• Journal of electromagnetic engineering and science
• /
• 제4권3호
• /
• pp.113-118
• /
• 2004

As an application of ring filters, a new and simple method to determine an inherent-ring-resonance frequency is introduced. The ring filter consists of a ring and two short stubs. They are connected at 90$^{\circ}$ and 270$^{\circ}$ points of the ring and the ring filter may be seen in such way that two filters are connected in parallel. Therefore, if the two powers of the two filters are out-of-phase at the output, the power excited at the input can not be delivered. That can be done by making difference in length of the two short stubs, and when a certain condition is satisfied, a frequency exists where all the excited power is reflected. That is the very inherent-ring-resonance frequency. In the lossless case, the return loss with the condition reaches 0 dB at the inherent-ring-resonance frequency but does not with conductor, dielectric losses and so on. Therefore, the effective loss tangent at a frequency of interest may be obtained correctly. To verify the method, two ring filters have been fabricated in microstrip lines and the measured results show good agreement with the predicted ones.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2000년도 종합학술발표회 논문집 Vol.10 No.1
• /
• pp.319-323
• /
• 2000

A method for miniaturization of microstrip patch antenna without degrading its radiation characteristics is investigated. The ring geometry introduces additional parameters to the antenna that can be used to control its resonance frequency and bandwidth. For a single square ring increasing the size of patch decreases the resonance frequency and bandwidth. To match the antenna to a transmission line and also enhance its bandwidth. the square ring patch is stacked by a square ring patch. The computed results are compared with experiment and good agreement is obtained.

• 한국군사과학기술학회지
• /
• 제24권6호
• /
• pp.577-590
• /
• 2021

In this paper, we theoretically analyzed the self-alignment/navigation performance in the accelerometer resonance state generated by dither motion of ring laser gyroscope in LINS and verified it through simulation. As a result of analysis, it is confirmed that the amplitude of the accelerometer measurement amplified in the accelerometer resonance state is decreased in the process of sampling per the navigation calculation period and that frequency is changed by the aliasing effect too. It was also analysed that the attitude error in self-alignment is determined by the amplitude/frequency of the accelerometer measurement, the gain of the self-alignment loop, and the velocity and position error in the navigation is determined by the amplitude/frequency/phase error of the accelerometer measurement. This analysis and simulation results show that the self-alignment and navigation performance is not be degraded only when the amplification factor of the accelerometer measurement in the accelerometer resonance state is 3 or less

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권10호
• /
• pp.484-490
• /
• 2003

This paper describes with the stator analysis and design of a ring type ultrasonic motor. The design for piezoelectric ceramic and elastic body of stator were calculated by using the finite element method (FEM) that consider the resonance frequency, vibration mode and coupling efficiency. Namely, such results were acquired the calculation result of the piezoelectric ceramic thickness 0.5[mm], elastic body thickness 2.0[mm], resonance frequency 51.8[kHz], vibration mode 7 order and coupling efficient 12.5[%], the outer and inner diameter of vibrator 50[mm], 38[m]. On the basis of such result, the ring type ultrasonic motor was manufactured. Also for driving characteristics of ring type ultrasonic motor, 2-phase inverter was constructed. Then the propriety of this paper was established from comparision of the simulation and an experiment results of the ring type ultrasonic motor.

• Journal of the Optical Society of Korea
• /
• 제2권1호
• /
• pp.1-4
• /
• 1998

The second harmonic light of an 842 nm diode laser was generated from a KNbO3 crystal in an external ring resonator. The power of the second harmonic light was about 0.8 mV at an input fundamental power of 87 mW. The laser frequency was stabilized to the resonance frequency of the ring resonator, and the frequency fluctuation was measured as about 3 MHz.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권5호
• /
• pp.309-317
• /
• 2004

This paper suggested the vibration characteristic improvement by variation mode of ring type ultrasonic motor. Design for the piezoelectric ceramic and elastic body of stator were calculated by the finite element method(FEM) that consider the resonance frequency, vibration mode and coupling efficiency etc. Through the result of vibration analysis from 6 order mode to 8 mode, the 7 order mode was gained very an excellent results that it was the coupling efficient, minimum power loss and bending vibration value. Here over 7 order mode, this paper was acquired that an output current for input voltage was very a large increased results. The result of vibration calculation, from thickness 0.5[mm] to 2[mm], knew the fact that the vibration displacement at 0.5[mm] is an high value too. From such result, this paper was manufactured the ultrasonic motor of outer diameter 5O[mm] , inter 22[mm] having the about 43.86[KHz] resonance frequency. We have gated that a simulation result is 42.2[KHz] and an experiment result is 43.86[KHzl The propriety of this paper was established though comparison. investigation of simulation and experiment result.

