• Tunnel and Underground Space
• /
• v.25 no.2
• /
• pp.155-167
• /
• 2015

The thermal-hydrological-mechanical (T-H-M) behavior of rock mass surrounding a high-temperature cavern thermal energy storage (CTES) operated for a period of 30 years has been investigated by TOUGH2-FLAC3D simulator. As a fundamental study for the development of prediction and control technologies for the environmental change and rock mass behavior associated with CTES, the key concerns were focused on the hydrological-thermal multiphase flow and the consequential mechanical behavior of the surrounding rock mass, where the insulator performance was not taken into account. In the present study, we considered a large-scale cylindrical cavern at shallow depth storing thermal energy of $350^{\circ}C$. The numerical results showed that the dominant heat transfer mechanism was the conduction in rock mass, and the mechanical behavior of rock mass was influenced by thermal factor (heat) more than hydrological factor (pressure). The effective stress redistribution, displacement and surface uplift caused by heating of rock and boiling of ground-water were discussed, and the potential of shear failure was quantitatively examined. Thermal expansion of rock mass led to the ground-surface uplift on the order of a few centimeters and the development of tensile stress above the storage cavern, increasing the potential of shear failure.

• Geophysics and Geophysical Exploration
• /
• v.15 no.1
• /
• pp.1-7
• /
• 2012

To evaluate methods of determining near-surface shear-wave velocities (${\nu}_s$), we derived dispersion curves of Rayleigh waves generated by both passive and active sources in Chuncheon, Korea. Microtremors were recorded for 5 minutes in each of four triangular arrays with radii of 5 ~ 40 m. Those data were analyzed using the Spatial Autocorrelation method. Rayleigh waves were also generated by a hammer source and recorded in the same area for 2 s using 24 4.5-Hz geophones. Multichannel Analysis of Surface Waves was applied to those data. Velocity spectra were derived with relatively high signal-to-noise ratios in the frequency ranges of 7 ~ 19 and 11 ~ 50 Hz for the microtremors and synthetically generated Rayleigh waves, respectively. The resultant dispersion curves were combined as one and then input to inversion to derive shear wave velocities that were compared with a lithology log from a nearby well. Shearwave velocities in the top soil and soft-rock layers are almost constant with values of 221 and 846 m/s, respectively; while the inverse-modeled ${\nu}_s$ increases linearly in the gravelly sand, cobbles, and weathered-rock layers. If rock type is classified based on shear-wave velocity, the inversion-derived boundary between weathered-rock and soft rock may be about 5 m deeper than in the well log.

• The Journal of Engineering Geology
• /
• v.12 no.4
• /
• pp.421-437
• /
• 2002

In order to quantify the anisotropic properties of rock included joints and shear behavior in joint surface, the mold is Produced for rock joint surface using gypsum Plaster and Peformed for replicated joint models made of cement mortar. Rock sample is measured using mechanical profilometer before testing and their result is expressed quantitatively. The statistical parameters and the fractal dimension by fractal theory for roughness is investigated its coordinate value for numerical process. The shear strength to the shear displacement in low level normal stress ismaintained or increased in most joint models. Their results present that this relationship is depended several roughness properties in joint model for natural rock joint. The relationship between the shear strength and the Properties for profiles estimated by some statistical parameter in roughness has the low correlation and is not constant. The result between the data for direct shear test and using Barton's equation, Barton's equation has not the effectiveness for the effect of anisotropy and has not suitable to recognizing the properties for joint surface. It means that JRC has not the properties of anisotropic rock surface. The fractal dimension is well correlated with the data of direct shear test than those of JRC. New experimental formulae using fractal dimension is comported with the anisotropic properties for direct shear test.

• Tunnel and Underground Space
• /
• v.22 no.2
• /
• pp.106-119
• /
• 2012

Roughness of rock joint has generally been characterized based upon geometrical aspects of a two-dimensional surface profile. The appropriate description of joint roughness, however, should consider the features of roughness mobilization at contact areas under normal and shear loads. In this study, direct shear tests were conducted on the replicas of tensile fractured gneiss joints and the influence of the shear direction on the shear behavior and effective roughness was examined. In this procedure, a joint surface was represented as a group of triangular planes, and the steepness of each plane was characterized using the concepts of the active and inactive micro-slope angles. The contact areas at peak strength which were estimated by a numerical method showed that the locations of the contact areas were mainly dependent on the distribution of the micro-slope angle and the shear behavior of joint was dominated by only the fractions with active micro-slope angles. Therefore, a three-dimensional coefficient for the quantification of rock joint roughness is proposed based on the distribution of active micro-slope angle: active roughness coefficient, $C_r$. Comparison of the active roughness coefficient and the peak shear strength obtained from the experiment suggests that the active roughness coefficient is the effective parameter to quantify the surface roughness and estimate the shear behavior of rock joint.

