure the temperature distribution and thermal strain were performed and compared with FEA. There were only 6% difference between two results.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.04a
• /
• pp.13-16
• /
• 2009

In order to investigate the effects of geometry factors such as a roil diameter ratio and backup roll crown of the stress concentration factor on the edge of backup roil end, 3-dimensional FEM analyses of stress at the contact of backup roll and work roll assembled in a 4-high strip mill were carried out, It was made clear that the peak stress at the edge is about 2 to 3 times of that at the longitudinal center of the roll barrel and the peak stress proportionally increase with decreasing the ratio of backup roll diameter to work roll diameter Furthermore a crowning on the backup roll is effective to decrease the maximum edge stress.

• Journal of the Korean Society for Precision Engineering
• /
• v.7 no.3
• /
• pp.14-25
• /
• 1990

A model predicting thermal and wear crown in order to control strip crown and shape has been investigated at the hot roll mill. A basic equation of predicting wear crown was obtained experimentally whereas thermal crown was approximately analyzed by the integral method. The calculated result based on the accumulative model of basic eauation coincides with that measured under the real rolling conditions. The effect of wear corwn is also analyzed by the longitudinal feeding method of the work roll. The high frequency feeding method is recommended in removing local wear effectively.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.91-92
• /
• 2007

Control of crown and flatness in plate rolling is important not only for enhancement of the structural precision of products, but also for improving the yield and rolling operation. In the heavy plate mill, there have been strong demands for upgrading plate crown and flatness. In order to satisfy these demands, it is essential to develop the high precision numerical models. This paper gives a general description of the crown and flatness preset control model, work roll bender system, simulation result for shape control.