• 한국전자파학회논문지
• /
• 제18권7호
• /
• pp.796-808
• /
• 2007

이 논문에서는 split-ring 공진기와 spiral 공진기를 complementary 형태로 구현한 새로운 형태의 두 가지 마이크로스트립 대역저지 필터를 제안하였다. 첫 번째는 마이크로스트립 전송 선로의 중앙 선로에 세 개의 split-ring 공진기를 일렬로 배열시켜 에칭 시킨 것이다. 중앙 선로에 구현된 세 개의 split-ring 공진기와 수직으로 시간에 따라 변하는 전계가 걸리면 특정 공진 주파수에서 유효 투자율이 음이 되는 현상이 벌어지며, 이에 따라 전파가 더 이상 진행하지 못하게 된다. 이는 특정 공진 주파수에서 대역저지 현상이 나타나는 것을 의미한다. 두 번째는 첫 번째 것과 비슷하게 마이크로스트립의 중앙 선로에 spiral 공진기를 세 개 나열하여 에칭하였다. Spiral 공진기는 그 축에 수직한 방향으로 전계가 걸렸을 때 특정 공진 주파수에서 self-resonance 현상이 일어나며, 이것이 대역저지 특성으로 나타난다. 제안된 두 필터는 쉽게 공진 주파수와 대역저지 폭을 결정할 수 있고, 매우 작은 크기를 갖으며, 통과대역 내에서 삽입손실이 거의 없으며, 매우 날카로운 스커트 특성을 갖는다. 또한 제작하기 쉽고, 향후 MMIC에 적용하기 쉬울 것으로 예상한다.

• 한국전기전자재료학회논문지
• /
• 제16권6호
• /
• pp.484-489
• /
• 2003

In this paper, a single phase driven piezoelectric motor design was presented for linear motion Two metal/ceramic composite actuators, a piezoelectric ring which was bonded to a metal endcap from one side, were used as the active elements of this motor. The motor was composed of a piezoelectric ceramic, a metal ring which has 4 arms, and a guider. Motors with 30 [mm] and 35 [mm] diameter were studied by finite element analysis and experiments. As results, the maximum speed of motor was obtained at resonance frequency. When the applied voltage of the motor increased, the speed was increased. Also, bidirectional motion of the motor was achieved by combining two motors which have different resonance frequency. But the characteristics of bidirectional motion were not equaled, because of the problem of reproduction on the fabrication and the experiment. If present motor is used at the auto-zoom device of a camera, it will have much advantage. Because the direct linear motion can be achieved with a simple structure of motor and no gearbox of total system.

• 한국전기전자재료학회논문지
• /
• 제17권2호
• /
• pp.171-177
• /
• 2004

Voltage step-down characteristics in Ring/Dot type piezoelectric transformer were examined as a function of the area of input electrode when the area of output electrode is fixed. The effects of driving frequency and load resistance on the voltage step-down characteristics were also examined. Voltage gain was greatly dependent on the driving frequency and load resistance, and showed a maximum gain at resonance frequency of the step-down transformer. The frequency where the maximum cutout voltage appears increased about 0.2％ as the load resistance increased from 10 to 150 Ω. As the area of input electrode increased, the voltage gain and the efficiency of the transformer increased. Frequency dependence of efficiency of the step-down transformer revealed a similar tendency with the voltage gain curves. The maximum efficiency remarked 94% when the input voltage and the load resistance were 20 Vpp and 120 Ω, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.722-725
• /
• 2004

Voltage step-down characteristics in Ring/Dot type piezoelectric transformer were examined as a function of the area of input electrode when the area of output electrode is fixed. The effects of driving frequency and load resistance on the voltage step-down characteristics were also examined. Voltage gain was greatly dependent on the driving frequency and load resistance, and showed a maximum gain at resonance frequency of the step-down transformer. The frequency where the maximum output voltage appears increased about 0.2% as the load resistance increased from 10 to $150\Omega$. As the area of input electrode increased, the voltage gain and the efficiency of the transformer increased. Frequency dependence of efficiency of the step-down transformer revealed a similar tendency with the voltage gain curves. The maximum efficiency remarked 94% when the input voltage and the load resistance were 20 $V_{PP}$ and $120\Omega$, respectively.