• Journal of Drive and Control
• /
• v.21 no.1
• /
• pp.53-58
• /
• 2024

With the recent development of intelligence and automation technologies for construction machinery, the demand for safety and efficiency of road-cutting operations has continued to increase. In response to this, a double-blade road cutter has been developed that can automatically cut roads. However, a double-blade road cutter has a load difference between the two blades due to the ground and wear conditions of the cutting blades. The difference in load between the two blades distorts the direction of travel of the cutter. In this study, a vision sensor-based driving guide technology was developed to correct the driving path of road cutters. In addition, we developed a load-sensing technology that detects blade loads in real-time and controls driving speed in the event of overload.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.5
• /
• pp.105-111
• /
• 2003

The three-axis road simulator is the test equipment which can simulate the standardized road conditions for the durability evaluation of automotive components such as suspensions. The road load data are collected and acquired from a vehicle test, and then these data are used to simulate road load conditions by the road simulator which consists of hydraulic actuators, link mechanism and servo controller. The link mechanism must be designed in consideration of the dynamic effect and interference during three axes motions in order to generate accurate motions. In this paper, the structural and kinematic analysis of the link mechanism is performed, and these results can be used for developing the three-axis road simulator. The three-axis road simulator provides considerable savings in cost, development time, and testing risk during developing automotive components.

• Journal of Biosystems Engineering
• /
• v.29 no.5 s.106
• /
• pp.419-424
• /
• 2004

In this study, a series of soil bin experiment was carried out to investigate experimentally the effect of the tire inflation pressure and axle load of tire on the steering torque for the off-road condition. The experiment was performed at the three levels of off-road conditions(ground I, ground II and ground III) and on-road condition(ground IV), four levels of tire inflation pressure(120 kPa, 170 kPa, 220 kPa and 270 kPa), and four levels of axle load(1470N, 1960N, 2450N and 2940N). The results of this study are summarized as follows: 1. Steering torque at the off-road conditions were higher than that on the on-road conditions for all levels of tire inflation pressure and axle load. 2. As the axle load increased, steering torque also increased f3r all experimental ground conditions. 3. For the axle load of 1470N the biggest steering torque was measured on the ground condition I, but as the axle load increased to the value of 2940N the biggest steering torque was measured on the ground condition III. From the above results, it was found that for the low axle load, steering torque gets higher on the soft ground condition, but for the high axle load, steering torque gets higher on hard ground condition for whole range of experimental conditions. 4. As the tire inflation pressure decreased, steering torque increased on the on-road condition, but no specific trend was not found at the off-road conditions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.166-173
• /
• 2002

The wheel bearing hub unit is developed type of wheel bearing unified with the hub parts. It has advantage of reducing the weight and the number of components. And, it also improves uniformity of manufacturing quality, In order to design the wheel bearing hub units, many techniques are used such as load analysis, structure analysis and bearing characteristics analysis and so forth. These techniques need highly accurate load conditions founded on service conditions. In this study, to design the wheel bearing hub units used widespread in passenger cars, the service load was measured through driving tests on the public roads and in the special events. The public roads are classified into highway, intercity road, rural road, urban road, and unpaved road so as to know what the characteristics of the road loads are. The results of the tests showed that the wheel force was relative to the lateral acceleration, and also could be calculated from the lateral acceleration. The lateral acceleration was measured from 0.0G to 0.6G in general driving on the public roads, with different distributions in each road type. In special events, the maximum lateral acceleration was measured from 0.8G to 1.3G.

• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.485-488
• /
• 2008

The structure supporting road sign is a road information facility for ensuring the safe transportation and smooth traffic. But, lots of road information facilities were damaged by the typhoon "Maemi" in 2003. Such damaged facilities should be rehabilitated and could increase economic loss by causing traffic accident. Therefore, in this study, behavior that reduce wind load and improve wind resistance of the structure supporting road sign are studied about wind load beyond design specification by abnormal climate as below. The first is wind load reducing technique such that shear key resist wind load that is not greater than design wind speed but in case that it is over the design wind limit, column member is rotated on the inner steel pipe axis by the brittle failure of shear key. The second is the technique such that fail-safe the overturning of road sign panel by equipment installation in the vertical member. The third is the technique of installing stiffening plate inside the vertical member to relieve stress concentration.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.5
• /
• pp.525-531
• /
• 2011

Recently, the demand of environmentally friendly transportation has increased due to the environmental issues. Electric two-wheeled vehicles do not have the noise pollution nor exhaust gases of vehicles with internal combustion engines. Performance evaluation of an electric two-wheeled vehicle was carried out. A driving test on outdoor roads was performed and a chassis dynamometer was used. The chassis dynamometer simulates the road load of the vehicle. The road load influences the tests using the chassis dynamometer. The differences between the table method and the coasting test for setting the road load was compared and analyzed.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1127-1132
• /
• 2003

Suspension system of vehicle have enough endurance during its life time to protect passenger. Spring is one of major part of vehicle. Thus, a fatigue strength evaluation for leaf spring based on road load response was carried out. At first, strain of leaf spring is measured on the city condition and proving ground condition. And next, the damage analysis of road load response data was carried out. And fatigue test of leaf spring were also carried out. Based on -N life relation, fatigue life of leaf spring was evaluated at belgian mode, city mode and drawing test specification. After that, it is compared the design life of leaf spring and evaluated fatigue life by belgian mode, city mode and drawing test specification. From the above, the maximum load-fatigue life relation of leaf spring was defined by test. and new test target of belgian mode and city mode was proposed to accept design specification of leaf spring. It is expect that proposed test target can verify leaf spring fatigue endurance at specific road condition.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.1
• /
• pp.37-44
• /
• 2014

For testing a two-wheeled vehicle's per-charge range, this study conducted road and chassis dynamometer driving tests. Three typical road routes within Daejeon Metropolitan City were selected for the road-driving test. In the case of CVS-40 mode driving tests using a chassis dynamometer, various road-loading conditions were set. In this study, two-wheeled electric vehicles' per charge range on the road was confirmed through testing, and the range and energy consumption efficiency depending on various chassis dynamometer road load settings were measured. Then, the results of the actual road driving tests were compared with those of the chassis dynamometer driving tests, and road load settings that yielded per-charge range testing results similar to those under actual road driving conditions in the chassis dynamometer experiments were studied.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.544-549
• /
• 2003

In this study, non-linear dynamic FE analysis of a tracked vehicle under the traveling load is performed by FE code ABAQUS. The stability of vehicle is examined using the structure analysis for the road wheel. The dynamic analysis is performed by traveling load. The traveling load include the 6 step loading spectrum about road wheel. The stress level around road wheel are 30 MPa ${\sim}$ 40 MPa. These value are indicated under modified fatigue strength 50.3 MPa. It takes about 3 second to be stable the structure after traveling load.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.10
• /
• pp.773-778
• /
• 2012

A road energy harvester was designed and fabricated to convert mechanical energy from the vehicle load to electrical energy. The road energy harvester is composed of 16 piezoelectric cantilevers. We fabricated prototypes using a vehicle load transfer mechanism. Applying a vehicle load transfer mechanism rather than directly installing energy harvesters under roads decreases the area of road construction and allows more energy harvesters to be installed on the side of the road. The power generation amount with respect to the vehicular velocity change was assessed by installing the vehicle load transfer mechanism form and underground form. The energy harvester installed in the underground form generated power of 4.52 mJ at the vehicular velocity of 50 km/h. Also, power generation of the energy harvester installed in the vehicle load transfer mechanism form was 48.65 mJ at the vehicular velocity of 50 km/h.