• Journal of Conservation Science
• /
• v.16 s.16
• /
• pp.77-88
• /
• 2004

This study evaluates the occurrences, phyfical weathering and biological deterioration on rock properties during the dissection process an object of stone pagoda in the Mireuksaji temple site. For restoration and conservation, all kinds of rock properties are carried out detailed scientific investigation and diagnosis. Constituting rocks of the pagoda composed mainly of equi-granular medium grained biotite that rock properties presumed to be use about 3,000 materials. Main external properties of the pagoda are total 446 materials, and the rock properties under the concentration load on the each floors occurred with overlapping fracture, weathering and deteriorations. The 84 materials show highly degraded about $18.8\%$ among the external properties. Representative physicochemical deteriorations are fracture, loss, break, exfoliation, degradation, grain shaped dissolution, relief surface, discoloration and hydroxide precipitates, in this study, the deterioration state of each properties give a precisely description and analysis. Coverage of lichen and algae on the rock surface represented about $85\%$. As the some properties, biological contaminants withered up when spray rock surface with diluted cleaning chemicals. Results of the study are utilized an application for restoration system and detailed investigation during the dissection process of stone cultural properties.

• International Journal of Concrete Structures and Materials
• /
• v.18 no.1E
• /
• pp.23-28
• /
• 2006

In this study, the general theory of fractality is discussed to provide a fundamental understanding of fractal geometry applied to heterogeneous material surfaces like pavement surface and rock surface. It is well known that many physical phenomena and systems are chaotic, random and that the features of roughness are found at a wide spectrum of length scales from the length of the sample to the atomic scales. Studying the mechanics of these physical phenomena, it is absolutely necessary to characterize such multi scaled rough surfaces and to know the structural property of such surfaces at all length scales relevant to the phenomenon. This study emphasizes the role of fractal geometry to characterize the roughness of various surfaces. Pavement roughness and rock surface roughness were examined to correlate their roughness property to fractality.

• Tunnel and Underground Space
• /
• v.10 no.1
• /
• pp.33-44
• /
• 2000

In order to investigate the effect of progressive collapse of underground circular opening on surface subsidence, laboratory model tests were performed. The modelling materials were sand which has been used as KS standard. Six test models which had respectively different depths of openings were produced. Surface subsidence and horizontal displacements were measured according to progressive collapse of underground opening. Some subsidence prediction method such as NCB method, profile function method and influence function method were considered to predict the subsidence of sand models. The profile function method approximated by Gaussian error function was finally suggested as the most appropriate to sand models.

• Tunnel and Underground Space
• /
• v.19 no.3
• /
• pp.174-180
• /
• 2009

This paper gives a brief review of seismicity and seismic monitoring in surface mines. A summary of various researches related to seismicity is presented. Our research focuses on the understanding of seismicity and the application of analytical techniques to seismicity. Seismic monitoring plays an important role in the identification of potential failure planes and thereby predict potential failures. Much of the instrumentation used in our research is derived from earthquake monitoring systems. The major aspects in seismic monitoring are an instrumentation used, size of the network and data acquisition systems. Seismic monitoring in surface mines could be successfully applied to the improvement of safety standards in slope stability.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2003.04a
• /
• pp.151-159
• /
• 2003

This study presents method for self-calibration of the SEM(Scanning Electron Microscope) stereo image using the standard microprobe with same grid pattern and using parallel and central perspective projection equation. Result showed that parallel projection method is more suitable for standard microprobe. The maximum error of 3D coordinates acquired by this method did not exceed 5 $\mu\textrm{m}$, and DSM(Digital Surface Model) for three dimensional measurement of the rock sample was generated by the digital photogrammetry. This result can be used for quantification of micro scale change of shape and analysis of the micro morphology of rock due to weathering.

• Tunnel and Underground Space
• /
• v.6 no.3
• /
• pp.267-273
• /
• 1996

The types of eletric detonators manufactured in korea include instantaneous, decisecond and millisecond delays but number of delay intervals are only limited from No. 1 to No. 20 respectively. It is not sufficient to control accurately millisecond time with these detonators in large surface blasting. But nonelectric system detonators with an unlimited delay time are recently obtained. In this paper the effect of delay time of nonelectric detonator on the level of vibration in surface blasting was studied. A total of 169 data were recorded in the studied area. Blast point-to-measuring point distances ranged from 25 to 100 meter, where charge weight was 1.26 kg per delay.